How to Install a Timing Chain Cover on a Small Block V8: Easy Step-by-Step Guide
ฝัง
- เผยแพร่เมื่อ 26 ส.ค. 2024
- Learn how to properly install a timing chain cover on a small block V8 engine with our easy-to-follow, step-by-step guide. This video will walk you through each step of the process, from prepping the surfaces to securing the cover, ensuring a perfect fit and a leak-free seal. Whether you're rebuilding your engine or performing routine maintenance, this tutorial is packed with expert tips to make the job simple and efficient. Perfect for DIY mechanics and car enthusiasts looking to enhance their skills!
#TimingChainCover #SmallBlockV8 #EngineRepair #CarMaintenance #DIYAutoRepair #EngineRebuild #V8Engine #AutoDIY #MechanicSkills
Parts:
Edelbrock 7802 Performer-Link Timing Chain and Gear Set
amzn.to/36dpeUi
Tools:
TEKTON 1/2 Inch Drive Click Torque Wrench (10-150 ft.-lb.) | 24335
amzn.to/3jCqND2
TEKTON 3/8 Inch Drive Click Torque Wrench (10-80 ft.-lb.) | 24330
amzn.to/3jGgXjq
TEKTON 1/2 Inch Drive 6-Point Socket Set, 11-Piece (3/8-1 in.) | SHD92101
amzn.to/3dGTo6q
TEKTON 1/2 Inch Drive 6-Point Socket Set, 15-Piece (10-24 mm) | SHD92102
amzn.to/3dGb95G
TEKTON 3/8 Inch Drive 6-Point Socket Set, 21-Piece (5/16-3/4 in, 8-19 mm) | SHD91201
amzn.to/3qOAhfV
Things used to make this video
1. Adobe Premier Editing Software amzn.to/2DOgo1b
2. Adobe After Effects amzn.to/2YaezUd
3. Abobe Photoshop amzn.to/2Ll6dYl
4. Westcott Flex Daylight Set amzn.to/2H1HOBs
5. Sanken COS-11D Lavalier Mic amzn.to/2VeAzjS
6. DJI Mavic Pro Fly More Combo amzn.to/2Low8hC
7. Epic GoPro / Action Camera Mount for your Boat amzn.to/2VevCaG
8. Dracast Pro On-Camera Light amzn.to/2PTwcVp
9. Dracast Halo Ring Led Light amzn.to/2H7yvkZ
10. Nikon D5600 24.2 MP DSLR Camera amzn.to/2LpD91M
11. Sony PXW-FS7 XDCAM Super 35 Camera System amzn.to/2DWufml
12. Quick Release Shoulder Plate amzn.to/2JqFeYS
#DIY #chevrolet #howto
For more info go to: gmhowto
this man is a wealth of knowledge
Love these videos. Helped a ton with my 355 project. Thanks
This what I’m getting done to my skylark timing chain heater pump in at tie rods inner/outer.
Great video. But what about the timing tab? I'm having a hell of a time finding one that sits tight to the harmonic balancer..
Smart guy, thanks for the videos
A little lube on the shaft seal always helps too.
You're a bad man very informative thank you
how about with the engine in the car? With the oil pan on.
Take the engine out
Take front bolts out of the pan hope for the best
@@mariolt4940 I tried that, didn't work. I ended up dremelling a seal, fitting it in and sealing it with ultra silicone.
Could’ve put on the bottom seal
Mr Rob I have question. I broke one of the screws on my cover. I accidentally heard 120 ft lbs when it was inch pounds. Would one bolt missing cause a leak?
Where is the timming tab?
120 in pounds? The damper 5/8 bolt is torqued at 60 pounds?
That is 120 INCH pounds...Not 60 FOOT pounds in tourqe.Very different rating system.Inch pounds is very light tourqe ratings.Foot pounds is medium to large tourqe ratings.
What tool is used to take the pulley off the engine and put it back on, or more specific off the crankshaft. My other quandary is what tool is used to turn the crankshaft, without stripping the 5/8 bolt to acquire T.D.C.?
does it matter that the gasket is stripe facing engine or gasket stripe facing out ? Which way? does it matter?
U didn't put the rubber piece on?
Should you use RTV with a cork gasket?
Ur the man
I never understood why use a paper gasket with silicone. why not just use the silicone by its self?
Allen McKinney technically, the paper gasket SHOULD seal it by itself. The problem is after years of use the mating surfaces become slightly uneven or develop minor pits on the sealing surface. Also, the use for the MINOR coating is to hold the gasket and bolt holes on the gasket in place while you are bolting it up, plus it assists in sealing any imperfections. I hope this helps.
Where does the timing tab go?
Would of been a better video if you went and installed the oil pan also!
we did in the next video
Wouldn t you put the balancer on before tightening the cover down ?
How will you put the cover on if the balancer is in the way?
I mean the cover would already be on but not tight then put the balancer on so it's through the seal then tighten cover when the seal is centered.
Do you need a larger timing chain cover for double rollers? I have a 71 302 I'm going to do it on.
Kevin Horan some. I'm looking at a 2 piece timing cover so I can access the chain in the future and the cast aluminum vs won't clear a double roller.
Yes a stock will fit but you'll have have the block relieved by machine shop
Hey David im just about to install a brand new timing chain on my sbc 350 but the engines still in a pickup i noticed the timing cover has a lip that goes onto the oil pan and was wondering what would be the easiest way to install the cover back on should i just loosen all the bolts on the oil pan? Thanks ahead of time.
Loosen the bolts on the oil pan.
Hey! It's Peter Griffin!
he's been smoking spray-paint....120 psi torque,?your gonna murder the cover....no bueno.
120 inch pounds is 10 foot pounds👍
Just Play my summer car
looks like a 400ci
he looks like a big block himself
Goofy sob
No one needs to watch you apply RTV for any length of time. No one needs to see you putting each bolt in. You waste people's time. Thumbs down. Go away.
That was as waist of my time as anything I seen on here Do it in a 4#4 Chevy from start to finish I noticed you thought you were being funny at the end for waisting our time
WASTE, fool! You WASTED our time commenting!