Hey Andy, I just upgraded my eachine Novice1 to x2 solid ph2 connectors & it made a great difference! Also how's my crash video I uploaded, the novice1 can take a beating! Haven't even broken a prop yet😀.
Hi Andy, in my opinion the voltage sag you keep mentioning does NOT ruin the batteries. The low capacity connector means a too high resistance between the battery and the electronics of the drone. The voltage sags on the electronics side but not at the battery. The result is that the battery stays intact but you lose power on the drone and also the connector can become hot. So while this is not good, you can stop worrying about the battery...
there is no opinion in this matter only facts. The connector creates a bottle neck / resistance. this causes the lipo to drop below 3.3volts on a punch out due to said resistance pretty much as soon as you arm. ergo polymer starts to break down and destroys it. you need to worry about this or should I say your wallet does
on 1s i like the walkera connectors i think they call them micro losie or somethink i use them on 7mm whoop with stock whoop fc and 300mah lipo with that connector more power longer flight times no more whobbel of death
Thanks so much for your in depth thoughtful review of the Tinyhawk 2. I learned a lot! I really enjoyed your flight inside your house - I did not think you would make it going under the chairs ... such smooth flight, very inspiring.
That for the review. I was going to buy it for the new mounted camera but now I'm not sure. I have the S version but every crash there is the risk to unmount the camera : it is an annoying problem...
I raised angel limit to 70... I need to check my sky03o if it has some problem but on emax googles the top part of screen was cut out on emax googles.. so i couldnt raise the numbers,..
Hi Andy. Thanks for great videos. You keep saying that voltage sag, caused by thin wires damages the battery, but i thought that voltage is dropped between the battery terminals and connector/board but not on the battery itself, so thin wires will only limit the maximum current but will not harm the battery... Am i wrong?
Andy, love your stuff. Do Not bind the Tinyhawk 2 in D16. It constantly failsafes and drops to the ground while the RSSI value shows high. In D8 it works fine.
My tinyhawk s only got 3:00 to 3:20, no matter the battery. Do you have a PID dump for the TH2? My TH2 comes tomorrow (2 of them actually, want my buds to fly with me!). The AIO is the same for THS, TH2, and THfreestyle, aside the 200mw vtx in the TH2, so I am hoping for similar results. Also looking hard at the THfreestyle... I really enjoyed my THS until I broke the board...
Merry Christmas Andy! I just got my tinyhawk 2 and have logged quite a few hours of outdoor flying. I have a rather small yard and it performs very well in that environment. I haven't seen any Jell-O on 1S or 2S. On my new batteries I was getting as much as 4 minutes of flight time. The 2s is a nice option but I think it needs a little bit of work on the tune and a change in the connector. It has very few shortcomings and they are definitely out shadowed by how much fun it is to fly! Cheers.
Been happy with my Tiny Hawk S for a while now, disappointed Emax couldn’t really better it considering they have been on a good run recently. Merry Christmas everyone
Hey Andy RC, question about the TH II, have you ever had it apart? reason I ask is it appears the connector you plug the motor into is glued to the board ( perhaps not soldered) as I was unplugging the motors they all were easily removed until the 4th one, the minute I went to unplug it the entire connector/plug came off the board...it has 3 contacts in front and one on each corner of the rear, BUT looks like it just lays on the board and is glued on...glue looks clear and shiny, I see no way to solder it, and I know of no soldering iron that small to be able to get under the connector to solder the contacts....any advice or help would be appreciated if you have any...Thanks in advance.
Mine arrived today, a week late but never mind,, Bit of a difference to my little inductrix that's for sure lol I use almost 3 quarter of throttle for hover is that normal
Nice review! Thanks. I have my Tinyhawk I on order and hope to be ripping (a little) around the house during the cold months. Thank u for all u do for the community. Merry X-mas and happy new year
Buen vídeo he aprendido mucho. Pero mi pregunta es la siguiente....Se puede enlazar con la emisora del Tinyhawk I (Emax E6 Transmisor). Gracias....... Saludos.
Andy . If the vtx antenna on the tinyhawk with the bad video is not sticking out . Take it apart and get it sticking out and try that . Thanks for the great video's
Nice review as always Andy, I like your sensible approach. Have yourself a very Merry Christmas with your family and friends. Everyone also have a Merry Christmas. Jeff (loved the home tour!, nice.)
I'm thinking about putting the Tinyhawk 2 board into my Tinyhawk Freestyle, for the VTX upgrade. Other than a bit of soldering, I'm guessing it would be just a matter of changing the FC orientation and changing the PID tune and other values to Freestyle specs. Can anyone give advice on that?
Thank you for all your reviews you have made for us all and hope santa brings you something nice. Its funny how manufactures miss the details in the rush to get something released when its the details that will sell the product as being fully worked through.
excellent informative review. I'm using this platform to learn fpv. I prefer to fly outdoors on a calm day but the original TH suffered range anxiety so I just order the 2 and glad to hear your statement on additional range. How do you increase the vtx power to 200? Is that done through bf?
The tinyhawk s is perfectly fine of two s if you fly for only two minuets which is short but your batteries last a lot longer. Also could you do a review on the xilo phreakstyle???
Merry Christmas Andy. I wonder if the issue you had with the recordings in the sports hall and the motor way services was due to the type of lighting they were using, depending whether they were fluorescent or LED and what frequency they operate on?
Can you help me out??.. I have jumper tx t8sg v3 plus .. but I can't get the motors to unlock and start.. I'm not sure why. I don't have beta Flight is that why I can't fly it?? .. thanks in advance
Hi Andy or anyone else who might be able to comment..... I usually build and set up my own quads.....However I've decided I want an indoor smooth quad to fly around the house I did have a mobula7 over a year ago but even with throttle taming on betaflight I just couldn't get on with it and got rid of it. Watching a few youtube videos i'm now thinking of buying the new Emax tinyhawk 2 flying on 1s battery looks like a smooth indoor flyer (im not looking to race just to fly around the house under the tables chairs etc)...So here's my question ? My TX is a Taranis X9D+ Special Edition which is a EU version and my four outside quads all have EU software R-SXR receivers on them bound to D16. My Tx had either D16 or LR12 bind modes....Ive just put the latest Taranis update on my radio not ticking 'eu' on Open TX when I flashed it so now I have the option of either D16 or D8 binding. I've read online that through betaflight in the receiver option you can change the tinyhawk 2 from a 'Frsky D for 8 channel' to 'Frsky X for 16 channel' so the real question is this.....Can I now bind in D8 Mode or D16 Mode and what would be the difference am I still getting full telemetry in both ? I only have one model set up in my Tx so all my quads are bound to that ie D16 mode so if I bound to D8 my other models wouldn't work unless I created a second model to bind in D8 ? Basically if I bound in D16 like all the other four quads I could then run the tinyhawk on the one model set up but would I still get telemetry ? I'm just trying to work out the difference between D8 and D16 ? The Emax tinyhawk states its a spi receiver compatible with Frsky D8 mode ? Thanks for any advice .
Thanks for the great info Andy, I have 5 tinyhawks (for the kids) and I fly a TH2s for myself. Next burnt esc and I'm upgrading to either TinyHawk ll or ??? What would be a better alternative if any ?
Has anyone verified a voltage drop across the connector with a voltmeter? It seems more that it would be the current demand is simply too high for the battery.
I'd get the s model. I'm wondering if we should be using 4k4k at 300dshot if we will use rpm filter? Nice guitars I have 5 of my own. My favorite one I have is my les Paul studio ebony color left hand.
Is this thing worth it as a starter drone? I have a Mavic Air but I want to get a bit in FPV flying... I have literally no experience with fpv, only on my Mavic Air which is mostly flying itself :D So what drone can you recommend?
Suggestion from me and my experience is getting a nice radio and getting into some simulators like Velocidrone (racing based but you can freefly) and liftoff on steam. This will give you some fundamentals you would otherwise learn crashing an FPV drone over and over. I then bought a Tinyhawk and cheap box goggles from banggood.com and have been flying it in horizon mode in the house. I've now just switched to acro indoors and I'm flying relatively smoothly. I'm confident enough to now build my own 5" and start ripping. The tinyhawk line is probably the best starter FPV drone you can get in my opinion.
Dear Andy, can I move my original tiny hawk to V2 frame ?! from what I can see on this video, its possible except of the camera of course , the thing is I damaged my camera on Tiny hawk and already have a caddex camera ( from my old trashcan) , and although there is a way to install it in original frame but I got the feeling it would be perfect in V2 frame, am I right ?! thanks a lot, by the way always great videos , learning a lot from you man, Thank You
Hi Andy, greetings from Greece. Could you please give me the exact description (type/name) of the motor jst 3pin plug? A drop of solder fell on one of the plugs and melted it. The motor is fine but cannot find how to order the plug to replace. Your reply is much appreciated.
Hello friends, I'm desperate. I have a Tinyhawk 2. The drone connected to "Betaflight". Entered the commands "set usb_hid_cdc = ON" via "Betaflight Configurator" and then "save". That worked too. Later I wanted to set the setting to "OFF". Now I get no connection to Tinyhawk. Can someone help me here?
You should not disconnect when the hid setting is set "ON". Always set it back to off before disconnecting the tinyhawk. There is some way to restore it as i heard of other people with this problem, have you fixed it?
Thank you for the video but I can’t seem to figure out what I’m doing wrong, I got it to bind with my frsky x lite but can’t seem to arm it. Blue led stays on solid on the quad but when I hit throttle a red led comes on but no power to the props. Any suggestions? I also can’t get it to connect to betaflight :/
Hi there just wondering if you can help I have a tint hawk 2 rtf kit as I'm a fpv noob and mid flight I lost rssi now when I turn my drone on I have 2 flashing leads red and blue and I can enter bind mode but cant bind the emax controller any help would be much appreciated thank
just got my th2 . Binded quickly . Flies like my original th in rtf configuration the angle limit was set onto 60 on mine though for some reason BTW is smart audio enabled already on it? I think I'm able to change racebands on mine already . Not sure where to put the turtle mode though . Set to aux 4 and the arming angle limit was limitless
Hey Andy, thanks for the review. What are your day driver's these days? O30's, HDO or 2? I just build a Tadpole with a Iflight V1.5 stack, Fywoo 1103 7650kv, Runcan nano 2, running Tattu 2S 450's outstanding micro! Thanks again and merry Christmas bro!
@@AndyRCchannel Just got my HDO2's in 3 days ago, great goggles but I had to use the Sky O30's cushion as my eyelashes we're hitting the lenses, I did get the newbeedrone foam on them today, which is what Im using on the Sky O30's, which is even thicker and now they are outstanding! Only complaint is, I wish they would have went with the better DVR. When you do get them don't give up on them if they don't fit right as first, just find the right thickness of cushion for you, the OG cushion is super thin. Now, I'm just waiting on that Skyzone module bay so I can rock the TBS Fusion on the Sky O30's and the Rapidfire on the HDO 2's. Orqa's where to expensive, after the goggles and a module, you might as well get the DJI system.
@@TexasWaters Iv already tried painless 360s so i know i like them and they fit well. iv just had to order from china to save money and they are all still out of stock :(
AndyRC you will Andy you will. No worries. Your famous now Shirley you will acquire what we all would love to see reviewed and who other then the master class uk pilot himself Andy rc. Cheers
Less flight time... Pass. I changed my OG Tinyhawk with the S motors and it now flies at around 4 minutes, but the TH S is still the best I get a flight time of 5 minutes and can take 2s.
I always charge HV to a HV voltage.. now i watched your vid and hear you say, that you never charge them to a HV voltage? So will it perfom like a normal 3.7v lipo if i charge them like that? I quess now im also charge them like a normal lipo.
I miss the words, it looks more like the very first prototype of a tinyhawk. Backsliding instead of progress in almost every way. Ok where should i start 1. much too expensive 2. much too heavy 3.Electrically, everything at or above the limit (motor connector only approved up to 3A) The Mobula 6 (Runcam Nano 3) incl. 4x1S lipos costs just € 67 (with code) and weighs under 20g.
I'm having a lot of interference with my video while flying inside. I'm not having that problem outside. I'm not having that problem with my other quads inside. Anyone have any suggestions to help with the video?
Tinyhawk II: bit.ly/34Ru3zx Coupon: BGTHAWKII
Tinyhawk S: bit.ly/2wBub7z
Tinyhawk I:bit.ly/2uuQAlR
Freestyle:bit.ly/2Kz94t1
All BG Coupons: bit.ly/2O6f5Pt
1s lipo: bit.ly/2TXW0oF
2s lipo: bit.ly/34St1Dl
Test Clamp: amzn.to/2PQoP2q
Hey Andy, I just upgraded my eachine Novice1 to x2 solid ph2 connectors & it made a great difference! Also how's my crash video I uploaded, the novice1 can take a beating! Haven't even broken a prop yet😀.
Can you cli dump default settings please?
I've always found putting some solder in the pins to make them solid really help performance and eliminates alot of sag on 1S..
this is quite a nice upgrade.. love that they made the frame white again.. the black one was too hard to find in tall grass...and the leds are a plus.
Hi Andy, in my opinion the voltage sag you keep mentioning does NOT ruin the batteries. The low capacity connector means a too high resistance between the battery and the electronics of the drone. The voltage sags on the electronics side but not at the battery. The result is that the battery stays intact but you lose power on the drone and also the connector can become hot. So while this is not good, you can stop worrying about the battery...
there is no opinion in this matter only facts. The connector creates a bottle neck / resistance. this causes the lipo to drop below 3.3volts on a punch out due to said resistance pretty much as soon as you arm. ergo polymer starts to break down and destroys it. you need to worry about this or should I say your wallet does
on 1s i like the walkera connectors i think they call them micro losie or somethink i use them on 7mm whoop with stock whoop fc and 300mah lipo with that connector more power longer flight times no more whobbel of death
19:10 not because of people ask for it, but because they share the same board for freestyle which uses 2s only. Less different boards - less work.
Thanks so much for your in depth thoughtful review of the Tinyhawk 2. I learned a lot! I really enjoyed your flight inside your house - I did not think you would make it going under the chairs ... such smooth flight, very inspiring.
Tinyhawk v1 kit has got at least 4 people I know of into FPV. Such a great package. Hope emax keep it up with the RTF kits.
That for the review. I was going to buy it for the new mounted camera but now I'm not sure. I have the S version but every crash there is the risk to unmount the camera : it is an annoying problem...
Change the connector to a xt30 and flash the ESCs to Jesc 48khz and you will get about 30-40 more seconds of fun.
Thank you for this! I'm looking to get the RTF kit and this helps me plan to begin and then expand as my and my son's skill improves.
Fantastic flying and review, Andy!!! 😃
Merry Christmas, dude! For you and your family! 😊
merry xmas MC's Creations :)
@@AndyRCchannel taking the CHRIST out of christmas aint cool. You know its somebodys birthday, right?!? Dont make me unsub...
I raised angel limit to 70... I need to check my sky03o if it has some problem but on emax googles the top part of screen was cut out on emax googles.. so i couldnt raise the numbers,..
Hi Andy. Thanks for great videos. You keep saying that voltage sag, caused by thin wires damages the battery, but i thought that voltage is dropped between the battery terminals and connector/board but not on the battery itself, so thin wires will only limit the maximum current but will not harm the battery... Am i wrong?
Andy, love your stuff. Do Not bind the Tinyhawk 2 in D16. It constantly failsafes and drops to the ground while the RSSI value shows high. In D8 it works fine.
My tinyhawk s only got 3:00 to 3:20, no matter the battery. Do you have a PID dump for the TH2?
My TH2 comes tomorrow (2 of them actually, want my buds to fly with me!). The AIO is the same for THS, TH2, and THfreestyle, aside the 200mw vtx in the TH2, so I am hoping for similar results. Also looking hard at the THfreestyle... I really enjoyed my THS until I broke the board...
PS thanks for the channel, since I got into FPV, I watch a LOT of them, lol
Merry Christmas Andy! I just got my tinyhawk 2 and have logged quite a few hours of outdoor flying. I have a rather small yard and it performs very well in that environment. I haven't seen any Jell-O on 1S or 2S. On my new batteries I was getting as much as 4 minutes of flight time. The 2s is a nice option but I think it needs a little bit of work on the tune and a change in the connector. It has very few shortcomings and they are definitely out shadowed by how much fun it is to fly! Cheers.
you wont get jello flying in a garden you have to give it full throttle
Been happy with my Tiny Hawk S for a while now, disappointed Emax couldn’t really better it considering they have been on a good run recently. Merry Christmas everyone
Hey Andy RC, question about the TH II, have you ever had it apart? reason I ask is it appears the connector you plug the motor into is glued to the board ( perhaps not soldered) as I was unplugging the motors they all were easily removed until the 4th one, the minute I went to unplug it the entire connector/plug came off the board...it has 3 contacts in front and one on each corner of the rear, BUT looks like it just lays on the board and is glued on...glue looks clear and shiny, I see no way to solder it, and I know of no soldering iron that small to be able to get under the connector to solder the contacts....any advice or help would be appreciated if you have any...Thanks in advance.
I’m hooked watching your videos as I keep waiting for you to say um or uh. Not one so far. Amazing.
Not written in the script 😃
Hi again Andy, I’m talking of course about the tinyhawk 1. Cheers.
I like the fender Tele. Have the Strat and It is my favorite of all my guitars. Thanks for the vid.
Mine arrived today, a week late but never mind,, Bit of a difference to my little inductrix that's for sure lol
I use almost 3 quarter of throttle for hover is that normal
Nice review! Thanks. I have my Tinyhawk I on order and hope to be ripping (a little) around the house during the cold months. Thank u for all u do for the community. Merry X-mas and happy new year
Buen vídeo he aprendido mucho. Pero mi pregunta es la siguiente....Se puede enlazar con la emisora del Tinyhawk I
(Emax E6 Transmisor). Gracias....... Saludos.
Excellent review & flights Andy!! Merry Christmas to you & your family 🎄🎅
i would just change lipo connector i do the same with a whoop makes a big difference
Andy . If the vtx antenna on the tinyhawk with the bad video is not sticking out . Take it apart and get it sticking out and try that . Thanks for the great video's
The tinyhawk I fly has both antennas sticking out. That one is a spare I bought
Merry Christmas, Andy. Thanks for everything you do.
Thanks Andy, Well explained. Love your honest and educational reviews and videos.
Keep up your great work. 🙏👌
Nice review as always Andy, I like your sensible approach. Have yourself a very Merry Christmas with your family and friends. Everyone also have a Merry Christmas. Jeff (loved the home tour!, nice.)
it would be nice to switch all the tinyhawk 2 components on to the freestyle frame for a try
Merry Christmas Andy !! Hope you get some family / friends time !!
I changed my connection to JST XH for all my 1s it makes quite a different.
I'm thinking about putting the Tinyhawk 2 board into my Tinyhawk Freestyle, for the VTX upgrade. Other than a bit of soldering, I'm guessing it would be just a matter of changing the FC orientation and changing the PID tune and other values to Freestyle specs. Can anyone give advice on that?
Thank you for all your reviews you have made for us all and hope santa brings you something nice. Its funny how manufactures miss the details in the rush to get something released when its the details that will sell the product as being fully worked through.
thanks. Wynne hope you have a good one and see u soon!
Happy new year Andy and your family.Really lovin the channel my friend.
Great review Andy.. of the three Tiny Hawks and the Tiny Hawk racer which is your favorite?
excellent informative review. I'm using this platform to learn fpv. I prefer to fly outdoors on a calm day but the original TH suffered range anxiety so I just order the 2 and glad to hear your statement on additional range. How do you increase the vtx power to 200? Is that done through bf?
The tinyhawk s is perfectly fine of two s if you fly for only two minuets which is short but your batteries last a lot longer. Also could you do a review on the xilo phreakstyle???
Merry Christmas Andy. I wonder if the issue you had with the recordings in the sports hall and the motor way services was due to the type of lighting they were using, depending whether they were fluorescent or LED and what frequency they operate on?
Dam 2s thru that 1 pH connector has crazy sag hey! Sweet review as always Andy👍
I just ordered one and subscribed. Good informative video.
Can you help me out??.. I have jumper tx t8sg v3 plus .. but I can't get the motors to unlock and start.. I'm not sure why. I don't have beta Flight is that why I can't fly it?? .. thanks in advance
im sold my th s and bought a th 2.. sadly i think that th s is much better if you change the cam to nano 3
Finally! I have been waiting for this review. Merry Christmas Andy 🎄🎅🎁
your welcome merry xmas
Awesome. Love the TINYHAWK's, got the first and S! This is definitely one to add to my fleet. Merry Christmas and a Happy New Year. Cheers buddy 👍✈️😊
Thank you Andy and Merry Christmas.
Great review Andy! Enjoyed that.
Hi Andy or anyone else who might be able to comment..... I usually build and set up my own quads.....However I've decided I want an indoor smooth quad to fly around the house I did have a mobula7 over a year ago but even with throttle taming on betaflight I just couldn't get on with it and got rid of it.
Watching a few youtube videos i'm now thinking of buying the new Emax tinyhawk 2 flying on 1s battery looks like a smooth indoor flyer (im not looking to race just to fly around the house under the tables chairs etc)...So here's my question ?
My TX is a Taranis X9D+ Special Edition which is a EU version and my four outside quads all have EU software R-SXR receivers on them bound to D16.
My Tx had either D16 or LR12 bind modes....Ive just put the latest Taranis update on my radio not ticking 'eu' on Open TX when I flashed it so now I have the option of either D16 or D8 binding.
I've read online that through betaflight in the receiver option you can change the tinyhawk 2 from a 'Frsky D for 8 channel' to 'Frsky X for 16 channel' so the real question is this.....Can I now bind in D8 Mode or D16 Mode and what would be the difference am I still getting full telemetry in both ?
I only have one model set up in my Tx so all my quads are bound to that ie D16 mode so if I bound to D8 my other models wouldn't work unless I created a second model to bind in D8 ?
Basically if I bound in D16 like all the other four quads I could then run the tinyhawk on the one model set up but would I still get telemetry ? I'm just trying to work out the difference between D8 and D16 ?
The Emax tinyhawk states its a spi receiver compatible with Frsky D8 mode ?
Thanks for any advice .
Merry Christmas and Happy New Year to all !🎁🎄🎅⛄🎉
Thanks for the great info Andy, I have 5 tinyhawks (for the kids) and I fly a TH2s for myself. Next burnt esc and I'm upgrading to either TinyHawk ll or ???
What would be a better alternative if any ?
Eachine Trashcan is better and cheaper also the parts are cheaper
HII , thank you for share.
WICH is better (I want to be strong, and use mostly outside, and be cheaper owerall) This tinihawk or ldark or et125 4s.??
What voltage should I stop flying at? I have the Freestyle 2 which is the same board. I fly both 1s and 2s on it.
Has anyone verified a voltage drop across the connector with a voltmeter? It seems more that it would be the current demand is simply too high for the battery.
I'd get the s model. I'm wondering if we should be using 4k4k at 300dshot if we will use rpm filter? Nice guitars I have 5 of my own. My favorite one I have is my les Paul studio ebony color left hand.
its not using rpm filter.
AndyRC I was just saying IF we were to use rpm filter.
Start with 2k 2k with dshot 300 and see what the cpu load is
Can an ND filter be added to the camera lens to reduce/eliminate jello?
Is this thing worth it as a starter drone? I have a Mavic Air but I want to get a bit in FPV flying...
I have literally no experience with fpv, only on my Mavic Air which is mostly flying itself :D
So what drone can you recommend?
Suggestion from me and my experience is getting a nice radio and getting into some simulators like Velocidrone (racing based but you can freefly) and liftoff on steam. This will give you some fundamentals you would otherwise learn crashing an FPV drone over and over. I then bought a Tinyhawk and cheap box goggles from banggood.com and have been flying it in horizon mode in the house. I've now just switched to acro indoors and I'm flying relatively smoothly. I'm confident enough to now build my own 5" and start ripping. The tinyhawk line is probably the best starter FPV drone you can get in my opinion.
RavenDE the tinyhawk classic rtf package of course
Dear Andy, can I move my original tiny hawk to V2 frame ?!
from what I can see on this video, its possible except of the camera of course ,
the thing is I damaged my camera on Tiny hawk and already have a caddex camera ( from my old trashcan) , and although there is a way to install it in original frame but I got the feeling it would be perfect in V2 frame,
am I right ?!
thanks a lot,
by the way always great videos , learning a lot from you man, Thank You
Hi Andy. Any chance you know how to turn off the god damn LEDs! They are on all the time and I want them off!
Merry Christmas andy :)
Is a very cool looking whoop!!!!!.
Great Review & Great Flying!!!!.
👍😀👍
Hope you have a great Christmas!!
Hi Andy, greetings from Greece. Could you please give me the exact description (type/name) of the motor jst 3pin plug? A drop of solder fell on one of the plugs and melted it. The motor is fine but cannot find how to order the plug to replace. Your reply is much appreciated.
I'm using the stock controller with my tinyhawk 2 would I have better control with a better radio
Hello friends, I'm desperate.
I have a Tinyhawk 2. The drone connected to "Betaflight". Entered the commands "set usb_hid_cdc = ON" via "Betaflight Configurator" and then "save". That worked too. Later I wanted to set the setting to "OFF". Now I get no connection to Tinyhawk. Can someone help me here?
You should not disconnect when the hid setting is set "ON". Always set it back to off before disconnecting the tinyhawk. There is some way to restore it as i heard of other people with this problem, have you fixed it?
Happy Holydys you too Andy!!
🎄🎄🎄🎄🎄🎄🎄🎄
🎆🎆🎆🎆🎆🎆
What VTX mv setting were you using in the house? 25, 100 or 200? And as always great review Andy.
where did you buy that landing pad
Thank you for the video but I can’t seem to figure out what I’m doing wrong, I got it to bind with my frsky x lite but can’t seem to arm it. Blue led stays on solid on the quad but when I hit throttle a red led comes on but no power to the props. Any suggestions? I also can’t get it to connect to betaflight :/
What are the steps to binding in D8 mode? Did you use a JR module d8?
Yaaaa 70k subs congrats
Happy Holidays to you and your family!. You're the best Quad Review channel!. I hope 2020 brings you newfound opportunities and good fortune!.
thanks for the support fpv club. Have a good one!
Merry Christmas and a prosperous new year , love from the uk ☃️☃️, soz if I left this comnent all ready.
TY for your comprehensive review 👌😊
Hi there just wondering if you can help I have a tint hawk 2 rtf kit as I'm a fpv noob and mid flight I lost rssi now when I turn my drone on I have 2 flashing leads red and blue and I can enter bind mode but cant bind the emax controller any help would be much appreciated thank
just got my th2 . Binded quickly . Flies like my original th in rtf configuration the angle limit was set onto 60 on mine though for some reason BTW is smart audio enabled already on it? I think I'm able to change racebands on mine already . Not sure where to put the turtle mode though . Set to aux 4 and the arming angle limit was limitless
There's a good chance that when I reccomend changes to be made they make them. You can change bands they are just limited
Hi andy was that fpv on 2s with a fresh battery or was it the same battery from the line of sight one
Thank you for the detailed review XDDD
I'm new to it and learnt much just from your review
It looks decent!. Merry Christmas!! Cheers
Hey Andy, thanks for the review.
What are your day driver's these days? O30's, HDO or 2?
I just build a Tadpole with a Iflight V1.5 stack, Fywoo 1103 7650kv, Runcan nano 2, running Tattu 2S 450's outstanding micro!
Thanks again and merry Christmas bro!
hdo with rapidfire. hoping to get the HDO2 but hard to get hold of!
@@AndyRCchannel Just got my HDO2's in 3 days ago, great goggles but I had to use the Sky O30's cushion as my eyelashes we're hitting the lenses, I did get the newbeedrone foam on them today, which is what Im using on the Sky O30's, which is even thicker and now they are outstanding! Only complaint is, I wish they would have went with the better DVR.
When you do get them don't give up on them if they don't fit right as first, just find the right thickness of cushion for you, the OG cushion is super thin.
Now, I'm just waiting on that Skyzone module bay so I can rock the TBS Fusion on the Sky O30's and the Rapidfire on the HDO 2's.
Orqa's where to expensive, after the goggles and a module, you might as well get the DJI system.
@@TexasWaters Iv already tried painless 360s so i know i like them and they fit well. iv just had to order from china to save money and they are all still out of stock :(
AndyRC you will Andy you will. No worries. Your famous now Shirley you will acquire what we all would love to see reviewed and who other then the master class uk pilot himself Andy rc. Cheers
@@AndyRCchannel Tried quadcopters.co.uk? I think they have them in stock now
Less flight time... Pass. I changed my OG Tinyhawk with the S motors and it now flies at around 4 minutes, but the TH S is still the best I get a flight time of 5 minutes and can take 2s.
I love emax quads. Thanks for the review.
Hey there Andy...pls could you tell me if this whoop beast can anyhow be binded with FlySky i6S tx?!
Do I have to buy and solder different rx?
Yes, you have to solder another receiver to the quad. th-cam.com/video/dQkkU0TxlFU/w-d-xo.html
Any idea if the camera is Pal or NTSC ??
Was that 4 minutes on 1s with the LEDs on? And can they be disabled? How much do you think they draw on the performance or flight time?
I see the LEDs are on after all
Does it still work? I heard they don’t last long
How do you connect up the Tinyhawk to your Pc ?
Is there a USB port on the FC ??
Have a great Christmas 👍😃
Yes it's behind the camera. Cheers
Congrats on 70k !
I always charge HV to a HV voltage.. now i watched your vid and hear you say, that you never charge them to a HV voltage? So will it perfom like a normal 3.7v lipo if i charge them like that? I quess now im also charge them like a normal lipo.
Yes it will perform the same as non hv but it will have a longer life
AndyRC for now i always charge them like a normal lipo then! Haha much thanksss Andy 🙏🏼
AndyRC btw if i want to storage them also in normal storage voltage? Or do i need the HV storage?
Tinyhawk ll Vs. Mobula 6? Please!! It would be an awesome video
Had one on the way and they cancelled my order
No comparison.....mob6:-)
What's the song at the end?
Merry Christmas, mate!
Merry Xmas :-)
I miss the words, it looks more like the very first prototype of a tinyhawk.
Backsliding instead of progress in almost every way.
Ok where should i start
1. much too expensive
2. much too heavy
3.Electrically, everything at or above the limit (motor connector only approved up to 3A)
The Mobula 6 (Runcam Nano 3) incl. 4x1S lipos costs just € 67 (with code) and weighs under 20g.
Should I get the emax tiny hawk 2 set or the eachine novice 3 set?
Ehm i think novice bcause i only had the flightcontroaler on the TH 1 month, its total worthless when you are a bit of a noob flying 2S
I'm having a lot of interference with my video while flying inside. I'm not having that problem outside. I'm not having that problem with my other quads inside. Anyone have any suggestions to help with the video?
I think it could be wifi interference. It also runs on 5.8G
Great review . Merry Christmas and count on me for continued support in 2020.
😎👍
Is it faster, slower, or about the same speed as the tiny hawk 1 on 1s?
Faster!
Damn you have a nice home
have a good one Andy
Fantastic review