Tinyhawk S and Freestyle | Bind in D16 Mode

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 133

  • @nickoncomputer9081
    @nickoncomputer9081 4 ปีที่แล้ว +16

    It's bind_rx not bind_rx_spi in latest version of betaflight

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +3

      Thank you for making note of this.

    • @nickoncomputer9081
      @nickoncomputer9081 4 ปีที่แล้ว +1

      Ian Beaty thank YOU for posting the video!

    • @TheTwistty1
      @TheTwistty1 3 ปีที่แล้ว

      I was getting an error msg with the bind rx spi

    • @afrog2666
      @afrog2666 ปีที่แล้ว

      OMG, you just saved me from pulling my hair out!

  • @greenfpv506
    @greenfpv506 4 ปีที่แล้ว +2

    I really wish i found this video a week ago im fairly new to the fpv part of drone flying so finding the right information not knowing much is a little rough. This video was clear and right to the point thank you !

  • @IanBeaty
    @IanBeaty  4 ปีที่แล้ว +12

    Here are the steps in the video written out:
    In Betaflight:
    Open Betaflight
    Plug USB cable into Tinyhawk
    Click "Connect" if Betaflight does not automatically connect
    Click "Configuration" tab
    Scroll to "Receiver" section
    "Receiver Mode" needs to be "SPI RX support"
    Change "SPI Bus Receiver Provider" from "FRSKY_D" (D8 mode) to "FRSKY_X" (D16 mode)
    Click "Save and Reboot"
    You might need to click "Disconnect" and then "Connect" and double check that "FRSKY_X" saved
    Click "CLI" tab
    Type "bind_rx_spi" to put receiver into bind mode
    On transmitter:
    Select the model for the Tinyhawk
    Go to "MODEL SETUP" page
    Scroll to "Mode" for the "Internal RF"
    Change "Mode" to "D16"
    Take note of "Receiver No."
    Move Tinyhawk and transmitter apart to prevent binding issues
    Select "[Bind]"
    Select "Ch1-8 Telem OFF"
    Stop binding in the transmitter
    In Betaflight:
    In "CLI" type "get frsky_x_rx_num"
    The "CLI" should say "frsky_x_rx_num = XX" where "XX" is the same as "Receiver No." on the transmitter and this shows it is bound correctly
    Type "save" into "CLI"
    Click "Disconnect" and unplug Tinyhawk
    Go fly!

  • @GarrettDespainVlog
    @GarrettDespainVlog 4 ปีที่แล้ว +1

    I love you. For those also searching, I was able to bind my Taranis Qx7 ACCESS to this setup, under the ACCST D16 setting. It took a long time. As of right now it's bound, but my receiver settings are all wonky. Working on fixing those.

    • @Wow88z
      @Wow88z 4 ปีที่แล้ว

      Can you describe what was “wonky” about your receiver settings? Once you bind in ACCST D16 mode was it able to fly ? I’m on the same boat as you with the QX7 ACCESS.

    • @Ebnis_Dener
      @Ebnis_Dener 4 ปีที่แล้ว

      Cosmic Scenes Are you able to bind the qx7 with the tinyhawk?

    • @Wow88z
      @Wow88z 4 ปีที่แล้ว

      Denis Ebner I don’t own the tinyhawk, I did a lot of research and If I was to get a micro quad I would get Beta75x or 85x. You can bind tinyhawk to QX7 through the CLI command in betaflight

  • @danielwagner4064
    @danielwagner4064 3 ปีที่แล้ว +3

    does this work if my taranis qx7 only has access and accst D16? I can't seem to get the controller to bind to my Tinyhawk 3

    • @mehican350
      @mehican350 ปีที่แล้ว

      did you ever figure this out?

  • @Reecefpv
    @Reecefpv 3 ปีที่แล้ว +1

    Iv been trying this but my rx num is just 00 it never chages. Driving me crazy lol this is the first time trying the internal tx module. I got it and started using crsf from the beginning.

  • @stevendawson4563
    @stevendawson4563 4 ปีที่แล้ว +1

    In the CLI tab I get an error message in red when I enter the code?

  • @Perforator2000
    @Perforator2000 4 ปีที่แล้ว +1

    I managed to bind my Tinyhawk Freestyle to my Taranis QX7 Access in ACCST D16 mode, but while flying it randomly failsafes and drops to the ground. I've discovered that other people have had that problem, but I haven't seen any solution to it. I have an XJT module and a regular non-Access QX7 transmitter on the way, so I hopefully will be able to fly it in D8 mode.

    • @GarrettDespainVlog
      @GarrettDespainVlog 4 ปีที่แล้ว +1

      Trying to bind mine now, and have been legit all day. What have you discovered?

  • @itsChinny
    @itsChinny 12 วันที่ผ่านมา

    I am having a issue binding my ELRS E8 and my Tinyhawk S. From my research, these should be compatible. Any tips or ideas? Struggling majorly and have no one for advice

  • @the73spit
    @the73spit 7 หลายเดือนก่อน

    This is not working for me in 2024...followed instructions exactly. it does not update the rx number in the CLI and I cant get it to bind to my taranis x9d.. any ideas?

  • @kingarthurmcguire5451
    @kingarthurmcguire5451 4 ปีที่แล้ว +2

    Thanks for this amazing video! Thought my Tinyhawk Freestyle was garbage with the new Taranis X9D+ SE 2019. You saved the day. Cheers!

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      So glad it helped!

  • @thomaskrogh2036
    @thomaskrogh2036 4 ปีที่แล้ว +1

    Hi Ian, Thanks for this well explained video.
    I'm trying to bind a Tinyhawk S with the Taranis X9 lite and it doesen't work. I do all the steps, but it won't bind and when I type in the "get frsky_x_rx_num" I get a 0 (zero) even though I'm not trying to bind to 0 (zero).
    Do I need another radio or what?
    Best, Thomas

    • @TheLoganatorz
      @TheLoganatorz 4 ปีที่แล้ว

      I was able to get the tiny hawk freestyle working with the x9 lite after following this. Keep at it, I’m sure there’s something in there keeping it from binding. I wish I could help but I’m new to fpv quads lol

    • @ericbridgeford1856
      @ericbridgeford1856 4 ปีที่แล้ว

      TheLoganatorz I’m currently struggling to connect my x9 lite to my tiny hawk freestyle

  • @bbauck10
    @bbauck10 4 ปีที่แล้ว

    Very helpful, first time I used cli to bind. Thanks for the video

  • @BlueOvals24
    @BlueOvals24 4 ปีที่แล้ว

    You sir are a life saver! Been spending an hour watching a video on how to bind on D8 but it wasn't working. One problem though, for some reason the sticks are inverted, right stick is throttle/yaw and left is pitch/roll. How do I set it the normal way? Nevermind that, I got it! But this video is the only reason my Tinyhawk S is bound to my Taranis Qx7 so for that, you earned a like and subscriber!

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Glad the video helped! Just a point of info since you already figured it out, you can switch your channels on your Taranis, or in Betaflight and it is fairly simple to do it in either place. Have fun flying!

  • @MSP106
    @MSP106 4 ปีที่แล้ว +6

    When typing bind_rx_spi getting an unknown error message. Followed all of the steps up until this point

    • @conormcnally8173
      @conormcnally8173 4 ปีที่แล้ว

      Yeah same, Is there anyway to fix this?

  • @aiming2high
    @aiming2high 5 ปีที่แล้ว

    what if the drone doesn't connect to betaflight?

  • @alexanderst5619
    @alexanderst5619 5 ปีที่แล้ว +2

    many thanks. have the white tiny but with the board of tiny s. worked. thank you again . d16 Word. Transmitter is x9 light

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      Fantastic news!

  • @attktitan6057
    @attktitan6057 2 ปีที่แล้ว

    I can’t get my frsky taranis qx7 access to connect to the tiny hawks s. Also I saw the pinned comment that said to do bind_rx instead of bind_rx_spy, but only bind_rx_spi worked for me as of 6/23/22. Does anyone know what to do?

  • @CarbonGlassMan
    @CarbonGlassMan 4 ปีที่แล้ว

    This is giving me an error message saying Unknown Command try HELP when doing this to my Tinyhawk 2. It worked on my Freestyle 2. Any idea why?

  • @SANDY-FPV
    @SANDY-FPV 5 ปีที่แล้ว +2

    Hy Ian, I live in the Netherlands (EU) So I got my drone reviver in X_LBT or something, dont know if thats ok? But it workt! I got my drone bind to my X-lite pro. But here is the problem, if I go to the tab
    in betaflight transmitter or something, I can see the chanels moving the right way. But the signal dropt out sometime's.... And I don't know how to set up the drone so it can fly... But I have looked on the internet and saw that it is a really big bug or something. Do you know the problem? So yes, do you have a way to fix it?
    Let me know, thx

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      If LBT firmware works, use it. I have never used it, but I live in the U.S. and I think you are supposed to use LBT in Europe if I understand correctly.
      Unfortunately I have also heard that the Tinyhawk sometimes has range issues in D16 mode, but you must use D16 with the X-Lite Pro unless you get a multiprotocol module for your X-Lite that has FrSky D8 mode. One easy way I have found to get more range is to change the location of the antennas, so they are higher and further away from other parts of the Tinyhawk. I just made a video for you about how to do this:
      th-cam.com/video/ONSjU0eaBik/w-d-xo.html
      Good luck!

    • @SANDY-FPV
      @SANDY-FPV 5 ปีที่แล้ว

      @@IanBeaty Thx for the tip, I will look futher for a solution

  • @soerenmalik
    @soerenmalik 4 ปีที่แล้ว

    When i type in bind_rx_spi my betaflight says "error unknown command"?? What do I do??

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Are you doing it on a stock Tinyhawk S or Tinyhawk Freestyle flight controller board? Are you using the original stock version of Betaflight that came with the Tinyhawk S or Tinyhawk Freestyle? If you are using a different flight controller, or if you flashed a new version of Betaflight, this setting may have changed or may not work. If you are still using the original version of Betaflight, make sure you type exactly "bind_rx_spi" and then hit the Enter key. If you are using an older version of Betaflight try the "frsky_bind" command and I also just read a that you could try “bind_rx” because some versions of Betaflight might use that. Also double check in the "Configuration" tab in the "Receiver" section that you have "SPI RX support" and "FRSKY_D" selected. Good luck!

    • @alexgeller9105
      @alexgeller9105 4 ปีที่แล้ว

      Depends on betaflight version command is different: brushlesswhoop.com/spi-bind-via-betaflight/

    • @MrElScorpio
      @MrElScorpio 4 ปีที่แล้ว

      try just bind_rx

  • @IanBeaty
    @IanBeaty  5 ปีที่แล้ว

    I have heard that on the Tinyhawk that D8 works better than D16. I heard people say you get more range with D8, but that only applies to the Tinyhawk specifically. Normally D16 is better. The only reason I would use D16 mode on a Tinyhawk is if it is not possible for your transmitter to bind in D8 mode. On other quads I would use D16 instead of D8.

  • @MachuFrey
    @MachuFrey 4 ปีที่แล้ว +1

    I had this working then update the Tinyhawk freestyle to 4.1 and now this doesn't seam to work. whenever I try to bind, nothing happens.

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +1

      You might want to double check that you put the correct target of Betaflight on your flight controller. You might have put a version that does not support the SPI receiver. I have heard of people contacting Emax to help them reinstall the original version and its settings. You can always go back to the version that was working.

    • @AndrewJLintz
      @AndrewJLintz 4 ปีที่แล้ว

      have you been able to get your Tinyhawk to bind with d16 with the 4.1? I got a xd9+se2019 and the tinyhawk 2 freestyle isn't binding :(

  • @joshuabichsel
    @joshuabichsel 3 ปีที่แล้ว

    Has anyone gotten this bound to a FrSky Taranis X9D Plus SE. I cant get this to work at all...

  • @thadollagenerale
    @thadollagenerale 3 ปีที่แล้ว

    Excellent video, got me bound to my tinyhawk II. thanks

  • @pug6871
    @pug6871 5 ปีที่แล้ว

    Is d16 better than d8?

  • @alessandrocalabro9807
    @alessandrocalabro9807 3 ปีที่แล้ว

    man I can't get it bound... I have a taranis qx7 Acces and a tinyhawk1 original. I do all the steps but i get a "0" on rx num, what do i do? gosh im desperate

    • @IanBeaty
      @IanBeaty  3 ปีที่แล้ว

      Unfortunately the newer FrSky ACCESS protocol is not compatible with the older FrSky ACCST protocol. FrSky did this on purpose so that other companies could not use their newer technology. Because Emax made the receiver in the Tinyhawk it is ACCST. I think your best options are either to get a different transmitter that has ACCST built in such as an older FrSky, or even better get a Jumper or Radiomaster transmitter than has a built-in multiprotocol module that can bind to almost anything, or you can also get a separate multiprotocol module that plugs into the back of your QX7. The cheapest option is to solder a new ultra light FrSky ACCESS receiver into the Tinyhawk, but that adds some weight reducing your flight time and control.

    • @alessandrocalabro9807
      @alessandrocalabro9807 3 ปีที่แล้ว

      @@IanBeaty Well Exactly I have a Taranis qx7, the box says the following:
      Model: X7 ACCESS
      RF Mode: ACCESS & ACCST D16
      Firmware: LBT
      Could it work if I buy an external multiprotocol module to plug in the qx7? How do I know which one will work for me? I'm very new to this, any tips would help a lot! thanks!

  • @gorally2003
    @gorally2003 4 ปีที่แล้ว

    Thanks you really helped me i was struggling and Noone else said to check the bind or save it

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      So glad to help!

  • @paulb9015
    @paulb9015 4 ปีที่แล้ว +1

    Hi Ian I need some help with trying to bind my tinyhawk 2. I have a Frsky Xlite s lbt and I have spent ages trying to bind them together using an xjt lite module set on D8 but I never manage to bind successfully. So today I have done what you did on Beta flight and when I check to see if the bind has worked I get this message. warning no custom defaults found betaflight. Have you any idea what I have done wrong.

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Hey Paul. I do not yet have a Tinyhawk 2 so I am not sure if they have changed anything on its flight controller. I also live in the U.S. and have not worked with lbt firmware, nor have I used an XJT module. With all of that said, I have a couple ideas.
      First, do you have a version of OpenTX on your Xlite that has the multiprotocol module enabled? You may need to flash a new version of the firmware to be able to do that. If that part works, does you Tinyhawk Receiver have lbt firmware on it? I don't know how the built-in receiver works with EU or non-EU firmware variants, but that could possibly be the issue. Maybe there is a way to flash EU firmware, but if not you can also solder on an external receiver with lbt firmware, a small one like the XM which would really improve your range. There are even smaller ones too. Also, you might find helpful information in this thread: support.betafpv.com/support/solutions/articles/27000051569-how-to-bind-to-spi-frsky-receiver-a-guide-for-eu-lbt-radio-controller-users Good luck!

    • @paulb9015
      @paulb9015 4 ปีที่แล้ว

      @@IanBeaty Hi Thanks for getting back to me. I will have a look tomorrow when I have some time and try those things out. I am new at this hobby so at the moment Im still learning all this. Its just bad luck that my first attempt at this I end up buying a xlite that does not talk to tinyhawk lol. But I think its maybe a problem with the xlite I must have messed something up when I was updating the radio. Maybe I should have bought a Jumper T16 pro than I would not have the problem with D8.

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      @@paulb9015 I have another friend who is new to the hobby and bought the X-Lite Pro to go with his new Tinyhawk Freestyle and could not figure it out. That is why I made this video. A T16 would make some of this easier, but you might still be able to get this working by updating firmware again.

    • @paulb9015
      @paulb9015 4 ปีที่แล้ว

      @@IanBeaty Still not having much luck with binding anything to my x lite. Today I bought a XSR- usb Sim which is EU LBT and guess what that wont bind either lol. What I know now is it must be my x lite were the problem lies since it wont bind to my hawk or the new xsr sim I just got. I have done another factory reset on it and again flashed the latest firmware to it version 2.3.5 and I have done the bootloader too plus sd card. I think it must be the internal xjt module but saying that my external xjt lite module wont bind either but it lights up at the back.
      I never thought I would have such a hard time trying to get this to bind. I wont give up but its getting me down now because its just a nightmare sometimes feel like getting rid of the lot and just fly my Mavic but I really want to try this hobby but this Frsky X lite is a big mistake.
      I dont know what to do now so I will have to give it some more thought how to get this thing to bind.

    • @paulb9015
      @paulb9015 4 ปีที่แล้ว +1

      Hi Ian I am happy now after spending many hours trying to sort my radio out I have finally managed to bind to the usb sim. I should hopefully be ok binding to the hawk now so I will try that tomorrow and see how it goes but the main thing is im getting there now. Thanks again

  • @cometpowell
    @cometpowell 4 ปีที่แล้ว

    Cant bind to my taranis X7 Access.
    Followed all the steps

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Sorry about that. FrSky ACCESS protocol is a different newer protocol that is not compatible with the older FrSky ACCST protocol that comes on Emax Tinyhawks and many other drones and receivers. FrSky created ACCESS on purpose this way so that companies such as Emax would be locked out of their new ACCESS protocol ecosystem. It is very unfortunate and frustrating that they stabbed their customers and the industry in the back in that way. You can still use the Tinyhawk with a different transmitter that has a multiprotocol module or you could get a receiver that has ACCESS and solder it onto the Tinyhawk flight controller.

    • @cometpowell
      @cometpowell 4 ปีที่แล้ว

      Got it to bind but can’t fly it. Bad RSSI and RX loss. It sucks cause get fpv told me it would work. Reaching out to them I guess

  • @CarbonGlassMan
    @CarbonGlassMan 4 ปีที่แล้ว

    Thanks! This worked for my Freestyle 2, but I have a question. Is the range the same as it would be in D8 mode? Are there any limitations because you're in D16 instead of D8 mode? If so, it might be a good idea for me to get a D8 module for my X9 Lite. My goggles say low RSSI a lot, even when I'm not very far away.

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +1

      Yes, I have noticed and heard from other people that D16 mode on these sometimes has worse range. D8 should give you better range so I would use D8 if possible. You can do some minor antenna adjustments on the Tinyhawk to help with the range, but that may or may not help a lot with the range. It is worth a try and does not cost anything and would also help give you more range in D8 mode. I have a short video about repositioning the antennas for more range if you want to try it.

  • @realnoname_
    @realnoname_ 3 ปีที่แล้ว

    been trying for over an hour now, im getting really, really annoyed! I have a taranis x9 lite.. i've tried every single option now except for flashing the firmware on the drone or updating my firmware on my controller.. Could that be the problem here?

    • @realnoname_
      @realnoname_ 3 ปีที่แล้ว

      UPDATE: Nevermind!! I set the reciever to FRSKY_X_LBT mode, worked first try! Thank you so so so so much dude!

  • @TheLoganatorz
    @TheLoganatorz 4 ปีที่แล้ว +2

    Thanks for the tutorial!
    Only thing I noticed is that the power occasionally quits on the drone (I don’t loose video feed though). I’m using the X9 lite and the tiny hawk freestyle if anyone could help that would be much appreciated :)
    Again thanks a million for the tutorial XD

  • @RiMavicAir
    @RiMavicAir 4 ปีที่แล้ว

    Hello,
    I hope you can help me .... I'm Italian and I can't understand the steps to pair freestyle with frsky lite pro.
    I can't see the video of the radio settings well.
    Can you write them so I try to follow them? thanks, Mauro.

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +1

      Hello Mauro. I just wrote out all of the instructions for you in the top pinned comment. I hope this helps!

    • @RiMavicAir
      @RiMavicAir 4 ปีที่แล้ว

      @@IanBeaty ..thanks!!!👍

  • @davenow1017
    @davenow1017 4 ปีที่แล้ว

    My problem is to connect betaflight with the tinyhawk s .... it says: failed to open serial port. What can I do? I use betaflight 10.6.0 thx for supporting!

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +1

      There are quite a few reasons that might be happening, but it is not specific to the Tinyhawk. That applies to connecting Betaflight to anything. Here is what I would try, in this order:
      1) Try using different COM ports in Betaflight when you try to connect
      2) Try the ImpulseRC Driver Fixer (a google search will find it)
      3) Try different USB ports
      4) Try different USB cables
      I am sure there are more in depth things to try, but one of these things typically works for me. If all else fails, you can use the SpeedyBee Betaflight app on a phone or tablet with a USB OTG adapter. Good luck!

    • @davenow1017
      @davenow1017 4 ปีที่แล้ว +1

      Ian Beaty it was a wrong cable but now only.... and the bindig didn’t work your way. My Tinyhawk has to be powered before binding. I flashed an update to my taranis without a EU version to get D8 too. Finally I changed things in betaflight and now everything is working. Thx

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว +1

      @@davenow1017 Glad to hear everything is working!

  • @paulwrobel2994
    @paulwrobel2994 4 ปีที่แล้ว

    I have a original white tiny hawk and the same radio you got on your video but I can't bind them, why?

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      The original Tiny Hawk only works in D8 mode. It does not have D16 mode capability. Just bind it the normal way in D8 mode. In this video description I have a link for how to bind a Tinyhawk S in D8 mode and that is pretty much how you do it for the original white Tiny Hawk. Good luck!

    • @paulwrobel2994
      @paulwrobel2994 4 ปีที่แล้ว

      I have a original white hawk not the S but it cant bind even in d8 mode

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      @@paulwrobel2994 I fly my original white Tinyhawk the most. If it is not binding in D8 mode, something else must be wrong.

  • @michael3573
    @michael3573 5 ปีที่แล้ว +1

    Awesome. Thank you. Great clear directions.

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      Thank you for the feedback!

  • @bm51879
    @bm51879 4 ปีที่แล้ว

    I’m getting a lot of dropouts in d 16 mode I tried to bind in d8 mode and it won’t bind I’m using jumper t8sg v2

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      D16 mode on a Tinyhawk is known to have range issues and the best way to help that I know of is to move the antenna to a better position. I think I made a video about that a while back. I do not know why the D8 mode would not be working though unless something is set up wrong in Betaflight. I have not used a Jumper radio before so I am not sure what could cause that issue from the transmitter end of the system.

  • @gooblenton1536
    @gooblenton1536 5 ปีที่แล้ว +1

    Thank you so much! Couldn't find anything to help me bind and was getting very frustrated.

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      Glad it helped! Have fun flying now!

  • @lobo5212
    @lobo5212 4 ปีที่แล้ว

    when i try to change somthing i doesnt change y reconect and changes dont stay

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      If you are talking about in Betaflight, make sure you save any settings before you switch to a new page of betaflight. To be safe, save each change immediately after making any change. You also needs to save any changes if you make changes from your OSD.

  • @emmjheyalagao7248
    @emmjheyalagao7248 4 ปีที่แล้ว

    Hi! Is this can work on the tinyhawk 2?

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      I do not know for sure, but I think it does.

  • @Mrcanonball19
    @Mrcanonball19 5 ปีที่แล้ว

    Hi if anyone could help me I'd really appreciate it!
    I have a FRSKY Taranis Lite and I've updated it for D16 support. I am trying to get it to bind to my Tinyhawk freestyle but it isn't working like shown in your video. When I check the rx number is always 00 regardless what number is on the transmitter.
    If anyone has any tips to get this working i'd be so grateful! Thanks

  • @gatot150
    @gatot150 5 ปีที่แล้ว

    Hello bro...i get problem TH cannot bind to my jumper T16 , what is mean no in frsky_rx_num ???
    Default is 0

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      I have not used a Jumper T16, but I would really like to. The frsky_x_rx_num is the model number in your radio that the Tinyhawk binds to. Change it to a number that is different from any other models in your radio and also change it to a number other than 0 so you know if it bound correctly when you look in Betaflight. Because you have a Jumper, you should be able to simply bind it in D8 mode like the Tinyhawk instructions explain how to do, unless you have the need to use D16 mode, but I have heard that the signal is better in D8 mode if your transmitter can do that. Have you tried D8 mode yet?

    • @gatot150
      @gatot150 5 ปีที่แล้ว

      Ian Beaty hi Ian...I have 3 drone , 1st bound is TH with old board BF 3.5.1 with D8 and numbe receiver 01
      2nd is eachine uk65 is bound with D8 too and number receiver 02
      3rd is cannot bound with T16 and already try D8 D16 number receiver 03 but the TH only bind mode in without bound.
      Any suggest to make my 3rd drone bound? Help me please

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      @@gatot150 Is the Tinyhawk that will not bind the new black Tinyhawk S? I don't quite understand what you mean by "but the TH only bind mode in without bound," could you explain more about what you mean by that?

    • @gatot150
      @gatot150 5 ปีที่แล้ว

      @@IanBeaty i am sorry about my english, I have 3 drones, 2 drone succed bound with my jumpert16 but only one cannot bound.
      i have tried D8 , D16 and flash firmware to the newest 4.10

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      @@gatot150 No problem. I just want to make sure I understand so that I can help better.
      I need to understand what you know or don't know. Do you know how to change between D8 and D16 mode in the Jumper? Do you know how to change between D8 and D16 mode in Betaflight on the drone?

  • @SeanOzz
    @SeanOzz 3 ปีที่แล้ว

    heck yes. buying a new remote that only does 16 so gonna try this for my s and freestyle. thanks

  • @oliveirafpv9123
    @oliveirafpv9123 5 ปีที่แล้ว

    Does this work for TinyHawk other than S?

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      Yes, this works for both the Tinyhawk S and Tinyhawk Freestyle. It does not work for the original Tinyhawk.

    • @guk771
      @guk771 5 ปีที่แล้ว

      No it does not work for a freestyle been on it hours now

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      ​@@guk771 Sorry to hear that you are having trouble with this. I know it works for Freestyle because it was on a Tinyhawk Freestyle that I first used this to bind to my friend's FrSky X-Lite Pro. I also tested it later on a Tinyhawk S. You might double check the spelling of the CLI commands, or make sure you typed "save" after doing the CLI commands. Good luck!

    • @guk771
      @guk771 4 ปีที่แล้ว +1

      @@IanBeaty nope never did work on my qx7 :( in the end upgraded software on qx7 so had d8 mode

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      @@guk771 That's too bad that it didn't work, but D8 mode tends to work better on a Tinyhawk than D16, so you are better off now. You should have a bit more range with D8. Just curious though, I did not know you could change the software on the transmitter to have D8 mode if D8 was not already on there. What upgrade did you do?

  • @MaRa-ly1gl
    @MaRa-ly1gl 5 ปีที่แล้ว +1

    Thank's, man! Now Tiny works great with new Taranix X9D SE 2019.

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      So glad it helped!

  • @AlexRodriguez-cb5om
    @AlexRodriguez-cb5om 4 ปีที่แล้ว

    I LOVE YOU! SUBBED!!!

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Thank you!

  • @johntaylor6243
    @johntaylor6243 4 ปีที่แล้ว

    Kick ass thanks!

  • @Justin002
    @Justin002 4 ปีที่แล้ว

    super helpful thanks

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Glad it helped!

  • @jntfpv3214
    @jntfpv3214 4 ปีที่แล้ว

    thank you!

    • @IanBeaty
      @IanBeaty  4 ปีที่แล้ว

      Definitely!

  • @operatedboy4
    @operatedboy4 5 ปีที่แล้ว

    Thanks a lot!!

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว

      Definitely!

  • @luckyfpv323
    @luckyfpv323 5 ปีที่แล้ว

    Nice

    • @IanBeaty
      @IanBeaty  5 ปีที่แล้ว +1

      Sweet videos with your cinewhoop! Keep it up. Your shots will only get better!

  • @wynnfpv
    @wynnfpv 5 ปีที่แล้ว

    👍🏼👍🏼

  • @niioniio
    @niioniio 3 ปีที่แล้ว

    For those, who this wont bind, try tu use FRSKY_X_LBT reciever option in the configuration

  • @MrSabram07
    @MrSabram07 4 ปีที่แล้ว

    Wow how did you all this complete confusion