My 2012 I got in 2019 with only 56,000 on her at at 85-90k miles she decided to eat the hub bearings and yes I checked my tie rods and lower ball joints…rock solid. right rear and the two months later the left front started to make a noise and then the right front started to make noise … The right rear is original knock on wood lol Love the Taurus!! Not saying it’s earth shattering perfect but it’s been reliable to me and for me. I hope to get 200k out of her
If you are experiencing this noise please get it repaired! My whole wheel fell off my Taurus while driving due to this very problem. Control arm broke as well as the axle and bracket that mounts it all to the frame I ignored the clunking noise for just a little too long and it costs me a bunch of money plus a major headache
Thank you for the video. I lightly did the pry bar test on every joint on both sides and couldn’t find any play. But will feeling the links by hand I. Priced that I could pivot the drivers side one VERY easily. So I tore it down and once disconnected from the strut and sway bar. The bottom joint of the link had play. I changed both sides and the ride is quiet as can be. Amazing such a small issue could make so much noise
Awesome suggestions. I've got the same thing with my 2010 SHO w/ 97k. I was going to replace just about everything under there but this gives me a solid direction to look at.
Hi Brett, good video. I still have a ball joint tool in my main toolbox. Haven't used it in years. We got a recall on our Hyundai on the antilock sensor. Going to schedule it here soon
After watching this video and the other for the sway bar links I think I might be getting closer to figuring out what’s making this noise when I go over rough roads or potholes. It sounds like a bag of quarters or a noisy bed. I’ve taken it to two Ford dealerships and they can’t diagnose the issue.
Control arm bushing looks cooked for sure, but if you're checking your seat bar links do it on the ground, in the air puts too much pressure on them and hard to find play
I am very glad you put this video on I just bought a 2015 all wheel drive police Interceptor and for what I know it was built heavy duty , would I have the same problem ? 137,000.miles thank you.
When I turn my 2018 SHO on it makes a rattling/knocking noise for a few seconds then stops. Sometimes it does it when it turns on sometimes it doesn’t.
It’s not that part it’s the inner ball joint /inner tie rod link had same issue that part is suppose to have play but the wheel movement is from the rod you took that off of I know it’s probably fixed by now just a little info on the subject
My 22014 Taurus does a very similar thing. When I start driving, the clunk/rattling starts between speed 20mph and 35mph. It will be gone when the speed goes up, typically while it goes on the highway. The seller said they had the strut replaced but obviously it didn't help. Any thoughts, please? Thanks!
thanks man i just replace my two front struts it is my daughters car 2011 SEL and have the same clubbing noise coming from the front end on both side she has this car for a couple years Somebody had told her that it was her Struts so I brought new ones Replaced and did not illuminate the problem so my next project will be looking at a tire rod end and sway bar link and maybe the control arm bushing
YOU JUST DON'T CHANGE THE BUSHINGS YOU CHANGE THE WHOLE CONTROL ARM, THAT'S WHAT THAT IS CALLED THE CONTROLLER AND IT COMES WITH THE BALL JOINT INSTALLED AND YOU CAN FIND THEM ON ROCKAUTO DIRT CHEAP TRY TO ALWAYS GET THE MOOG BRAND.
My 2010 ford taurus sel awd 163,000kms on it. It makes a creaking noise when take off, sometimes makes the noise when driving and giving it gas. Any clues or tips please.
I just bought a 2014 Taurus SEL and I noticed on the highway it does start to make a slight knocking sound when I'm driving past 50mpg. I'm still trying to figure out what it could be
I have a 2014 TAURUS SE and it makes terrible road noise and feels like vibration in the steering wheel and cabin. My guess is it’s either front wheel hubs or needs tire balancing. Wheel hubs are expensive per side!!
If it make the noise and vibration without pulling to one side or the other I'd say you're on the right track. There are a few good videos with tips and tricks to getting hub assemblies off. Not the cheapest but can get off rock Auto if you're ambitious enough!
Hey I got a knocking Noise coming from the front. I replace the sway bar bushing, sway bars , control arm, ball joint on the left side also replace the two front struts. Wheel bearing on the front as well the inner and outer tie rod as well. It only happens when I’m going bumps more then 20 mph. But every time I move the car left and right while driving at low speed you could hear the Clunk noise coming the front. Can anyone help me??
Any ideas why a 2015 Ford Taurus SHO (awd) would grind and squeak ONLY backing while turning. I replaced both front end cb axles and problem still persists. It’s a shop right now.
them sway bar links always wear out at the connection. you can't see it when disassembled. shitty design. wrap the threaded shaft at it's base with electrical tape to take up the slack. top and bottom ends.
I have a 2012 Ford Taurus just replaced the struts and sway bar links on both sides. Still making a noise when I go over bumps in the front. Any ideas?
WHAT IS YOUR ISSUE I'M A MASTER MECHANIC FOR 30 YEARS AND IF YOU CAN JUST GIVE ME A SHORT OR SOMEWHAT SHORT EXPLANATION AS TO WHAT'S GOING ON WITH YOUR VEHICLE
Nice find! Sometimes a knock or shimmy in the front axle assembles can be misleading as far as symptoms. I'm glad that worked out!
My 2012 I got in 2019 with only 56,000 on her at at 85-90k miles she decided to eat the hub bearings and yes I checked my tie rods and lower ball joints…rock solid.
right rear and the two months later the left front started to make a noise and then the right front started to make noise …
The right rear is original knock on wood lol
Love the Taurus!! Not saying it’s earth shattering perfect but it’s been reliable to me and for me.
I hope to get 200k out of her
If you are experiencing this noise please get it repaired! My whole wheel fell off my Taurus while driving due to this very problem. Control arm broke as well as the axle and bracket that mounts it all to the frame
I ignored the clunking noise for just a little too long and it costs me a bunch of money plus a major headache
Thank you for the video. I lightly did the pry bar test on every joint on both sides and couldn’t find any play.
But will feeling the links by hand I. Priced that I could pivot the drivers side one VERY easily.
So I tore it down and once disconnected from the strut and sway bar. The bottom joint of the link had play. I changed both sides and the ride is quiet as can be.
Amazing such a small issue could make so much noise
Awesome suggestions. I've got the same thing with my 2010 SHO w/ 97k. I was going to replace just about everything under there but this gives me a solid direction to look at.
Hi Brett, good video. I still have a ball joint tool in my main toolbox. Haven't used it in years. We got a recall on our Hyundai on the antilock sensor. Going to schedule it here soon
After watching this video and the other for the sway bar links I think I might be getting closer to figuring out what’s making this noise when I go over rough roads or potholes. It sounds like a bag of quarters or a noisy bed. I’ve taken it to two Ford dealerships and they can’t diagnose the issue.
Nice video you help me a lot, I'm working on my 02 Taurus
Very important to put the year of the vehicle in the description
Thank you for the video, I think I am getting a 2014 Taurus Limited that has this issue. It has around the same mileage. I will for sure look at this!
Control arm bushing looks cooked for sure, but if you're checking your seat bar links do it on the ground, in the air puts too much pressure on them and hard to find play
Good Job . Process Of illumination is always wise ! Thanks For The Heads up .
2011 Ford Taurus Limited. I’ve had new struts put in, wave bar and tie rods. Still clunks. 88K miles
Ball joint possibly?
Good job. Very detailed. Thanks.
I am very glad you put this video on I just bought a 2015 all wheel drive police Interceptor and for what I know it was built heavy duty , would I have the same problem ? 137,000.miles thank you.
It's very possible.
I have been using it for five years. Why does the sound come from the right side of the front when the accelerator is given?
Motor mounts the rubber the motor sits on
Thank you this helped me out a lot
Sway bar links have to come off to see if bad, you cannot tell when they are on.
WIGGLES SIDE-2-SIDE(3&9oCLOCK)=TIE ROD END
WIGGLES TOP-2-BOTTOM(12&6oCLOCK)=BALL JOINT
Top to bottom can also be bearing
My 2014 fpis steering wheel grinds when turning and is shaking when driving. Thinking of replacing the cv axles. Any advice or opinions?
When I turn my 2018 SHO on it makes a rattling/knocking noise for a few seconds then stops. Sometimes it does it when it turns on sometimes it doesn’t.
It’s the lower motor mount for the torque
Could be also axle or struts
It’s not that part it’s the inner ball joint /inner tie rod link had same issue that part is suppose to have play but the wheel movement is from the rod you took that off of I know it’s probably fixed by now just a little info on the subject
My 22014 Taurus does a very similar thing. When I start driving, the clunk/rattling starts between speed 20mph and 35mph. It will be gone when the speed goes up, typically while it goes on the highway. The seller said they had the strut replaced but obviously it didn't help. Any thoughts, please? Thanks!
I always start with sway bar links, then tie rod ends. You can typically pop them out and see how they feel before you buy new stuff.
thanks man i just replace my two front struts it is my daughters car 2011 SEL and have the same clubbing noise coming from the front end on both side she has this car for a couple years Somebody had told her that it was her Struts so I brought new ones Replaced and did not illuminate the problem so my next project will be looking at a tire rod end and sway bar link and maybe the control arm bushing
A lot of times on these cars it is the drive axles, or the body bushings in the front also known as frame bushings
*Nice fix wonder if my a arm bushings are shot on my car also. Not a bad beater* #WorldsOkayestFarmer
YOU JUST DON'T CHANGE THE BUSHINGS YOU CHANGE THE WHOLE CONTROL ARM, THAT'S WHAT THAT IS CALLED THE CONTROLLER AND IT COMES WITH THE BALL JOINT INSTALLED AND YOU CAN FIND THEM ON ROCKAUTO DIRT CHEAP TRY TO ALWAYS GET THE MOOG BRAND.
Ball joints are built into the control arm
My 2010 ford taurus sel awd 163,000kms on it. It makes a creaking noise when take off, sometimes makes the noise when driving and giving it gas. Any clues or tips please.
Guess not
Sway bar link same problem as my car
I just bought a 2014 Taurus SEL and I noticed on the highway it does start to make a slight knocking sound when I'm driving past 50mpg. I'm still trying to figure out what it could be
Maybe cv axel/halfshaft. Does the knock slow down with speed?
You need to jack under your lower control arm to properly check ball joints
Yeah he was checking it wrong.
I have a 2014 TAURUS SE and it makes terrible road noise and feels like vibration in the steering wheel and cabin. My guess is it’s either front wheel hubs or needs tire balancing. Wheel hubs are expensive per side!!
They sure are. I was really suprised how expensive they were.
They're not nat on Rockauto
If it make the noise and vibration without pulling to one side or the other I'd say you're on the right track. There are a few good videos with tips and tricks to getting hub assemblies off. Not the cheapest but can get off rock Auto if you're ambitious enough!
Hey I got a knocking Noise coming from the front. I replace the sway bar bushing, sway bars , control arm, ball joint on the left side also replace the two front struts. Wheel bearing on the front as well the inner and outer tie rod as well. It only happens when I’m going bumps more then 20 mph. But every time I move the car left and right while driving at low speed you could hear the Clunk noise coming the front. Can anyone help me??
I have the same issue
Mines doing that to
Any fix for the clunk ?
WOW!! replaced all of that and still didn't fix the noise??
Same issue 06bford five hundred
My ‘13 SHO started to rattle and vibrate when I accelerate or turn the wheel to the right🤷♂️
Is it awd?
IF YOU HAVE A 13 SHO YOU SHOULD CHECK THE FRONT AXLES THAT IS A PERFECT INDICATOR OF THEM BEING BAD
Any ideas why a 2015 Ford Taurus SHO (awd) would grind and squeak ONLY backing while turning. I replaced both front end cb axles and problem still persists. It’s a shop right now.
I have this problem ! Did you figure it out ?
Sway bar link
They felt tight.
them sway bar links always wear out at the connection. you can't see it when disassembled. shitty design. wrap the threaded shaft at it's base with electrical tape to take up the slack. top and bottom ends.
I have a 2012 Ford Taurus just replaced the struts and sway bar links on both sides. Still making a noise when I go over bumps in the front. Any ideas?
Pretty much the only things left are tie rod ends or ball joints. How many miles?
142,000 miles
It’s more of a rattling sound when hitting a bump. If we had smooth roads I wouldn’t hear a thing.
@@samantharudloff8402 I would look at ball joints and tie rod ends for sure then.
Would the CV joint make noise
Hey i really can use ur help i have a 2013 Ford Taurus is there a way we can talk over the phone ?
WHAT IS YOUR ISSUE I'M A MASTER MECHANIC FOR 30 YEARS AND IF YOU CAN JUST GIVE ME A SHORT OR SOMEWHAT SHORT EXPLANATION AS TO WHAT'S GOING ON WITH YOUR VEHICLE
One of the many reasons Not to buy a Northern car - rust....
I have a 2014 Taurus and when I turn my wheel all the way to left or right it does a clicking noise. What do you think that is?
Probably a axle shaft, the u joints going bad.
Could be shock plates/mounts same thing happened to me.
@@bucksgarage1 if it clicks while driving cv/axel shaft. If it clicks while sitting still it's probably just strut mounts.
My 2013 does this clicking/groaning sound more so when turning hard right. Going to have it looked at I guess.
Don't sleep on those lower control arm bushing/dampener
Dude, them sway bar links are fucking shit and I can not find a better version, i'll try tie rod end now!
What year is your Ford Taurus & is it SE SEL or Limited
13 sel 115000 miles
You should finish insulating your garage and put drywall.
You should Venmo him $ for that 👏🏽👏🏽🤑 that would be super encouraging I am sure
@@RicardoPicena 🤣👍🏻
Petty