This is such a detailed video and with so many configs! Really appreciate the hard work you put into this video and reassembling everything. Definitely subbed.
Hey ! Great video, thanks for showing many install options :) I have a matx board and a full size atx board, no gpu yet. Would the board and psu fit in there together ?
hi, do you mean matx board and atx psu? No, that's not compatible. You have to use SFX for MATX/ATX boards as the PSU will sit beside the board -- no space for a fatter PSU.
i was looking for a sff case that can fit my matx mobo and atx psu and found this video. have you tried that combo set up? did you encounter any issue with spacing?
@@manongunboxing it's videos like these that are really helpful. keep up the good work and thank you for reply and information! more power to your channel.
For s300, I'll think about it depending on the performance result of the s400 which will be out this Oct. For gigabyte lp 4060, it's likely a no at this point due to cost.
For one, I just followed the manual. 🙂 Other than that, it is too tight in my opinion as AIO tubes aren't that flexible. It will hit the PSU and riser. For ATX builds, you have no room at the bottom as well.
Hi, it depends on what GPU you have and where do you plan to install it (the where also depends on the size of the GPU). For rear install, I suggest getting a 400mm-440mm female reverse riser. For front install, I suggest getting a 280mm-300mm straight riser.
Hi. Ano po maaadvice nyo sakin, currently using asus ap201 case mAtx mobo w/ air cooler. Plan ko sana magpalit for ssupd ? Worth it po kaya? Or stick nalang sa ap201?
For me, if ang goal lang po is downsizing for the sake of it, not worth it until you need the space na maffree up. If space po ay major concern, then yes, downsizing is worth it. Nasa 33L po ang ap201 iirc… if maliit desk niyo, might be worth it. Otherwise, save money for actual pc parts na may tulong sa performance.
Around there talaga presyo ng PCIE riser na 4.0. Pero yung sa akin galing kay middle999 sa lazada. Sya yung seller ng PCCOOLER i100 Pro, nasa listing mismo ng i100 pro yung riser, check lang sa variations. That is for usual sandwich style cases pala sir ha not for Meshroom S. For Meshroom S, go to Pinklehub sa shopee, mas marami selection nila doon for some reason.
Hello, can I know if regualr power supply will fit in the case? I have a PC which: matx, rtx3080ti, 3fan radiator aio. I am hoping to install matx on the front side, with regular psu; and GPU with 3 fan radiator on the back. will this configuration possible? I would like to know the compatibility. I have not seen any demostration videos of them using matx and regular psu combo.
Matx and atx psu combination will not be compatible to Meshroom S. Atx psu will only be compatible with ITX mobo. Also 3-fan radiator AIO (360mm I assume) is also not compatible without the extension bracket. Hope this clarifies.
Extremely informative and i dare say the most detailed video about the case compared to the rest of guides i found so far regarding the meshilicious. Im thinking about getting this to downsize my current ATX build, but i have a massive gigabyte 4070ti master, is it safe to assume that i will have to opt for a low profile air cooler for the cpu base on your venn diagram ?
So much effort was placed into this video (especially the different configurations) keep up the good work!!
Fantastic video! I’m in Australia and love the fact you are testing at 26 degrees ambient. Much for realistic temperature results.
This is such a detailed video and with so many configs! Really appreciate the hard work you put into this video and reassembling everything. Definitely subbed.
Meshroom is such a great SFF case. Great compatibility and a very open design for cooling.
My man, I've been looking to downsize to my matx build to an SFF chassie. Thanks for the realistic insight!!
Very helpful vedios po lalo na if you really want detailed explanation if your planning to get into sff cases❤❤
Kamustaka!!
Hey ! Great video, thanks for showing many install options :) I have a matx board and a full size atx board, no gpu yet. Would the board and psu fit in there together ?
hi, do you mean matx board and atx psu? No, that's not compatible. You have to use SFX for MATX/ATX boards as the PSU will sit beside the board -- no space for a fatter PSU.
@@manongunboxing so would a SFX-L psu work with a matx board ?
Yes, it should be fine
mukhang pasok to sa sapphire rx6800xt ko a... 310mm.. worry ko nalang ung scythe big shuriken ko
i was looking for a sff case that can fit my matx mobo and atx psu and found this video. have you tried that combo set up? did you encounter any issue with spacing?
Hi, by spec, that combination is not compatible. The mobo would consume the space that would’ve been for the atx psu.
@@manongunboxing it's videos like these that are really helpful. keep up the good work and thank you for reply and information! more power to your channel.
another great sff case review! are you going to review the s300 itx case or the newly released gigabyte rtx 4060 low profile?
For s300, I'll think about it depending on the performance result of the s400 which will be out this Oct.
For gigabyte lp 4060, it's likely a no at this point due to cost.
is there anything stopping you from flipping the rad the other way and running the tubes up from under the motherboard?
For one, I just followed the manual. 🙂
Other than that, it is too tight in my opinion as AIO tubes aren't that flexible. It will hit the PSU and riser.
For ATX builds, you have no room at the bottom as well.
What gpu riser do you recommend with the atx built
Hi, it depends on what GPU you have and where do you plan to install it (the where also depends on the size of the GPU).
For rear install, I suggest getting a 400mm-440mm female reverse riser.
For front install, I suggest getting a 280mm-300mm straight riser.
Hi. Ano po maaadvice nyo sakin, currently using asus ap201 case mAtx mobo w/ air cooler. Plan ko sana magpalit for ssupd ? Worth it po kaya? Or stick nalang sa ap201?
For me, if ang goal lang po is downsizing for the sake of it, not worth it until you need the space na maffree up. If space po ay major concern, then yes, downsizing is worth it. Nasa 33L po ang ap201 iirc… if maliit desk niyo, might be worth it. Otherwise, save money for actual pc parts na may tulong sa performance.
@@manongunboxing thank you so much po
What brand sa shopee and lazada mare recommend mo na pcie riser na 4.0? Pricy kasi yung sa amazon na linkup mga 3k.
Around there talaga presyo ng PCIE riser na 4.0. Pero yung sa akin galing kay middle999 sa lazada. Sya yung seller ng PCCOOLER i100 Pro, nasa listing mismo ng i100 pro yung riser, check lang sa variations. That is for usual sandwich style cases pala sir ha not for Meshroom S. For Meshroom S, go to Pinklehub sa shopee, mas marami selection nila doon for some reason.
@@manongunboxing Makapal yung sa amazon worried na baka hindi bendable sa case. Mas mura tong sa lazada. Maraming salamat!
Hello, can I know if regualr power supply will fit in the case? I have a PC which: matx, rtx3080ti, 3fan radiator aio. I am hoping to install matx on the front side, with regular psu; and GPU with 3 fan radiator on the back. will this configuration possible? I would like to know the compatibility. I have not seen any demostration videos of them using matx and regular psu combo.
Matx and atx psu combination will not be compatible to Meshroom S. Atx psu will only be compatible with ITX mobo.
Also 3-fan radiator AIO (360mm I assume) is also not compatible without the extension bracket.
Hope this clarifies.
what fans were used for the cooler fans? Were they the original from the cpu cooler?
Yes, original from cpu cooler.
Atx board ko tuf x570 wifi kaya pa mag add ng 2x2.5" ssd if ever? Using psu sfx naman and Gpu is tuf 3070ti. Also using lian li Aio 240mm.
Di po compat components. Gpu too big tapos para makatabi ng aio together with atx mobo
Question do you think the ASRock X399M Taichi Micro atx will fit without issues and a rtx 3090ti FE with cpu AIO 240mm?
It can't. For matx, aio, and gpu to fit in, gpu width needs to be at most 120mm
@@manongunboxing so meaning i have to choose between the cpu cooler or the graphics card, but aside from that the board will fit right?
Yes, all correct.
matx with atx psu possible? 5700xt nitro gpu
No. For mATX, it will only be compatible with sfx psu
San mo to nabili?
Kay Gtek Computers sa Shopee po, search for Meshroom.
5:30 whaat problems did you face
It's the RAM. Just reseated.
So we can fit a matx 9.6x9.6 mb in it
Yes. Matx and even atx... But only with sfx psu and some other limitation
Extremely informative and i dare say the most detailed video about the case compared to the rest of guides i found so far regarding the meshilicious. Im thinking about getting this to downsize my current ATX build, but i have a massive gigabyte 4070ti master, is it safe to assume that i will have to opt for a low profile air cooler for the cpu base on your venn diagram ?
Yes.