It is important to note that you MUST have the proper bolt carrier (the slide portion) for this to work. If you have a base model such as a S&W M&P 15, you will have to get a compatible slide. Easy enough, have fun!
It is the companies that sell non full auto non mil spec BCGs that are to blame, not the trigger companies. Like going with Nitrided barrels instead of chrome lining them too many companies cut all sorts of corners just to make another dollar in profit on a $750-$2000 Dollar rifle
It is still a semi auto so it's all in how fast you pull the trigger. You still have to pull the trigger for each round, that's how it passes the ATF laws. Since it is a forced reset, by using the bolt carrier group, it resets quicker so you can squeeze quicker. If you hold the trigger back, you're still only shooting one round.
My friend got one today and it has 1/2 mm play on either side of the trigger unit inside the PSA PA-15 MULTI lower. The locking trigger pins did not come with the side bar, and also have some play. The whole unit rattles around in his AR, which is a little disconcerting. I understand he wrote to WOT directly asking for advice on shimming or where to get the sidebar locking trigger pins. As it is now, he won't use it, and I don't blame him. (edited for type of lower)
I have the same issue in my PSA lower. I took mine shooting and could only get it to cycle a few rounds at a time. Not sure if it's the play or something else. Please let me know what WOT says to your friend
mine didnt come with the anti walk pins either. didnt think about shimming but i wonder if the kns anti walk pins will work i emailed as well but didnt get a chance to take mine out yet
i got some small washers from harbor freight so you may be able to get them from amazon or a local hardware store and shimmed both sides. not as cool but took out the wobble until i get the anti rotation pins. id suggest bringing your screws to make sure they fit through the hole and the head will secure them in place. you can always file them down like you would a shim if the spacers are too fat. good luck
Update: my friend ordered anti-walk pin kit with external support bar, like WOT shows in their video. He installed it, and it did make it a bit more stable, but not stable enough, as trigger assembly will still rattle around in the lower. He ordered a shim kit from the internet, with an assortment of thicknesses, and will try shimming it when it arrives. When he lets me know the results, I'll post an update.
I found your install video helpful. It would be extremely helpful if you can do another one with close up video of install for the vision impaired customers like myself
Uhhh,.........Louis......it is EXTREMELY important that we get as many women as possible involved with firearms. Just a suggestion but you might want to avoid pissing off some of the more "sensitive" types of women that might take your suggestion badly....just a suggestion sir.
@@caseymath8149 I speak from the heart. You are correct about getting more women involved. I need to order another WOT since the one I replaced was so successful at range my sister confiscated my Smith and Wesson MP15
@@mrrod3004 WTF u talking about? Rare Breed NEVER stopped for one second. They are making and selling FRT15 triggers like hot cakes. They DID sue the ATF and may win. The based owner is a very ruthless competent lawyer who has all his ducks in a row before any production ever started.
@@BigDaddyUnlimited Use a tiny bit of the wifes nail polish...clear preferably.....works perfectly. Holds tight yet enables you to undo whatever without too much effort......and its CHEAP, especially if you don't tell the little lady.
So wot use basic semi safeties? Unlike binary triggers with full auto safeties that have the third position? Wot triggers only have the two safe and semi auto safety spots?
Got a question,alot of folks having trouble with these...are you using an auto bolt? And also seems like alot think these are binary triggers,read "it dont double tap ,its junk!!" Just curious if this is the main complaints or?
yes these need a m16 bolt carrier, so do the frt. half the people think its a binary when they buy it half of the other half are missing one of the items: *Full-Auto Bolt Carrier Required. *Heavy Buffer (H2, H3 or T3 BUFFER) Recommended. *We strongly recommend a qualified gunsmith install this trigger. *In the majority of setups, the FRT-15 is plug-n-play with a heavy buffer. Tuning may be required.
Just got mine and everything seems fine except the included anti walk pins. one of the pins on one side literally doesn’t have threads so one screw won’t go in. Had to order aftermarket anti walk pins. Hopefully they’ll work🥲
@@mcopilot wow. Mine came with the pins and one without threads, mine didn’t come with the bar. I emailed and DM’d them and still haven’t heard anything back… hope is fading🥲
I wouldn't have a rifle such as this or an AK without a chrome lined bore. It is BS that it negatively effects accuracy unless its done by Bubba and Brothers AR15 Company or some such. FN makes incredibly accurate chrome lined barrels and every service members rifles feature chrome lined barrels........chrome is HARDER than steel and a LOT harder than copper or brass much less lead.
I've tried every buffer and spring I can think of and it still has 1 to 3 hammer follows per magazine. Will these not work with steel case ammo due to it having a tendency to be under loaded?
It should be fine with supersonic 300 Blackout, but getting it to run with subs might be a bit tricky. If you run a suppressor it would be easier to get the subs to run. Mine runs well with 7.62x39 which is similar to supersonic 300 Blackout.
I don’t like that it doesn’t have a third safety select option like a binary trigger does, I don’t want full throttle everytime I go to shoot, I want the option
I installed mine today and it didn’t come with the side bars and after installed the trigger group as to much play in it. It will not fire right!!! I had many rounds with lite primer hits!!! I’m emailing WOT but they are very slow to email back.
It probably varies as to where you buy it. With ammo prices where they are one should really concentrate on putting each round on target rather than seeing who can build the biggest brass stack the quickest
Sorry ATF mine must have gotten lost in the mail, no that was my bump fire stock. No it made it here but was in pieces, I think UPS must have ran over the package. No no, that was my binary trigger. Oh yes, i got it in and I tried it once and shot up all my ammo so I just donated it to Goodwill as a paper weight. Then sold all my guns because I had no ammo left. I am very disappointed I ever ordered one. Now I have no guns. ☹️
It says on the package and the website that an h2 buffer and the bcg being able to be used in the giggle position for the trigger to work properly. Edit. It says nothing on the package about the bcg. But it does reccomend an h2 buffer.
@@deeno313bababa ATF and Patent Infringement issues aside.... if this is plagued by the same spring issue as the FRT then it might actually be worth it.
Interestingly on my Saint pistol with a full auto BCG, the disconnector impacts the BCG preventing the rear upper pin from lining up. I got everything to fit by swapping out my standard BCG with a non-full auto version. **Update** I was able to get the upper seated with the standard BCG by using a 1/16” pin punch. I slipped the pin punch through the narrow slit between the upper & lower and moved the disconnector forward enough to pass the bottom front lip of the BCG while pressing the two halves together.
@@ryanascott You will need a tool to remove your pistol grip, (Typically a long screwdriver or hex key) and a punch to remove your stock trigger pins. Your WOT will include the allen key needed to instal the anti-walk pins that come included in the box.
It should be fine with supersonic 300 Blackout, but getting it to run with subs might be a bit tricky. If you run a suppressor it would be easier to get the subs to run.
Finally took it to the range with my friend. It's everything they say it is. It must have a tight fit, and it will go, go, go. Too bad BDU deleted my comment as to where to get the shims and what kind specifically worked . . . oh well, that's on BDU, not WOT, who by the way, still haven't gotten back to my friend a week later.
I put my WOT in an 80% lower and it had a fair bit of vertical movement so I drilled and tapped an 8x32 screw hole on the left side of the receiver and installed a button head screw. There is zero slop now and it runs perfectly!
@@anthonycalles6004 I put my WOT in an 80% lower and it had a fair bit of vertical movement so I drilled and tapped an 8x32 screw hole on the left side of the receiver and installed a button head screw. There is zero slop now and it runs perfectly!
Is there any intention to negotiate an agreement with Rare Breed for licensing the patent? What happens to those who purchased this from BDU if the Law Suit is won by Rare Breed?
@@BigDaddyUnlimited definitely will. Btw after testing my WOT out, i realised that if you have a heavier buffer and spring, the WOT wont allow the bolt to fully action. Im gonna run more test with different buffers, springs, and gas pressure.
@@Airmanadams standard buffer standard spring and you will rock and roll with no problems, as mine has.. oh and don't pull the trigger to hard. lighter is better
@@BigDaddyUnlimited The the Firearm Cycles perfectly with the WOT installed, Its just the Disconnector portion isn't resetting the trigger with a m16 spec'd BCG.
buy em now, make them a common used good i plan to atleast buy the frt-15, the fr-10 when it comes out, and possibly the graves art trigger since i bought the wot already
That might lead some folks to pay with a prepaid credit card bought with cash and arrange delivery to someplace like your moms old folks home or perhaps a postal drop box purchased with a false name. Use your head and you can avoid the fed.........hey, that rhymed!
Since I don't got the money for a machine gun upper from Fitelite. Anybody think a HBar or a bull barrel would be a good idea to combo with a WOT? I was thinking the extra weight and better heat tolerances might make for a good budget alternative.
If you're actually mag dumping enough for it to be an issue, then yes. But you'll have other problems too most likely like erosion. Shoot for something that is "heavy" profile with fluting and chrome lining for durability and probably 4150 for the barrel material (avoid a chrome-moly barrel material for heat issues).
Just dont do several mag dumps and overheat your barrel. That burning sensation on your left hand should tell you to stop and take a few drinks of beer or soda or somethin
@@caseymath8149 haha well it will have a M60 bipod. Gonna keep my beer drinking hand safe. Check out Klein machining ARPK to have a rough idea what I am going for.
@@ch4osaeternum74 Honestly you'll probably be fine with either, just a chrome molly barrel will wear faster than a chrome lined. The coating is different than the steel used in barrels. Search for chrome lined vs chrome moly. And depending how much you shoot melonite might be good enough too.
Nah man. From what I researched. None of these triggers are approved. But they went by the ATFs definitions which is why FRT is suing and could win. Doesn't mean much I know. But that is all we know.
Just received mine. It came with two stainless colored pins all four screws but no anti rotation bars. The screws almost tighten down if I use a second wrench to keep the opposite screw from turning but screwed in tight they still are 1/16th too loose like the pins are too long and they slide back and forth a bit in my BCM receiver. .
Mine does have play, I contacted wot via email and haven’t heard anything yet. No surprise considering what’s going on, I’m trying to search around on TH-cam cause I saw a video where people are having issues with this. Mine ran perfect through 5 mags first time out. Today I had issues It was loose to begin with but I got that squared away I thought. I’m pursuing getting it straightened out as we speak
Took it back out this evening, only place I have play is the bottom trigger pin. Which definitely doesn’t help the operation of things. It did run however
Ok So I Just Got My WOT Trigger Today Can Someone Please Tell Me Where The Hell In Florida Can I Test Shoot This I Live In Miami Btw Im Willing To Go Anywhere To Shoot This😂
They guy from rarebreed posted a video saying he quit dealing with bdu, he owns the patent for this trigger and bdu started selling another version while having and exclusive deal with him or some crap. It’s on their Instagram if you have that
@@bryanhoell5886 yeah idk what’s true just know what he said in the video, I’ve gotten to the point where i don’t trust a lot of these Aholes that say send me your money so i can fight the machine. They usually end up in a huge house with a private range with all the cool toys while the people get bent over.
@@itsamk18-ish Politics aside, we should all support Rare Breed since they are the only ones taking the fight to the ATF. If they loose the feds will go after BDU everyone who has manufactured or bought these triggers. It's what they do.
WOT needs to state on the packaging that you do in fact need to use a full auto bcg. It will not function at all without it. It says it on BDU's site, read before you buy.
@@BigDaddyUnlimited I just spoke with one of your customer service reps, he explained the problem to me. Symmetrical and asymmetrical. I had to look at it to understand. Almost makes a guy want to weld something. Almost... Thank's for your response though. I'll edit my first comment, no need to make you guys look bad.
Would you like me to show you how to do that easier. 😆 just playin you did fine, just after years of doing this thiers tricks to make this easier so you dont drop springs and detents.
Other than the cool factor, these things are kinda useless. I mean I don't have one, but I thought the general consensus behind "very fast firing" is that it's pretty much a waste of ammo? Hardly any rounds will go exactly where you need, and it really just makes you have to reload more. Idk. Maybe I'm missing something here. Plus aren't these things kinda illegal?
Why did i never think to preassemble the anti-walk pins and bars before. Thanks for the tip!
because you are adopted ryan
It only works for cassette triggers, simp.
ATF comes for Rare Breed & We The People say #GetFucked & we create another version of it & keep on chucking.
I think it's a better version
It’d be great if they were actually helping with the FRT case rather than under cutting them.
@@sentineloffreedomforever1381 i bought it over the frt-15 because for the same price i have a lifetime warranty
@@HansShackleford how much was it ?
@@DJ-cp8hz with the added warranty 379.99
It is important to note that you MUST have the proper bolt carrier (the slide portion) for this to work.
If you have a base model such as a S&W M&P 15, you will have to get a compatible slide.
Easy enough, have fun!
It is the companies that sell non full auto non mil spec BCGs that are to blame, not the trigger companies. Like going with Nitrided barrels instead of chrome lining them too many companies cut all sorts of corners just to make another dollar in profit on a $750-$2000 Dollar rifle
would a full auto bcg be required to run the wot?
A slide huh? Like a Clip? How about a FA BCG?
Also a h2 buffer weight and buffer spring is recommended btw as well as having the full auto bcg
Thanks you just made my night! Thiught i did somethkng wrong. No im just learning lol
Can you fire it in just semi if you want to or is it all go all the time
All go all the time, that's the one thing that to me just makes these range toys.
@@MrMtaylor7210 hmm that kinda stinks
Depends on how you manipulate the trigger
It is still a semi auto so it's all in how fast you pull the trigger. You still have to pull the trigger for each round, that's how it passes the ATF laws. Since it is a forced reset, by using the bolt carrier group, it resets quicker so you can squeeze quicker. If you hold the trigger back, you're still only shooting one round.
@@mediocrates5233 , have you actually used it though? It kinda sounds like you haven’t.
My friend got one today and it has 1/2 mm play on either side of the trigger unit inside the PSA PA-15 MULTI lower. The locking trigger pins did not come with the side bar, and also have some play. The whole unit rattles around in his AR, which is a little disconcerting. I understand he wrote to WOT directly asking for advice on shimming or where to get the sidebar locking trigger pins. As it is now, he won't use it, and I don't blame him. (edited for type of lower)
I have the same issue in my PSA lower. I took mine shooting and could only get it to cycle a few rounds at a time. Not sure if it's the play or something else. Please let me know what WOT says to your friend
mine didnt come with the anti walk pins either.
didnt think about shimming but i wonder if the kns anti walk pins will work
i emailed as well but didnt get a chance to take mine out yet
i got some small washers from harbor freight so you may be able to get them from amazon or a local hardware store and shimmed both sides.
not as cool but took out the wobble until i get the anti rotation pins.
id suggest bringing your screws to make sure they fit through the hole and the head will secure them in place. you can always file them down like you would a shim if the spacers are too fat. good luck
Update: my friend ordered anti-walk pin kit with external support bar, like WOT shows in their video. He installed it, and it did make it a bit more stable, but not stable enough, as trigger assembly will still rattle around in the lower. He ordered a shim kit from the internet, with an assortment of thicknesses, and will try shimming it when it arrives. When he lets me know the results, I'll post an update.
@@GrowBrothers Thank you for the update!
I found your install video helpful. It would be extremely helpful if you can do another one with close up video of install for the vision impaired customers like myself
Uhhh,.........Louis......it is EXTREMELY important that we get as many women as possible involved with firearms. Just a suggestion but you might want to avoid pissing off some of the more "sensitive" types of women that might take your suggestion badly....just a suggestion sir.
@@caseymath8149 I speak from the heart. You are correct about getting more women involved. I need to order another WOT since the one I replaced was so successful at range my sister confiscated my Smith and Wesson MP15
@@caseymath8149 what the fuck are you talking about
Will this work in a CMMG Banshee 9mm?
I own cats, will they be safe if and when the AFT come knocking at my door if I purchase this trigger??? 🤷🏼♂️
Nope
If you live said cats? No they're history
No. They have enough rounds to end all nine lives.
They shut down rare breed 2 months ago which is tje same exact trigger and going after everyone who ordered.
@@mrrod3004
WTF u talking about? Rare Breed NEVER stopped for one second. They are making and selling FRT15 triggers like hot cakes.
They DID sue the ATF and may win.
The based owner is a very ruthless competent lawyer who has all his ducks in a row before any production ever started.
My wot wiggles a little bit inside of my lower is it supposed to do that if not how do I fix it
Can this be purchased via money order ?
Lol, doubtful.. they want your info so they have something to turn over to the ATF.
@@Randy_84 oooof
@@Randy_84 hahahahhaha
No, but our physical storefronts carry them, and they can be purchased with cash there...
@@BigDaddyUnlimited When are you going to open a Store Front in Texas? #Dallas
GREAT JOB
Thanks!!!
Devastatingly informative look for my purchase order soon
Do you make a trigger for the AR10?
do you have them in s&w ar 15 22lr
Is it compatible with JAKL bolt, etc?
Should one use Loctite on the anti-walk screws?
If you do, make it blue.
You can, but you shouldn't use anything stronger than blue. Purple is perfect.
@@BigDaddyUnlimited Use a tiny bit of the wifes nail polish...clear preferably.....works perfectly. Holds tight yet enables you to undo whatever without too much effort......and its CHEAP, especially if you don't tell the little lady.
So wot use basic semi safeties? Unlike binary triggers with full auto safeties that have the third position? Wot triggers only have the two safe and semi auto safety spots?
That's correct. Only 2 positions on the WOT. Safe and Fire.
Nice trigger
Its a good idea to have or get an H2 buffer. I have had to use it in all mine. and it is recommended on the back of the box
I had to use an H3 buffer to get mine to run correctly.
I’m in a h3 buffer and still doesn’t work
I use a H3 Buffer for zero recoil. I also have a BCM and zero fail BCG
@@anthonycalles6004 you probably need a full auto bcg
@@coachpunches55 I have one, the WOT is garbage. Sold it and bought the Alamo 15
Do you need a full auto carrier group?
Will this fit in a sig m400 ??
I think a video on how to tune your rifle to said trigger would be more helpful
Got a question,alot of folks having trouble with these...are you using an auto bolt? And also seems like alot think these are binary triggers,read "it dont double tap ,its junk!!" Just curious if this is the main complaints or?
yes these need a m16 bolt carrier, so do the frt.
half the people think its a binary when they buy it
half of the other half are missing one of the items:
*Full-Auto Bolt Carrier Required.
*Heavy Buffer (H2, H3 or T3 BUFFER) Recommended.
*We strongly recommend a qualified gunsmith install this trigger.
*In the majority of setups, the FRT-15 is plug-n-play with a heavy buffer. Tuning may be required.
Will it work in a sig mcx rattler
Did you have any luck with it
@@pablorodriguez3900 I never tried lol
How to purchase ?
Can I install this in a sig rattler?
Probably not. Pretty sure it relies on M16 bolt carrier to function
@@LibertyOrGTHO buy full auto bolt kit then..
can you guys sell a kit on your website
When I ordered my wot I did not get the bars I got the pins ? Do I need to call someone.
always check customer service regardless what product you called even if its broken new tv screen..
I might suggest mommy..........or the company.
These look cool. Haven’t seen them befote
Why didn’t y’all do a video like this for the rarebreed?
Why didnt the rare breed pay for a video or make a video like this themselves? They of the entitled class?
@@caseymath8149 I’d say the “entitled class” are the ones who answer questions with a sarcastic question and no answers.
Cool trigger
Just got mine and everything seems fine except the included anti walk pins. one of the pins on one side literally doesn’t have threads so one screw won’t go in. Had to order aftermarket anti walk pins. Hopefully they’ll work🥲
May you email or DM us your order number? We'll send you a new set of pins.
@@BigDaddyUnlimited just sent an email!
@@509shooter4 Thanks!
Yep same here I got the trigger with silver pins no anti walk bar, worthless. They need better quality control.
@@mcopilot wow. Mine came with the pins and one without threads, mine didn’t come with the bar. I emailed and DM’d them and still haven’t heard anything back… hope is fading🥲
Is it best to get a chrome lined barrel or heavy barrel to pair with this trigger ?
I wouldn't have a rifle such as this or an AK without a chrome lined bore. It is BS that it negatively effects accuracy unless its done by Bubba and Brothers AR15 Company or some such. FN makes incredibly accurate chrome lined barrels and every service members rifles feature chrome lined barrels........chrome is HARDER than steel and a LOT harder than copper or brass much less lead.
I've tried every buffer and spring I can think of and it still has 1 to 3 hammer follows per magazine. Will these not work with steel case ammo due to it having a tendency to be under loaded?
Why does it not work in 308 or 300blk?
If I had to guess, it's due to the trigger group wasn't designed to handle the extra pressures?
It should be fine with supersonic 300 Blackout, but getting it to run with subs might be a bit tricky. If you run a suppressor it would be easier to get the subs to run. Mine runs well with 7.62x39 which is similar to supersonic 300 Blackout.
Hahaha 0:52 they zoom in on her tightening it up
The focus was all wrong tho
Sheeesh........no wonder ya didnt get laid til ya paid for it when you turned 30.
No dogs were harmed in the making of this video.
I got a big safety concern when loaded hot on safe then flip to fire its firing what could be going on ?
I don’t like that it doesn’t have a third safety select option like a binary trigger does, I don’t want full throttle everytime I go to shoot, I want the option
So get binary..😐
Rare breed selling yalls stuff 🤣🤣🤣
Is this legal in ct?
Will this work on a bca side charging upper?
If I only have a Franklin binary safety (third mode) is that compatible or do I need to buy another safety??
Its all in or safe brother. Can still pull off single shots but you have to be quick.
I installed mine today and it didn’t come with the side bars and after installed the trigger group as to much play in it. It will not fire right!!! I had many rounds with lite primer hits!!! I’m emailing WOT but they are very slow to email back.
Same
That's what you get for buying an FRT knock off.
Sounds a lot like that magnetic buffer thing sold under a guy named Jerry...
Did you ever get it to work? I'm having the same problem
That sounds like hammer follow. Try using an H2 or H3 buffer. I had to use an H3 buffer in mine.
Do you have to change the bolt carrier so it works better and how much is the wide open Trigger
YOu need a full auto bolt cArrier.
It probably varies as to where you buy it. With ammo prices where they are one should really concentrate on putting each round on target rather than seeing who can build the biggest brass stack the quickest
wow that's some lower! the pistol grip bolt comes out and goes in by turning the t handle tool that fits her lower clockwise. lol nice job guys.
I was curious about that too lol
You had to ruin it for me didn't you...😂
You can tell that they cut in the wrong video clip.
Will this work with an armaspec or JP buffer?
I need one ☝🏼
Will the seller destroy all sells records when ATF comes knocking. I'll take 10 but Ive got a money order and PO box uf that works
Lol
All packages are photographed going in and out so if you think a MO and a PO box will save you its foolish.
Sorry ATF mine must have gotten lost in the mail, no that was my bump fire stock. No it made it here but was in pieces, I think UPS must have ran over the package. No no, that was my binary trigger. Oh yes, i got it in and I tried it once and shot up all my ammo so I just donated it to Goodwill as a paper weight. Then sold all my guns because I had no ammo left. I am very disappointed I ever ordered one. Now I have no guns. ☹️
We’re can you buy now?
Lmk if you found a place bro I been looking but I don’t want to buy n get scammed
@@momo_5193 try rare breed
Rare Breed has just filed a patent infringement lawsuit against BDU.
No changing out a buffer or spring needed?
It says on the package and the website that an h2 buffer and the bcg being able to be used in the giggle position for the trigger to work properly.
Edit. It says nothing on the package about the bcg. But it does reccomend an h2 buffer.
You are supposed to use an H2 buffer with this trigger pack
@@caseymath8149 That didn't seem to make any difference for me. It fires the same with the H2 and stock (H1) buffer.
So great you have to buy the warranty separately!
Not worth it !!
@@deeno313bababa ATF and Patent Infringement issues aside.... if this is plagued by the same spring issue as the FRT then it might actually be worth it.
This felt like a ASMR video
Mine didn’t include any anti rotation tabs?
Yup very unhappy rn with what I just bought
Interestingly on my Saint pistol with a full auto BCG, the disconnector impacts the BCG preventing the rear upper pin from lining up. I got everything to fit by swapping out my standard BCG with a non-full auto version. **Update** I was able to get the upper seated with the standard BCG by using a 1/16” pin punch. I slipped the pin punch through the narrow slit between the upper & lower and moved the disconnector forward enough to pass the bottom front lip of the BCG while pressing the two halves together.
We suggest pulling back slightly on the charging handle when closing your upper and lower together, which allows the disconnector to pass the BCG.
Stop giving your money to anti gun companies like Springfield or for that matter any company based out of Illinois
@@BigDaddyUnlimited That was the fix I needed……important
Do y'all have a tool list?
Joe Biden
Kamala Harris
David Chipman
Chuck Schumer
Gavin Newsom
Andrew Cuomo
Nancy Pelosi
Dick Durbin
Gretchen Whitmer
Etc. etc.
@@lostallmymoney2082 jajajajaja I should have been more specific!😂🤣
@@ryanascott You will need a tool to remove your pistol grip, (Typically a long screwdriver or hex key) and a punch to remove your stock trigger pins. Your WOT will include the allen key needed to instal the anti-walk pins that come included in the box.
Where were girls like these when my son was looking for a wife? (Or me for that matter)
That's one of the many mysteries of life my friend.
@@garrett4971 indeed.
they were already scooped up
Be smarter guy awalt
notice the ring on her finger
I watched this video and installed the same. I pulled trigger without ammo, but the trigger doesn't move. What can I do.....
Can it be used in AR's chambered in 7.62x35 (300Blk)?
It can, but it may require some tuning of the rifle.
It should be fine with supersonic 300 Blackout, but getting it to run with subs might be a bit tricky. If you run a suppressor it would be easier to get the subs to run.
Thanks for the info
Yep
what if it dosnt fit do i need a different lower?
Can't wait till mine gets here
Finally took it to the range with my friend. It's everything they say it is. It must have a tight fit, and it will go, go, go. Too bad BDU deleted my comment as to where to get the shims and what kind specifically worked . . . oh well, that's on BDU, not WOT, who by the way, still haven't gotten back to my friend a week later.
What do you mean by tight fit? My anti walk pins won't seem to go in
I put my WOT in an 80% lower and it had a fair bit of vertical movement so I drilled and tapped an 8x32 screw hole on the left side of the receiver and installed a button head screw. There is zero slop now and it runs perfectly!
What did you do? My shit wobbles like no other
All I have is 2 rounds and have to pull the bolt back manually
@@anthonycalles6004 I put my WOT in an 80% lower and it had a fair bit of vertical movement so I drilled and tapped an 8x32 screw hole on the left side of the receiver and installed a button head screw. There is zero slop now and it runs perfectly!
I just installed mine. I can’t get the blot to open I’m pulling the charging handle as hard as I can but I can’t get it to open. What am I doing wrong
😲🔥🔥🔥
Nice
Is there any intention to negotiate an agreement with Rare Breed for licensing the patent? What happens to those who purchased this from BDU if the Law Suit is won by Rare Breed?
When you die you go straight to hell.
Can we all just agree on one thing.... COVID doesn't stand a chance with this trigger.
@Jeff I was thinking more of blasting covid out the air.
what the fuck is COVID?
But will that company give up your info to the atf when they come knocking
Yes
What info? 😉
SHEEP! Get ready for REVOLUTION!!!!
There is no law anywhere saying you have to answer your door, especially after someone shoots the neighbors dog thinking its yours.
@@caseymath8149 I meant with a warrant
Mine did NOT come with anti rotation bars
Mine did neither, I think there’s two versions of anti walk pins, it worked for me though
May you email or DM us your order number? It should have included them.
@@BigDaddyUnlimited definitely will. Btw after testing my WOT out, i realised that if you have a heavier buffer and spring, the WOT wont allow the bolt to fully action. Im gonna run more test with different buffers, springs, and gas pressure.
@@Airmanadams standard buffer standard spring and you will rock and roll with no problems, as mine has.. oh and don't pull the trigger to hard. lighter is better
I didn’t get pins!!! Up in the mountains putting it together now I’m fucked. Thanks.
Got mine, just doesnt seem to work, Only shoots 1 round that Im stuck with a dead trigger.
Have you tried a heavier buffer weight?
@@BigDaddyUnlimited The the Firearm Cycles perfectly with the WOT installed, Its just the Disconnector portion isn't resetting the trigger with a m16 spec'd BCG.
Is this ct legal ?
Connecticut?
@@MrFishyLips yes
Wait till next week The ATF will come for these triggers and we will be screwed again
buy em now, make them a common used good
i plan to atleast buy the frt-15, the fr-10 when it comes out, and possibly the graves art trigger since i bought the wot already
Oh yes. Godzilla is coming. These dopes just dont get it.
That might lead some folks to pay with a prepaid credit card bought with cash and arrange delivery to someplace like your moms old folks home or perhaps a postal drop box purchased with a false name. Use your head and you can avoid the fed.........hey, that rhymed!
Since I don't got the money for a machine gun upper from Fitelite. Anybody think a HBar or a bull barrel would be a good idea to combo with a WOT? I was thinking the extra weight and better heat tolerances might make for a good budget alternative.
If you're actually mag dumping enough for it to be an issue, then yes. But you'll have other problems too most likely like erosion. Shoot for something that is "heavy" profile with fluting and chrome lining for durability and probably 4150 for the barrel material (avoid a chrome-moly barrel material for heat issues).
Just dont do several mag dumps and overheat your barrel. That burning sensation on your left hand should tell you to stop and take a few drinks of beer or soda or somethin
@@jackshett what's the issue with chrome mollee and heat?
@@caseymath8149 haha well it will have a M60 bipod. Gonna keep my beer drinking hand safe. Check out Klein machining ARPK to have a rough idea what I am going for.
@@ch4osaeternum74 Honestly you'll probably be fine with either, just a chrome molly barrel will wear faster than a chrome lined. The coating is different than the steel used in barrels. Search for chrome lined vs chrome moly. And depending how much you shoot melonite might be good enough too.
I guess it would be silly to ask if WOT received a letter of approval from the ATF?
Nah man. From what I researched. None of these triggers are approved. But they went by the ATFs definitions which is why FRT is suing and could win. Doesn't mean much I know. But that is all we know.
I emailed,they said waiting for atf approval
@@hydrocutty Good. That's Real Good!
My anti-walk pins looks nothing like the ones shown, they are loose in the receiver
Same… mine is loose
I managed to fix mine with a little genius ingenuity. Now it fits absolutely perfect. Gunna test it out tomorrow
@@zLightmare what was your genius ingenuity?
Heading to the range rn though. Praying the overseer isn’t there today
For some reason my replies to your comments aren’t being posted..
Just received mine. It came with two stainless colored pins all four screws but no anti rotation bars. The screws almost tighten down if I use a second wrench to keep the opposite screw from turning but screwed in tight they still are 1/16th too loose like the pins are too long and they slide back and forth a bit in my BCM receiver. .
Heard companies are making AK, 10/22 and SP5 FRTs too!!
Can purchase her at Big Daddy Unlimited?
Nope, Big Daddy just puts all this info out for the hell of it.
wtf! mine didn't come with any pins, bars, screws, nothing. just the trigger :(
There have been reports of some of the shipped pins being undersized. Check yours. Your installed trigger pack should have zero play.
Mine does have play, I contacted wot via email and haven’t heard anything yet. No surprise considering what’s going on, I’m trying to search around on TH-cam cause I saw a video where people are having issues with this. Mine ran perfect through 5 mags first time out. Today I had issues
It was loose to begin with but I got that squared away I thought. I’m pursuing getting it straightened out as we speak
Took it back out this evening, only place I have play is the bottom trigger pin. Which definitely doesn’t help the operation of things. It did run however
Noice
When automatic weapons basically have become a thing or the past.
Any word on the lawsuit that this is based off stolen intellectual property?
If all gun smiths looked like her, I'd stop doing my own smithing!
😎🇺🇸
Why so much secret on how it works?
it literally works the same as the frt-15 but with a locking bar
Ok So I Just Got My WOT Trigger Today Can Someone Please Tell Me Where The Hell In Florida Can I Test Shoot This I Live In Miami Btw Im Willing To Go Anywhere To Shoot This😂
But are you going to drop this product once the ATF chimes in, like you did with Rare Breed 🙄
Did I miss something? They still sell them on their website
They guy from rarebreed posted a video saying he quit dealing with bdu, he owns the patent for this trigger and bdu started selling another version while having and exclusive deal with him or some crap. It’s on their Instagram if you have that
@@itsamk18-ish not good for BDU if true...
@@bryanhoell5886 yeah idk what’s true just know what he said in the video, I’ve gotten to the point where i don’t trust a lot of these Aholes that say send me your money so i can fight the machine. They usually end up in a huge house with a private range with all the cool toys while the people get bent over.
@@itsamk18-ish Politics aside, we should all support Rare Breed since they are the only ones taking the fight to the ATF. If they loose the feds will go after BDU everyone who has manufactured or bought these triggers. It's what they do.
WOT needs to state on the packaging that you do in fact need to use a full auto bcg. It will not function at all without it.
It says it on BDU's site, read before you buy.
Do you have a full-auto-cut bolt carrier group?
@@BigDaddyUnlimited I just spoke with one of your customer service reps, he explained the problem to me.
Symmetrical and asymmetrical. I had to look at it to understand. Almost makes a guy want to weld something.
Almost...
Thank's for your response though. I'll edit my first comment, no need to make you guys look bad.
@@disgruntledegghead6923 so do I need to buy a m16 BCG or?
@@cooksze0322 If you want the WOT to work, yes. It will not function AT ALL without the proper BCG.
WOT Trigger doesn't work for my Colt M4 Carbine!
This thing has caused me nothing but problems it will fire, rechamber a round then not fire I’m pissed
Have you tried using a heavier buffer?
Dont use so much pressure on the trigger that is your problem! mine ran flawlessly once I learned not to pull the trigger so hard
Try an H2 or H3 buffer.
Rare Breed is pissed
Would you like me to show you how to do that easier. 😆 just playin you did fine, just after years of doing this thiers tricks to make this easier so you dont drop springs and detents.
0:50 They show her tightening the screw to remove the grip. Bahahaha. Righty tighty.
Other than the cool factor, these things are kinda useless. I mean I don't have one, but I thought the general consensus behind "very fast firing" is that it's pretty much a waste of ammo? Hardly any rounds will go exactly where you need, and it really just makes you have to reload more. Idk. Maybe I'm missing something here. Plus aren't these things kinda illegal?
Blue loctite