Sherman Transmissions Different Styles and How to Shift Them
ฝัง
- เผยแพร่เมื่อ 4 มี.ค. 2017
- Shifting the step-up or step-down. Shifting the sherman combo. Shifting the combo on the 4000 heavy duty industrial. Shifting the reverser on the 4000 heavy duty industrial forklift.
- ยานยนต์และพาหนะ
![แฉ [2/4] 12 ก.ค. 67 เจ้าของไวรัลดังในโซเชียล 'ลิลลี่ เหงียน' ฝันอยากเข้าวงการ โดนหลอกสารพัด | GMM25](http://i.ytimg.com/vi/7zntQK2U8-8/mqdefault.jpg)
Explained very well. Thanks Kirk, for the information and demonstration. Very helpful for the guys who are new to the Fords equiped with those Sherman aux. transmissions.
Thank you, explained in a lucid and informative manner..
Thanks for the demo, I have Sherman Combination, but had not seen the standard position shown.
Great video. 👍
I have collected a few Sherman transmissions; I need to get busy a install them. 😆
Compro una transmission sherman para ford 8N. No sabia que existia. Gracias por su explicación.
Love the intro!
Thanks for the info my dad bought a 53 Jubilee it turns out we have that step up and step down combo trans. It also has a franco loader 1200 with it
TheCattlekings How fast will the tractor run in the (step up) range?
Kirk good video workingbon a friend's tractor figured out it has a Hubb duel shift transmission any idea where we could find the compression spring and the grommet that seals the side case
I don't know where to find parts for your Hupp.
Do you have to use the clutch to activate it? And can you shift while driving? Thanks for the video!
You do indeed need to incage the clutch to shift. You should be fully stopped before trying to change ranges.
cdjhyoung alright thank you!
What is the most common Sherman transmission?
We had a 9N with an auxiliary three speed transmission the had the handle on the right side of the tractor. Do you have any information about this set up?
On the right side of the tractor with lever before the main tans closer to bellhousing would probably be a Hupp or an F&T auxiliary trans. If the handle was located after the main trans on the round side cover it would be a howard trans
It is the Sherman and a Hupp transmission the same…
I see a couple Hupp over/under transmissions on eBay but I’m not sure about them so I’m reluctant to buy it
Hupp and sherman are not the same trans although they are similar. I would only buy from someone who deals with sherman trans rather then someone on ebay who is parting out tractors looking to make a quick buck. Condition is a big factor with these units.
I have the sherman combination Im sure based off video but I can't get it to shift at all. So no idea if I'm in standard range or high range. Any help would be great
I just test drove an 8n with a hi-low Sherman. It sounds like yours is in standard position. Try pushing the lever towards the engine while in the middle neutral position. Then you should have low range in forward and high when pulled back.
Sherman Transmissions can I shif from low to high range old 601 Ford tractor when rolling
The sheman transmission was not a shift on the fly transmission. I would not recommend you do that. That said there are people that do this at a slow roll but if the gears are not lined up it's possible to chip or break gears. Other than wear parts the other parts in the trans can be expensive. I have quite a collection on them and I do not sell parts. I just put a combo in my 641 this passed week. Since you have a 601 series in 1958 at serial number 14256 they chained the input shaft from a course spline to a fine spline along with the nose cone. if you serial is above that number you will have the fine spline shaft which are harder to find the than the earlier course spline ones. The shermans were very good trans and can last for many years if you take care of them.
what options do i have for overdrive transmissions? i would like to get around 45-50 mph, suggestions on a tractor too, one that supports the high crop axles i could flip to lower it.
thanks
Shit can you get 120 mph out of these tractors souped up not stock