Love your content! FYI I recently put just a male connector to all my guns and assembled an all-in-one filter/regulator with a female adapter so I only need one because I used to try to put a filter and regulator on every gun.
Hey Pete. I have a tough one, I am painting a back quarter panel and there is not break line. it goes quarter to roof to other quarter, the paint is pretty new and looks good, I am scared of using blender on the clear because of durability, I can blend it in the jamb and probably be ok or is there a better way? thanks !!
Thank you Pete. I've been Painting ( mostly Industrial Spray painting) since 1986. And you are 100 percent Correct. God bless you. Most people don't believe me when I preach to them, that the Air Supply Chain is one of,if not The Main Culprit of Paint Problems. Thanks again brother.
I say the same and people constantly argue with me about having a high quality separator at the compressor. Well I have a high quality one there and a secondary one at my hook up point and I still run one at the gun because of 30' of hose. Mostly guys in the fire arm cerekoting industry like to try to say it's unnecessary and makes the gun heavy. If I as a man was restricted by the 6 ounces added by a filter at my gun then I have a real problem to where I would have to make sure my balls were not missing.
Harbor Freight also sells a gun filter with the beads. I have found you can actually take it apart, put the beads in the oven, turn them back to purple, assemble and use again. Phillip Hall
@@ericschulze5641 At 350 degrees, it gets the job done, lol. After going through all the filtertation that Pete has and most painters have, very little, 'if any' oil gets to the gun. This good little device shown by Pete is a good insurance policy (just in case).
Thanks My friend Pete ! I just bought a two pack of these on Amazon for $18.89 so they have gone up about a dollar each in price since you bought yours.
Hey, I just wanted to say thank you for all your hard work in putting these videos for us to learn from! I have learned a ton from your videos and have painted 1 motorcycle and 2 cars. It is a ton of fun ! Thank you pete !
One of the most useful videos yet Pete! Do you have a video on how you match up or blend areas painted like the engine compartment separately and late paint the exterior of the car? If you have a video on how to make and setup hoods, fenders and doors on hangers that would be great. I’d like to know the best ways to paint the inner doors jams, engine compartment, trunk etc and later the exterior. If of course that’s your preference. Thanks for the great advice. Sub here.
🤔I used 50 ft of 3/4 in stainless steel pipe straight up straight down back straight up straight down and then my filters and oil separator and my paint comes up purpley smooth no fish eyes beautiful paint job I do use a another 50 ft of copper teething in a freezer Locker to run my air through takes the moisture out of any Air you're right about that filter connected to the paint gun
Hello Pete my friend Pete thank you so much for all your tips and videos and teaching we just had to rework on my wife's new race car let's just say it got scratched before even hit the damn track so a buddy of mine he was able to paint it before he left but nobody around I had to do it and I used one of my dad's old Binks guns and I developers what model number they are I don't know I took them uptown got to rebuild kit and rebuild them they worked perfect and it was a off shade of plum crazy purple was the color of her race car and black thank you so much it turned out beautiful
I use to be subscribed to your channel but I didn't like the language you used. I am a Born Again Christian and it bothered m. Well today I happened on your video about gun filters. I noticed a Gospel song at the opening of your video and was surprised. Then I noticed no foul language. I don't know if you got saved or what has happened but I enjoyed your video. I'm once again going to subscribe to your channel. I look forward to more of your lessons. I'm wishing you and your family a Blessed Day. God is Good
@@not2late2game53 I was overcome by his video that I wrote that close to the end. Then I continued to finish it and was very disappointed. My bad. And yes we agree God is Good
Great video Pete good information I used some Neko air filters but they don't tell me when they're letting the oil and water through the line thanks a lot
Great tip Pete. And there's all the "experts" from the forums that are installing automobile AC condensers to their compressor systems and building copper-tubing air dryers. I think this is totally unnecessary.
I use these filters. Once they turn pink, I take them apart and dump the desiccant out on a paper plate and zap it in the microwave until it returns to the blue/purple color. Once it cools, I put it all back together and reinstall the plugs until next use.
So you are able to just clean the filter and its good to use again or just replace it? I got one with a little pin under which i can push in idk what its for but its a NEIKO filter from amazon it was like 11 bucks. NEIKO 30252A Water and Oil Separator
regarding the orange trap,, they peel bad inside a friend said he had to replace one so epoxy primmed the inside of the new one,, He puts the stainless steel pot scrubber wool he gets at Dollar general inside so the water condenses on the wool before it can move down stream
I not sure I understand what you are saying. Are you saying he takes the filter apart, removes the purple beads, coats the inside of the filter housing with epoxy and puts it back together, but uses the stainless steel wool instead of the beads? Thanks, Phillip Hall
Used one of those orange in color with beads in the past the exact type and it exploded while shooting clear. You pretty much know what happen to the paint job after that happened.
Pete, after putting the Epoxy Sealer on the car, do i need to scuff it if the Sealer is left to fully cure? As you've said don't sand it, yet there's nothing for the paint to key on to.
Once i sprayed primer here thry say instant primer and after sanding it many micro pores or holes apeard. I don't know whats the problem. But i thought maybe the primer drys more quickly than the thinner in it and the thinner got trapped under the primer and make thise tiny bubbles so when i sanding it they will apear. And be visible. So i decided to spray narrow layers on it to solve the problem. Am i right or it's because of something else? Am i right
Hey Pete love the vids been a long time watcher. Iam confused about sealer before paint. Can you recommend a good sealer I am using the U pol primer you recommended in another video. Thanks man.
Hi Pete, why black pipe for your air supply? It will rust internally from moisture and will eventually clog your $200 regulator. Plastic or copper lines are much better choices to avoid this.
There shouldnt be any oil coming outta your compressor if you have an oil descate filter before your air dryer i still use one i have the devbiss qc3 regulator with another decate bead my speed aire dryer quit bought a new smc 25 cfm dryer coming i refuse to primer or paint with out a dryer
Hey, If you remove your hockey mask covered in seaweed, you can see that your filter changed colors a couple of years ago! Not a paint gun, just the air nozzle you use on your blow-up dolls. Do you have a video on your blow-up doll collection? Creepy!
Bro, please stop yelling.. your giving good info but your literally yelling it at me and there is no need.. just some constructive criticism, take it or leave it...
![Should I [SANDBLAST] My Car ? How To Remove Old Paint!](http://i.ytimg.com/vi/R9eA3tJN6ek/mqdefault.jpg)
Time to get rid of that oil and water in our paint jobs -- here's how we're gonna do it... Thanks for watching..
Love your content! FYI I recently put just a male connector to all my guns and assembled an all-in-one filter/regulator with a female adapter so I only need one because I used to try to put a filter and regulator on every gun.
Pete, where can I order the matrix mp3?
Hey Pete. I have a tough one, I am painting a back quarter panel and there is not break line. it goes quarter to roof to other quarter, the paint is pretty new and looks good, I am scared of using blender on the clear because of durability, I can blend it in the jamb and probably be ok or is there a better way? thanks !!
Pete knows his shit. He’s been doing it for a long time.
Thank you Pete. I've been Painting ( mostly Industrial Spray painting) since 1986. And you are 100 percent Correct. God bless you. Most people don't believe me when I preach to them, that the Air Supply Chain is one of,if not The Main Culprit of Paint Problems. Thanks again brother.
I say the same and people constantly argue with me about having a high quality separator at the compressor. Well I have a high quality one there and a secondary one at my hook up point and I still run one at the gun because of 30' of hose. Mostly guys in the fire arm cerekoting industry like to try to say it's unnecessary and makes the gun heavy. If I as a man was restricted by the 6 ounces added by a filter at my gun then I have a real problem to where I would have to make sure my balls were not missing.
Harbor Freight also sells a gun filter with the beads. I have found you can actually take it apart, put the beads in the oven, turn them back to purple, assemble and use again. Phillip Hall
That doesn't get the oil out
@@ericschulze5641
At 350 degrees, it gets the job done, lol. After going through all the filtertation that Pete has and most painters have, very little, 'if any' oil gets to the gun. This good little device shown by Pete is a good insurance policy (just in case).
read you shouldn't reuse the beads because they pick up other debris that can't be cleaned.
@@chvydrptop
Water//Air separation is the goal for me.. And I have had no problems with this....
Pete, I Liked the opening tune, "Leaning On The Everlasting Arms" Phillip Hall
Thanks My friend Pete ! I just bought a two pack of these on Amazon for $18.89 so they have gone up about a dollar each in price since you bought yours.
Thanks pete! I know you don't like Amazon, but after watching i found and ordered some. 2 packs for $22
Hey, I just wanted to say thank you for all your hard work in putting these videos for us to learn from! I have learned a ton from your videos and have painted 1 motorcycle and 2 cars. It is a ton of fun ! Thank you pete !
Leaning, Leaning,....Leaning on the ever lasting arms......Good song Pete.
I noticed that too and commented..
That song used in the true grit remake, awesome slow version, just beautiful.
Those work good Pete. I use the Motor Guard "toilet paper" filter where my hose plugs into the hard line also.
Thanks Pete.
I think you have drilled this information into my brain. Thank you.
Pete this is the best video ever. No one has given this advice. thanks man
Thanks Pete! Always trying to help us get the job done right. Tell Minnie I said HI!
One of the most useful videos yet Pete!
Do you have a video on how you match up or blend areas painted like the engine compartment separately and late paint the exterior of the car? If you have a video on how to make and setup hoods, fenders and doors on hangers that would be great. I’d like to know the best ways to paint the inner doors jams, engine compartment, trunk etc and later the exterior. If of course that’s your preference. Thanks for the great advice. Sub here.
The Fisheye Filter ( that’s the brand name) are hands down the best. They are expensive but nothing beats them.
Heck ya good job pete listen learn
Amen to that Pete, that’s the main reason for most painting problems 😎😎👍👍👍🤗🤗🍮🍮
🤔I used 50 ft of 3/4 in stainless steel pipe straight up straight down back straight up straight down and then my filters and oil separator and my paint comes up purpley smooth no fish eyes beautiful paint job I do use a another 50 ft of copper teething in a freezer Locker to run my air through takes the moisture out of any Air you're right about that filter connected to the paint gun
Thats rite pete telling how you really feel
Hello Pete my friend Pete thank you so much for all your tips and videos and teaching we just had to rework on my wife's new race car let's just say it got scratched before even hit the damn track so a buddy of mine he was able to paint it before he left but nobody around I had to do it and I used one of my dad's old Binks guns and I developers what model number they are I don't know I took them uptown got to rebuild kit and rebuild them they worked perfect and it was a off shade of plum crazy purple was the color of her race car and black thank you so much it turned out beautiful
I use to be subscribed to your channel but I didn't like the language you used. I am a Born Again Christian and it bothered m. Well today I happened on your video about gun filters. I noticed a Gospel song at the opening of your video and was surprised. Then I noticed no foul language. I don't know if you got saved or what has happened but I enjoyed your video. I'm once again going to subscribe to your channel. I look forward to more of your lessons. I'm wishing you and your family a Blessed Day. God is Good
It's good you didn't listen to the end. He really is a Good God
@@not2late2game53 I was overcome by his video that I wrote that close to the end. Then I continued to finish it and was very disappointed. My bad. And yes we agree God is Good
Thank you Pete God bless 🙏🏻🇦🇺
What devilbiss air filter model did u show post on the wall please thanks for the information in advance
Thanks Pete. I don't know if those ate available instead UK yet, and I bet they'll cost 4x more here, but I'll get one.
Thanks for sharing your knowledge 🙏
Common sense is not so common anymore. Good video
Great video Pete good information I used some Neko air filters but they don't tell me when they're letting the oil and water through the line thanks a lot
Lenn on the ever lasting arms tatol first class
Excellent tip! Thanks, Pete!
You know what your talking about thank you sir
Great tip Pete. And there's all the "experts" from the forums that are installing automobile AC condensers to their compressor systems and building copper-tubing air dryers. I think this is totally unnecessary.
I use these filters. Once they turn pink, I take them apart and dump the desiccant out on a paper plate and zap it in the microwave until it returns to the blue/purple color. Once it cools, I put it all back together and reinstall the plugs until next use.
So you are able to just clean the filter and its good to use again or just replace it? I got one with a little pin under which i can push in idk what its for but its a NEIKO filter from amazon it was like 11 bucks. NEIKO 30252A Water and Oil Separator
Great information, saved this video
what tips size you are using for prime and what size for paint thanks pete other wise i ask mini
Thank you for the tip and info 😁😎
I'm gonna change Pete. I use the cheapo ball filter but this one sure looks better! Thanks Pete!
regarding the orange trap,, they peel bad inside a friend said he had to replace one so epoxy primmed the inside of the new one,, He puts the stainless steel pot scrubber wool he gets at Dollar general inside so the water condenses on the wool before it can move down stream
I not sure I understand what you are saying. Are you saying he takes the filter apart, removes the purple beads, coats the inside of the filter housing with epoxy and puts it back together, but uses the stainless steel wool instead of the beads? Thanks, Phillip Hall
@@PhillipHall01orange one the wall filter, its hollow the powder coating inside peels and corrodes, so sooner you deal with it you can stop it
@@91rss
👍🏻
Hello Pete.
Hey RAY! Thanks for watching
Used one of those orange in color with beads in the past the exact type and it exploded while shooting clear. You pretty much know what happen to the paint job after that happened.
Thanks for the information
Pete, after putting the Epoxy Sealer on the car, do i need to scuff it if the Sealer is left to fully cure? As you've said don't sand it, yet there's nothing for the paint to key on to.
What's the part number ? (Thanks for YOUR service as well!)
Good information,and encouragement to use the Dryer Filter thanks
Pete are you spraying any water-borne?
Once i sprayed primer here thry say instant primer and after sanding it many micro pores or holes apeard. I don't know whats the problem. But i thought maybe the primer drys more quickly than the thinner in it and the thinner got trapped under the primer and make thise tiny bubbles so when i sanding it they will apear. And be visible. So i decided to spray narrow layers on it to solve the problem.
Am i right or it's because of something else?
Am i right
Awesome video Pete. Always learning from you✌🏻🤘🏽✊🏾
Hey Pete love the vids been a long time watcher. Iam confused about sealer before paint. Can you recommend a good sealer I am using the U pol primer you recommended in another video. Thanks man.
Isn't the cheater valve the same as a regular with a gauge?
This is good cause I need to research how to set up my compressor. From start to finish.
What size fittings to use Pete??
www.tptools.com/tech-metal-piping.dlp
cached.tptools.com/Images/airline-piping-diagram.pdf
What model Developers wall mount filter?
Devilbiss
Air hose- 3/8 or 1/2 in. ?
.
Hi Pete, why black pipe for your air supply? It will rust internally from moisture and will eventually clog your $200 regulator. Plastic or copper lines are much better choices to avoid this.
Keep the valve closed on gun when not in use or moisture will attack the desicant before you can use it
Harbor freight has that filter and you can unscrew the top and refill it. 7.49$
item nbr 00261
There shouldnt be any oil coming outta your compressor if you have an oil descate filter before your air dryer i still use one i have the devbiss qc3 regulator with another decate bead my speed aire dryer quit bought a new smc 25 cfm dryer coming i refuse to primer or paint with out a dryer
My Friend Pete!
Should be on tge tank going into ANY airline
I like your work us old timers don't know anything like fuck
Never let the last few feet of your hose touch the floor. Or make sure you wipe it down good. #fod
👌👋👍
It's cheap insurance and most people won't spend the money to get them but spend thousands of dollars on the paint and supplies
👍😉
😊👋👋👍👍
$21 bucks on Amazon for two filters
My paint work is fantastic, BUT the Shtt Chinese made sold by Amazon is trash. O rings fell out, drips water onto just laid paint. 😡 Avoid the Junk
ABUSIVE PETE: "If you need color changing body filter the only dummy is you!"
ALSO ABUSIVE PETE: "You need color changing air filters!"
Hey, If you remove your hockey mask covered in seaweed, you can see that your filter changed colors a couple of years ago! Not a paint gun, just the air nozzle you use on your blow-up dolls.
Do you have a video on your blow-up doll collection? Creepy!
Why is it my Chinese made Amazon Y-Kinz spray gun LEAKS WATER onto my FrEaKiNg Work? 😡🤬
why you yelling bro? gaw damnn
Bro, please stop yelling.. your giving good info but your literally yelling it at me and there is no need.. just some constructive criticism, take it or leave it...
good content buy WHY the cursing buddy, very unnecessary.
All cussing needs to go.
👋ㅤ【C͟a͟n͟ ͟y͟o͟u͟ ͟p͟l͟e͟a͟s͟e͟ ͟r͟e͟a͟c͟t͟ ͟t͟o͟ ͟“͟T͟h͟e͟ ͟L͟a͟d͟y͟ ͟o͟f͟ ͟H͟e͟a͟v͟e͟n͟”͟ ͟f͟i͟l͟m͟ ͟T͟r͟a͟i͟l͟e͟r͟?】ㅤ
❤️❤️