Ahh, now this all makes sense! But I dont understand why they chose this trim over the old one, its as you said unpractical for almost everything other than Multirotors. And thank you for the upload ;)
We only release videos on Tuesdays and Fridays (and now and again an extra bonus one at the weekend). Very few videos are released publicly on the day they are uploaded. This was created to answer a specific subscriber request but we're sharing it with all of the subscribers..
I'm almost convinced with this radio, with the trim functionality is the stick movement for the trim after pressing the button proportional to the amount of stick input or is any stick input in a direction classed as a little bit of trim in that direction?
That’s how have the back buttons set, I have them both set as reset buttons for timer 1 & 2, timer 1 activates with my arm switch and timer 2 is a 5 minute countdown activated with switch d
if you want to use 5 channels and one for a switch, does that mean you can only use one switch? and is there a way to use multiple switches without utilising the other channels? thanks!
Not sure if you encountered the problem that I have with this radio.. Mine turns on as soon as I plug in the batteries and if you turn it off it turns back on. I tried flashing the latest software and cleaning the power buttons but it still turns on by itself... very annoying especially if you forget to remove the batteries when you want to store the radio.
I have assigned vrA/vrB to control pitch and rudder of a camera gimbal, but since those are self-centering, the gimbal always returns to it's starting position when I leave the vrA/vrB sticks. Is there any way I could control gimbal, without having to continuously have my finger to vrA/vrB analogs?
Hello sir i had f450 setup with naza m lite and flysky fs i6s ,i have issue when i arm my quad i face issue after throttle is zero my quad motor still working they not stop. What i need to do
I am not familiar with that flight controller. I'd check the minimum throttle setting or see if there is a setting that stops the rotors at zero throttle. Best of luck! !
Those controls dot have ant special functions and are assigned to the outputs just like any of the others. No video specifically on them. Why do you ask?
I was wondering if I could use them on a 2-axis camera gimbal one for up/down and the other left/right. I bought one of these radios (it won't be here for another month) and I'll be using it on a Naze32 FC in 450mm quad. Basically building a quad exactly like you told us in all your earlier videos.
Not easily, there is a mix function in the menu but the lack of trim tabs also mean that it's less than ideal. I'd look at another radio with mixes for planes and trim tabs if you're into fixed wing. I'm a huge fan of the FrSky Q X7 personally..
Ahh, now this all makes sense! But I dont understand why they chose this trim over the old one, its as you said unpractical for almost everything other than Multirotors. And thank you for the upload ;)
We only release videos on Tuesdays and Fridays (and now and again an extra bonus one at the weekend). Very few videos are released publicly on the day they are uploaded. This was created to answer a specific subscriber request but we're sharing it with all of the subscribers..
No worries - subscribers can find all kinds of videos and goodies hiding away in the playlist sometimes weeks in advance of them coming out.. ;D
The back buttons are toggled on Turnigy and momentarily on the FlySky.
gamerpaddy ooo that's intresting... Id like my flysky rear buttons to toggle.
Any firmware updates for this..
I'm almost convinced with this radio, with the trim functionality is the stick movement for the trim after pressing the button proportional to the amount of stick input or is any stick input in a direction classed as a little bit of trim in that direction?
We are watching. Thanks. Thumbs up.
We are grateful. Thank you! :D
I suppose the back buttons could also be used to trigger timers.
That’s how have the back buttons set, I have them both set as reset buttons for timer 1 & 2, timer 1 activates with my arm switch and timer 2 is a 5 minute countdown activated with switch d
Lee, couldn't they be setup to go into a flight mode to perform a trick and then come back to Stabilize when released ? CHEERS !
+One Two horizon mode does that for you. Happy flying!
if you want to use 5 channels and one for a switch, does that mean you can only use one switch? and is there a way to use multiple switches without utilising the other channels? thanks!
+nemo bondt you can mix several controls to set the flight modes and have that control CH5. See our video in the i6s playlist on that..
Painless360 thanks! I've watched the whole playlist before but I haven't come across that video. I will take a better look then!
How do I change the buttons from non momentary to momentary(I have the Turnigy which has them configured as non momentary switches)
Not sure if you encountered the problem that I have with this radio..
Mine turns on as soon as I plug in the batteries and if you turn it off it turns back on. I tried flashing the latest software and cleaning the power buttons but it still turns on by itself... very annoying especially if you forget to remove the batteries when you want to store the radio.
I'd contact the vendor that sounds faulty..
Painless360 thanks I will it's a shame because i found it to be very comfortable and good.
I have assigned vrA/vrB to control pitch and rudder of a camera gimbal, but since those are self-centering, the gimbal always returns to it's starting position when I leave the vrA/vrB sticks. Is there any way I could control gimbal, without having to continuously have my finger to vrA/vrB analogs?
+Geo Nik not sure, I'd ask the HobbyKing support team.. best of luck!
Take out the springs in the vrA and vrB wheels
does it have the function for servo delay for retracts?
I no have the radio to look. Best of luck
Hello sir i had f450 setup with naza m lite and flysky fs i6s ,i have issue when i arm my quad i face issue after throttle is zero my quad motor still working they not stop. What i need to do
I am not familiar with that flight controller. I'd check the minimum throttle setting or see if there is a setting that stops the rotors at zero throttle. Best of luck! !
Does this radio support receiving information from the model like altitude or battery left?
Yes, it does have telemetry..
I might have missed it. Is there a video how to set that up?
Not on our channel - yet..
I'd vote for that video. 😀
Could you explain what the flymode function is and what it does? Thanks:)
Check out the playlist for this radio ;) th-cam.com/video/l-OTKBzThPs/w-d-xo.html
Private video. :(
No its not
Andor Dávoti i.imgur.com/uyTKeOW.png
Yeah i know, but it wasnt private yesterday...
Where's the video on the upper corner rotary dials?
Those controls dot have ant special functions and are assigned to the outputs just like any of the others. No video specifically on them. Why do you ask?
I was wondering if I could use them on a 2-axis camera gimbal one for up/down and the other left/right.
I bought one of these radios (it won't be here for another month) and I'll be using it on a Naze32 FC in 450mm quad. Basically building a quad exactly like you told us in all your earlier videos.
Can you set-up dual rates to to toggle on a stick position, i cant figure out how to configure this
No need to post twice - I've answered this on your first post. Best of luck!
Which range this transimeeter?
Depends. Google 'how far can I fly painless360' to find my video on it.
can we do Aileron mixing for rc plane with this
Not easily, there is a mix function in the menu but the lack of trim tabs also mean that it's less than ideal. I'd look at another radio with mixes for planes and trim tabs if you're into fixed wing. I'm a huge fan of the FrSky Q X7 personally..
do u know any other 10 channel transmitter at the same price as fs i6s
Not personally. I'd look at what HK and BG are listing..
Can you reset your trims
Yes
Hi, can I install a helicopter on this radio? Thank you.
Only if you don't need things like swash mixes (i.e. using a flybarless controller on the Heli)..
So, you mean, it will work with 3Gx or CopterX? How one can setup it?
And the usual one with flybar will not work?
th-cam.com/video/u-NykZnjRM0/w-d-xo.html may be worth a look now.. Best of luck!
Help me
Do what??
I need to setup back my turnigy 9x... is it u have fb?
Sorry, we don't have that radio. Best of luck!