Whirlpool Gold French Door Refrigerator Not Cooling Well Diagnosis and Repair

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 91

  • @rstew-41
    @rstew-41 ปีที่แล้ว +2

    3 years after your video you are still saving people thousands of dollars you are awesome thank you

  • @triprovoked508
    @triprovoked508 3 ปีที่แล้ว +7

    I searched and watched so many videos. I finally found this one that explained in a simple and precise way. Thanks.

  • @timfeehan9772
    @timfeehan9772 4 ปีที่แล้ว +6

    Dear Mr. Beard,
    Both you and your videos are absolutely awesome! You saved me a service call and most likely a couple of hundred dollars! I appreciate your style and approach to appliance repair. You have a very calm and straight-forward approach that virtually anyone can follow. I have a 12 yo Whirlpool French Door Refrigerator. The freezer was working fine, but the refrigerator compartment was not cooling. I discovered that the air circulation vent in the back of the freezer was icing up. After coming across your videos, I found your instructions for performing a "long" defrost on the freezer. After entering in the codes as you state in your video, the ice on the vents disappeared, and the refrigerator compartment is cooling again! The inside temperature went from 65 down to 40 degrees. Thanks so much for sharing your expertise!

  • @msirilla
    @msirilla 3 ปีที่แล้ว +1

    Thank you. Watched many other videos but yours was the only one that helped. Easy to follow - good job!

  • @redlinechavez
    @redlinechavez 4 ปีที่แล้ว +5

    Wow you are amazing! Using your schematic and video, you made it so easy to manually check these components in question. You sure made me feel awesome in further troubleshooting this problem. The defrost terminator measured 0.1 ohms and the defrost heating element is reading open. No wonder so far that I could not make the defrost to work in the forced mode.
    Thank you very much!!!!!!

  • @aneily
    @aneily 4 ปีที่แล้ว

    Fixed fridge. July temperatures melting everything. Darn control board. Not reading anything, just dashes no numbers.
    This video saved me
    Thank you!!!

  • @leastofall123
    @leastofall123 4 ปีที่แล้ว +1

    Super helpful video. Thank you for your clear concise narration. The written instructions for programming made it vey easy to follow. I'll be calling tomorrow for parts.

  • @michaelewert9989
    @michaelewert9989 4 หลายเดือนก่อน

    Excellent video!!! Thank you for saving me a ton on fixing my old fridge!!!

  • @flaviopagliero301
    @flaviopagliero301 ปีที่แล้ว +1

    Mr. Beard, I deeply appreciate your concise and detailed video showing what to look for in components how to repair the non cooling fridge but functional freezer (with some "snow"). Question, prior owner of my fridge had taken the model # and "code" sticker off the inside of fridge (Kenmore fridge). My other fridge (Whirlpool gold french door) looks identical as the Kenmore fridge. Seeing the same mother board works for various fridge models, I'm wondering if I could use the same "code" from my functioning Whirlpool fridge if I choose to replace the mother board? again, both fridges look exactly the same in both interior and exterior with the exception of the bottom vegetable drawer.
    I thank you in advance for your time and help with this.
    You have saved me a lot of money in service call.
    Thank you, Thank you, Thank you!
    Sincerely,
    F

  • @fredredman7512
    @fredredman7512 3 ปีที่แล้ว

    You are a really good technician. I worked as a technician over 20 years ago and your knowledge, skills and ability to explain are exceptional. Thanks.

  • @travionkaneon2510
    @travionkaneon2510 4 ปีที่แล้ว +2

    Amazing video, with the best content. I've had this problem with me fridge forever. Great job, much respect to you sir.

  • @Pretzel114
    @Pretzel114 4 ปีที่แล้ว +2

    Great video!!! Thanks again. Learning a lot. Helps with my apprenticship ship training.

  • @anuragtestdata3830
    @anuragtestdata3830 3 ปีที่แล้ว

    Man. You saved a lot of money for me. Thanks.

  • @Peter__77
    @Peter__77 2 ปีที่แล้ว

    Awesome video! Great job explaining steps. Now I can fix the nightmare that this refrigerator is

  • @randykruger
    @randykruger 4 ปีที่แล้ว +3

    Awesome video !!
    I didn't have to replace any parts in my fridge, I just unplugged it for 24 hours and cleaned the coils and now working great for a week,but the fridge was in a really hot room So I'm guessing it was just working overtime.

  • @felmasri
    @felmasri 8 หลายเดือนก่อน

    you are the best who explained this

  • @rogerjones8276
    @rogerjones8276 4 ปีที่แล้ว +1

    Very informative,and goes at a speed at which one can absorb the info

  • @robertlindell6674
    @robertlindell6674 ปีที่แล้ว

    Great video..lots of help thank you

  • @delwaynemiotke4964
    @delwaynemiotke4964 ปีที่แล้ว

    I'm having that problem with the exact same refrigerator, don't think the compressor is running. Put in a new starter relay but no different. Would that be a bad board. I hope you have a way to let me know. I've watched so many videos that got me nowhere. You have the most awesome way and easy to understand. Please help me fix it. I hate to be beat by a machine.

  • @OneBadAgent13X
    @OneBadAgent13X 3 ปีที่แล้ว

    Thank you so much for making this video it helped me to save from buying a brand new refrigerator it would have cost me over $2,000

  • @sollorstance1632
    @sollorstance1632 3 หลายเดือนก่อน

    Great help. Thank you

  • @skijumpersc81
    @skijumpersc81 ปีที่แล้ว

    I'm trying to diagnose a whirlpool french door that's having this same issue. Both the defrost terminator (0.5) and defrost heater (28.5) tested ok, but some of the how to pages mention testing the thermistor. Did testing the defrost terminator tell us if the thermistor is functional or should I test that separately? Are there other steps I should take before ordering a new jazz board?

  • @im2moose54
    @im2moose54 3 ปีที่แล้ว +1

    What would be the problem with the refrigerator icing behind the deli drawer and then the top shelves are not cooling well?

  • @marketheridge1657
    @marketheridge1657 2 ปีที่แล้ว

    Do you have a video where you’ve solved the same issue on a JennAir French Door? Thinking I’ve got a jazz board problem. Can’t find the location of the board to begin testing. Thanks, your videos are very informative.

  • @GolfBert
    @GolfBert 2 ปีที่แล้ว

    great vid!!! My fridge was a warm today and freezer very cold. I can see coils are frosty. I put it into L defrost mode. Do I shut the doors after i put it into defrost? How long should it take to defrost?

  • @steelman8669
    @steelman8669 3 ปีที่แล้ว

    This video was great helped me a lot and saved me a lot of 💰 thanks

  • @roeeovsey7773
    @roeeovsey7773 3 ปีที่แล้ว +1

    Thank you so much 💓!
    In my case, its not a main control and not a thermistor and not a heater 🙄🤔.. Possibility for wiring issue, some how ??!

  • @statiasnyder7921
    @statiasnyder7921 4 ปีที่แล้ว +2

    I just bought a used fridge from someone and it isn't cooling down as much as it should. Temps between fridge and freezer hover between 50 and 60. Obviously, I can't use ice or frost as an indicator that it is a defrost issue. Any ideas??

  • @oooo-xw4io
    @oooo-xw4io 4 ปีที่แล้ว +2

    Nice video bud, thank you. I have same exact fridge so this is a huge help for me. It is just not cooling at all no more & it used to cool after I cleaned the dust off coils, but not more. My Defrost Terminator tested at 50.10 Ohms & the heater is testing at 30. Do you do a vid replacing that part, if not any references? Thanks again bud & keep doing what you do.

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  4 ปีที่แล้ว

      Sounds like a bad terminator to me. Should be reading 0.0 or 0.1 ohms.

  • @joatmon7621
    @joatmon7621 4 ปีที่แล้ว

    You are the man! Thanks for sharing your knowledge to help us out!!!

  • @littlethislittlethat456
    @littlethislittlethat456 2 ปีที่แล้ว

    Thank you for this video! It helped me out. John

  • @RayRay-nb7tn
    @RayRay-nb7tn 4 ปีที่แล้ว

    Never had a chance to work on on of those model fridge yet. Interesting how you do the reset program. Very nice video again. Haven't been on in a long time. But I thank you for the videos and knowledge. Be safe bud.

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  4 ปีที่แล้ว +1

      Thanks again Ray Ray. Took me awhile to understand this one. Seen it many times. One of the best fridges to own. If you find someone getting rid of one scoop it up.

    • @RayRay-nb7tn
      @RayRay-nb7tn 4 ปีที่แล้ว

      Will do sounds great

  • @jjhi2760
    @jjhi2760 3 ปีที่แล้ว

    I have a similar refrigerator and situation I thought I was to replace the Jazz board. I tested the defrost terminator (brown and orange) in a completely defrosted state and go a reading of 56 ohms and tested the defrost heater and got 27.5 ohms. So I’m not changing the board only the defrost terminator does that sound right?

  • @danielholt6741
    @danielholt6741 3 ปีที่แล้ว

    Fantastic video. I learned so much!!!

  • @MrPapi63
    @MrPapi63 4 ปีที่แล้ว

    Thank you this video helped me out tons. Keep up the great work

  • @williamsfamily756
    @williamsfamily756 25 วันที่ผ่านมา

    We have a Whirlpol single door with freezer on bottom, The freezer works fine but the refrigerator is warm. Any Ideas? Thanks

  • @nelsonblackburn6605
    @nelsonblackburn6605 4 ปีที่แล้ว +1

    So, exact same problem as yours. So, tested the heating element: 30 point something ohms. Defrost terminator measures 1.6 to 1.7 ohms...is that ok? It could be the multimeter setting as mine only goes as low as 200 ohms so that might actually be .016-.017? I'm inclined to think it is the jazz board, but I had one other question: you said it is not the defrost timer; did you test it or how do you know? I did a forced defrost and that did work if that sheds any light. Great video, btw! I appreciate any insight you might have that could help me with mine. Again, thanks!

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  4 ปีที่แล้ว +1

      I would start with the Defrost terminator first. You want it to be less than one ohm for sure. That can cut power to the element making it not heat as well and turn off the defrost cycle prematurely. I would start with that and get the jazz board afterwards if it continues to have problems.

  • @MarceloTinelli.
    @MarceloTinelli. 4 หลายเดือนก่อน

    I have the same refrigerator only that on my display I have two horizontal lines, how can I solve that?

  • @genekerr8064
    @genekerr8064 2 ปีที่แล้ว

    New French Door Whirlpool can't open cover over defrost timer. No screws. Any suggestions?

  • @tamermido11
    @tamermido11 11 หลายเดือนก่อน

    How long is short defrost takes?

  • @mindlab780ab6
    @mindlab780ab6 4 ปีที่แล้ว

    Thank you so much for your sharing of the video . I learned a lot.

  • @karenrenner6326
    @karenrenner6326 3 ปีที่แล้ว

    Fantastic tutorial, Thank you

  • @joshchilton7431
    @joshchilton7431 4 ปีที่แล้ว

    Great video very clear and informative! Thanks

  • @Vmartin70EZ
    @Vmartin70EZ 3 ปีที่แล้ว

    Could this be caused by excessive build up of debris clogging the condenser coils in the bottom?

  • @mitchmize5674
    @mitchmize5674 4 ปีที่แล้ว

    Awesome video helped me find out it maybe my board, was wondering if there’s a difference between board numbers 12784414 and 12784415? Was going to get a board from Amazon but my board (12784414) isn’t listed, thanks for your help!!!

  • @markmckinley5989
    @markmckinley5989 4 ปีที่แล้ว

    So is it just the relay that goes bad on the control board?

  • @canadieyoung2709
    @canadieyoung2709 4 ปีที่แล้ว

    Can you show video of what the hoses are supposed to be connected to on the back of this refrigerator please

  • @finallyamommy1
    @finallyamommy1 3 ปีที่แล้ว

    I followed everything you said and before I buy the jazz board, I just want to confirm that a bad board will restrict power yo the fan. I've taken everything apart and I did have a nice ice ball in the top left of the freezer. While I was I there I noticed the fan is not getting 120v. Will replacing the jazz board fix that?

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  3 ปีที่แล้ว

      The fan may not get power unless the door switch is closed. Make sure it’s not that simple first.
      I find that the ice build up in the top left where the intake is, is caused by an air leak. Look at the gaskets and see if you can find where it is not sealing around the door properly.
      This videos shows an issue with the defrost. If the whole evaporator is not ice up than your defrost system is working. You probably have an air leak.

  • @ThuyPham-ih1iv
    @ThuyPham-ih1iv 4 ปีที่แล้ว

    Hi. Your video very helpful. Thanks. I need help my refrigerator is exactly the same as you show. I checked everything like you and it show good. But it ice up and will not defrosting. I have to manual force it defrosting and it will
    defrosting. I thinks my timer is not working. I replaced both boards but still do the same. Where is the timer defrosting board at ? Thanks for doing good educational.

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  4 ปีที่แล้ว

      The timer is in that board you replaced. double check they defrost thermostat. It might close at iced over situations but not in a normal working situation. the evaporator can get to negative number of degrees with all that ice build up. If I was a betting man I would think that is it.

    • @ThuyPham-ih1iv
      @ThuyPham-ih1iv 4 ปีที่แล้ว

      @@BeardedApplianceRepair Thanks for the advice, I did replaced the defrost thermostat, because that the only device that I haven't changed. It worked like the champ. Thanks again you are the Pro. Have a great successful and happiness in life.

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  4 ปีที่แล้ว

      @@ThuyPham-ih1iv glad to be of service! Glad you got her fixed.

    • @michaelchung2448
      @michaelchung2448 3 ปีที่แล้ว

      @@ThuyPham-ih1iv where can I find the defrost thermostat in the fridge?

  • @novellahouse
    @novellahouse 2 ปีที่แล้ว

    Can you please tell me where the defrost timer is located on this model

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  2 ปีที่แล้ว +1

      There is not one. It is in the control. The “jazz board”. This videos should help you diagnose it if you are competent.

    • @novellahouse
      @novellahouse 2 ปีที่แล้ว

      Thanks for responding so quickly. Ive already changed the jazz board, start device and run capacitor and defrost thermostat. Freezer is still not defrosting. In the video you did state that it could be the defrost timer. Oh and forced defrost doesn't work. Now..after I changed the other parts the refrigerator was cooling as it should but freezer i noticed thru the vent was getting frosty.

  • @robertbaker1824
    @robertbaker1824 4 ปีที่แล้ว

    Thank you

  • @boopernator
    @boopernator 3 ปีที่แล้ว

    Why didn't my lead technician show me how to ohm those components from the Jazz board? Thank you for teaching me a better way to do my diagnostics.

    • @BeardedApplianceRepair
      @BeardedApplianceRepair  3 ปีที่แล้ว

      Glad to be of service. I will say we can't know everything. By looking at the schematic though I bet he could figure it out though. I am sure he knows a ton of good stuff I do not know as well.

  • @ses.t129
    @ses.t129 4 ปีที่แล้ว

    Does it have a filter for the ice maker?

  • @brookswho3986
    @brookswho3986 3 ปีที่แล้ว

    Said you know what the problem was but how did you find the problem?

  • @Drylibra306
    @Drylibra306 ปีที่แล้ว

    where is the defrost terminator located at?

  • @brookswho3986
    @brookswho3986 4 ปีที่แล้ว

    I've got one but freezer is fine but fridge comes and goes?
    Can you give any pointers?

    • @finallyamommy1
      @finallyamommy1 3 ปีที่แล้ว +1

      That's what I'm working with. I've figured out that the fan isn't coming on. After testing it with the meter I found it's not getting 120v. I'm waiting a response to my question. Will replacing the jazz board fix the power to the fan

  • @mr.resistor7325
    @mr.resistor7325 3 ปีที่แล้ว

    When you refer to the defrost terminator, that is the thermostat, no?

  • @dcwashington2858
    @dcwashington2858 4 ปีที่แล้ว +1

    What does it mean when I'm just getting dashes instead of numbers? It's been this for a couple months now

  • @scott-vm1bu
    @scott-vm1bu 3 ปีที่แล้ว

    You said multiple times "defrost terminator", is that the same as the defrost thermostat?

  • @wonderwond
    @wonderwond 3 ปีที่แล้ว

    mine says 0.4 and 30.0 that normal ??

  • @wonderwond
    @wonderwond 3 ปีที่แล้ว

    fellas dont forget to clean under it on the front side round oval slots found more lint and kitty hair and more than a dryer could produce lolz,, made my freezer make ice much faster now, but mine is still freezing up, fan not blowing up into the fridge part, where the heater is is a ball of ice about size of a baseball

  • @kouroshlakfard5706
    @kouroshlakfard5706 4 ปีที่แล้ว

    Thank you sir ..................

  • @carlosepiscopo7836
    @carlosepiscopo7836 4 ปีที่แล้ว

    awsome

  • @elkameno1959
    @elkameno1959 ปีที่แล้ว

    how much is that?

  • @sergiocabrera1152
    @sergiocabrera1152 4 ปีที่แล้ว

    Mi fridge is not cooling bu the settings are set to dash and dash, that is "-" and "-" I cannot find anyone mentioning this problem, help!!!

  • @miralmocampos6664
    @miralmocampos6664 3 ปีที่แล้ว

    Damn man ty

  • @mr.resistor7325
    @mr.resistor7325 3 ปีที่แล้ว

    Wish I'd have seen this before pulling the heater only to find it's good FML :-)

  • @spencerstone9683
    @spencerstone9683 2 ปีที่แล้ว

    Bearded man does it again..I owe you some cold ones for all the money you've saved me braa!

  • @BobS91764
    @BobS91764 3 ปีที่แล้ว

    He definitely knows his chit.

  • @Crystalyne73
    @Crystalyne73 2 ปีที่แล้ว

    You still available for questions?

  • @BobS91764
    @BobS91764 3 ปีที่แล้ว

    I have a question for you young man.