I have to give you a huge thank you, you saved my ass. I followed your instructions and everything worked except the motor would stop when I let go of the button. I noticed you were using momentary switches like mine so I re-watched your video and realised I had forgotten to program the PO-11, so I did that and it all works perfectly now. I’m so happy. Now I switch a big master switch and the VFD turns on and the original power lamp on the front of the lathe lights up to let me know there is power to the lathe. The original on / off switches also work too so it’s hard to tell there is even a VFD there. Thank you so much for your easy to follow and well explained video. Cheers mate, Stuart 🇦🇺
I thought i had it figured out but the programing far is what i couldn't get right. Even though the VFD stats rpm or hz i change it to. When i adjust it, the speed never changed on motor. I hate these kind of vfd where the programing is very hard to understand and get right
Not this model but a cheap VEVOR one , I did exactly what you said. Potentiometer for changing speed’s. But programming and understanding/fluking the pin out and setup to get it working. Can be done though
I have to give you a huge thank you, you saved my ass. I followed your instructions and everything worked except the motor would stop when I let go of the button. I noticed you were using momentary switches like mine so I re-watched your video and realised I had forgotten to program the PO-11, so I did that and it all works perfectly now. I’m so happy. Now I switch a big master switch and the VFD turns on and the original power lamp on the front of the lathe lights up to let me know there is power to the lathe. The original on / off switches also work too so it’s hard to tell there is even a VFD there. Thank you so much for your easy to follow and well explained video. Cheers mate, Stuart 🇦🇺
Thank you for explaining this setup. It has helped me a lot. 👍
You are an amazing teacher! Thank you
Thanks for knowgable video sharing.
Amazing video. Thanks a lot for the info; it was crystal clear!
Thank you the explanation is clear sir.
Many thanks for your useful information and good videos
thank you nice video keep it up
Thank you very much sir!
Thank you! The RUN button is NO and STOP button is NC
Very well explained.
Very well explained
You are a great teacher
நன்றி.
Helpful video
good job
Good job
Great explain sir
Single phase connection running 3 phase Gear Motor possible please reply
super explanation, but one thing i m not clear, how do you know if is three wire control or two? thx!
Hi! You use the NC or NO for both start and finish?
Hi i have a motor from eurodrive and this is 3 phase i already put the plates in the motor to Delta do i only need to install it on the VFD then?
How about using potentiometer to regulate speed of motor?
I thought i had it figured out but the programing far is what i couldn't get right. Even though the VFD stats rpm or hz i change it to. When i adjust it, the speed never changed on motor. I hate these kind of vfd where the programing is very hard to understand and get right
Not this model but a cheap VEVOR one , I did exactly what you said. Potentiometer for changing speed’s.
But programming and understanding/fluking the pin out and setup to get it working.
Can be done though
Thanks . can you please make available the circuit diagram
One comment:
Start button should be NO (normally open).
Stop button should be NC (normally closed).
Good one
Thanks
Please do one with a outside rehestat along with a push button to start.
Good videos
hi sir in an application with start stop of 3 phase motor what is the best way to connect it so the motoer is not hot
the triangle or the star ?
Hello sir your video is very helpfull sir may i ask how many KW of vfd i need to use my 3phase motor 220v 2.5hp and 220v supply thank you
you will have a label but if you are telling 2.5hp i think above 1.5kw so 2.2kw will be enough for you
Is there Any recommended speed for a 3 face motor for a York Pack unit ?
Thank
can you pls explain the same on/off control with only one 24V PNP proximity sensor?
Jak wyświetlić na tym wyświetlaczu obroty w jednostkach rpm zamiast Hz
it need a wiring diagram for a beginner to understand
Can you help me to display a rpm ?????? Thanks in advance
Hi, Can i know the output of motor is in star or delta
How many hp does a vfd can operate? Is this applicable to large motors?
Super
Nice
what is ratting of this vfd..
How can I use Dc to control a 3 phase induction motor?
Share the link for two wire connection
He did. It’s at the bottom of the description.
Help me to programing the vfd
What is v f d in electrical
How to reset alll settings.. i think i mess up
Anna siemens tell me
Where is the overload relay?
❤
Waters Knolls
Bro Ths MFD prise ?
Zieme Lights
Hane Path
Ratke Hills
Althea Creek
Mitchel Path
Cummings Village
Jayce Station
Grant Streets
Cordia Road
Braun Summit
Lucy Fields
Runte Circle
Oh you dont say torque of the motor depends on magnetic field density and current , and speed depends on the frequency . You dont say .
Cummerata Expressway
West Fort
Kris Station
Upton Views
Fannie Turnpike
Brennan Centers
Oran Junction
Wunsch River
Where’s the input voltage earth???
Abshire Drives
Where are the earth's?
Rowe Valleys
Emard Valleys
Jessie Dale
Speak in to Urdu & hindi
Hindi in
watch on this channel www.youtube.com/@ElectricalTechnician
Hey electrical guy, I had a technician wire my 4kw inverter to a toilet paper but when I put speed on 1.5 the machine runs too fast
4493 Jerel Plains
74477 Fredy Loaf
81986 Graciela Street