Thank you for the professional in depth diagnosis and repair videos. There is value in sharing the struggle of modern mechanics as we strive to keep cars alive in times such as these. Take care.
Doing this job, I removed the ac compressor, no matter what I did the same bolt that broke on you broke on me. I was able to heat it, spray it and repeat. Got the bolt out. This one is not bad, three weeks ago I also did the chains on my 2012 tundra with the 5.7. A little more involved but it wasn’t too bad.
I really appreciate the struggle with rust you northerners deal with. When I had with the occasional rust bucket (wayward snowbirds) it was troublesome.
I have taken my car apart 7 times I put 10,000 miles on my timing chain I took it apart again and found out my timing cover was broke replaced that and the tensioner guide is a pain because if u get any slack the chain moves it was in time put the whole thing together the cams are in time but the crank moved so I have to re do it again yay I'm so excited
Your right to double check the way you did!!! I put the timing chain cover/pulley on to verify the lower timing marks - the marks on the lower gear does not really line up with the seem in the crank anyhow. ON the top it was "9" links between the cam marks. It kept wanting to skip a link. If you have the top chain marks you can use them but as soon as you rotate those marks will not line back up until you get around 90 rotations.... F.Y.I. this was on a 2.4 from 02 camry.
The colored links will line up again after 70 full revolutions of the crankshaft. I had to check the timing marks and didn't want to remove the cover, so I've ran a simulation using my computer and used the number of links in the chain and teeth on the gears to find out that number. Checked in my car and it did line up again after some 40ish turns on the crankshaft. Then I used an inspection camera to check the bottom mark.
How did you get timing cover on the side back on? Did you need to touch the ac hoses or the condenser at all to get it back? Also did you put the sealant on both the cover the engine?
On my 2010 Toyota Corolla repair manual said to release tensioner hook turn crankshaft to counterclockwise then clockwise. Now I have 2016 Toyota Corolla 2xr-fae should turn clockwise to release the hook
Hi Phillip, great videos 🙂. I have a Toyota Corolla automatic sedan ZRE152R with a 1.8L 2ZR-FE engine. I'm trying to decide whether to replace the head gasket (which means I'll need to remove the timing cover) or install a second-hand engine. I live in Sydney Australia but when I tried to find the DIY Workshop manual on the AlldataDiy website you referred to in comments it said Alldata is not available in your Country/region. I may need a kind soul to email me a copy as I'm sure the engines2ZR-FE engines are identical in the USA and Australia. I've watched TH-cam videos of head gasket replacement (takes 12 hours) and also engine replacement (takes 8 hours and more expensive) - both do not look easy. My car started vibrating on idle and made knocking/pinging noises on acceleration when going uphill only. Oil is not being burnt or lost. The same with coolant as the level doesn't drop. There is no visible external leak of the head gasket. I tested compression and cylinders 1 & 2 are OK but 3 & 4 have identical low compression. So I assume the head gasket between those two cylinders is blown. I'm inclined to try the head gasket replacement but not 100% sure. Would you know of another source for the DIY Workshop manual for the 2ZR-FE? Would you have a copy to email? Cheers, Jim
Thanks for watching. You are probably correct that you have a blown head gasket with two adjacent low cylinders. Replacing the entire engine with a good used one is technically less challenging. Whether to fix yours or replace it depends on a lot of factors... Is a used engine available, how many klms on yours? General condition on the rest of the vehicle. You will need quite a few parts and possibly cylinder head work once apart. I can help you with selected service information but I can't email you an entire manual. Phils@tbaytel.net is my email address.
Did you have to do anything with the lower alternator mounting bracket in order to get the timing cover off? I've run into the situation where when I went to replace the thermostat, the lower stud on the housing snapped off. I want to take the thermostat inlet housing off to replace but the alternator bracket is in the way.
@@messemphanger yes I removed the alternator bracket
2 ปีที่แล้ว +1
really appreciate the video and the time taken on this repair. I am struggling to find out if I jumped a tooth when i replaced the tensioner on it-- since i was getting chain slap. never heard that they don't fail-- but the chain slap is gone-- however now i am getting a p0016 which indicates that yeah it did jump a tooth or the chain is super stretched. I wonder if I can remove the tensioner and get it back in time without removing everything? Like could i get the chain to go back a tooth by removing tensioner and then manually. I also learned on these engines to not use DENSO plugs. go with NGK i just had to deal with one snapping a denso plug-- never had that happen with NGK and the gaps were way blown out after 30,000 miles on iridium plugs (i installed the denso's and they were torqued right). From my research I am done buying Denso plugs. NGK all the way.
did you ended up fixing it without removing the cover? I finished a headgasket job but I have the code p0015 I might have jump a tooth when I installed the tensioner
2 ปีที่แล้ว +1
@@karlsolitario8013 so i tried and it jumped a bunch more teeth. i am going to try again with someone helping up top holding the cams while i adjust the crank-- but now it is like 6 teeth out at least. Im obviously not going to crank it and im going to pull the plugs so that I can make sure im not going to bend any valves and only move the engine by hand. But yeah I am going to give it a shot. The other thing people do is they replace teh VVT gears on the cams without removing the chain, so if you want to you can take the cams off and reposition them and then tighten everything down. However-- with that-- I figured that is about as much work as just redoing the timing chain anyway-- and I know it probably needs a new chain (on mine at least) because it was slapping before. But yeah I think people need to pay more attention on this engine that removing the tensioner can cause the chain to jump pretty easily and they should really clamp the chain to the exhaust cam before removing tensioner.
2 ปีที่แล้ว
can anyone email me the FSM for a 1.8l DOHC toyota matrix 2009? I want to have it for when I redo the timing chain
You do not release the tensioner lock manually. The instructions state to rotate the engine using a socket on the crank bolt in the COUNTER Clockwise direction and listen for the click as it released the plunger. Then turn the engine Clockwise a few turns and watch that to chains is taut. Also the aligning marks WILL return to the starting pattern but only after several complete rotations of the engine.
you start at the top then the middle bolts that hold the mount. And then work yourself down and up the the exhaust side in your case. I did the 2arfe engine and had factory service manual which explains it all. You should wait at least overnight for the sealant to dry before adding oil and starting the engine. If any codes do come drive it a few miles and they should clear up.
hi eric i have scion tc 2008 i been having some issues the car shake roughly at idle i have replaced vvt valve cam shaft sensor ,crank shaft sensor , i have cleaned the mass air flow sensor i have cleaned the throtter body alternator , spark plugs and coils are good but the car still shakes at idle and code poo16 doesnt go away should i replace the timing change please respond thank you
Techs at Toyota at the aren’t smartest. You have replace the tensioner with that your doing
2 ปีที่แล้ว
So I just Did chains guides and tensioner and still same rattle. Think I could be phasers? It doesn’t rattle on cold start just at like 2500 under load.
Not much else left to change. This is the first one I did and I recommended replacement of everything using oem parts. I won't do it with aftermarket parts since I was burnt before. Sucks you have to take it all apart again.
2 ปีที่แล้ว
@@PhillipBailey i think it is just the intake phaser making noise and i can potentially just do it through the top by taking off the camshafts and keeping it in time using bungee cords and vice grips) what do you think about that?
I’d sure like to see a video of somebody installing a timing chain cover while the engine is in the car. It just seems like all of a sudden it’s installed but the actual process is missing. Does anybody have a video like that? I’ve done multiple searches as has my son.
@b.h.3649 sorry but it's very difficult to video as I'm by myself and there's not a lot of room to work. If it helps make sure all surfaces are free of oil and coolant. Use brake cleaner and a clean cloth. Apply a 1/16" bead of sealant to the engine block and oil pan surfaces. Use grease to locate the o-rings on the cover and carefully lower the cover into place from the top. HTH
@@PhillipBailey Mr Bailey thanks for responding. My son and I still have the timing Chan cover off, but we soaked the compressor bolts with blaster penetrate and let the sit over night. We then removed the bolts and moved the compressor backwards about an inch and tested getting the timing chain cover in. It gave us the clearance we needed but still a tight fit. Out of curiosity what RTV sealant did you use? We currently have a tube from the Toyota dealership. Anyway we’ll see about getting the cover installed today. Sure wish the Toyota engineers had provided about an inch more room. Thanks for taking the time to make and share your video, it was very helpful.
Mr. Bailey, sorry to bother you again. Trying to reconcile use of RTV on both services being joined together. I can understand in certain spots but not completely. Virtually every video I have watched on the Corolla 1.8L, RTV is just spread on both the timing chain cover surface and the block surface respective of thickness recommendations. When you installed your timing chain cover did you RTV both surfaces or just the timing chain cover? Your time and reply is appreciated.
@@PhillipBailey yeah...at TDC with the marks, I noticed the exhaust seemed 1 tooth out. ( I had moved the chain with tensioner out, trying to get the orange marks to line up, not knowing they were for initial build only daaah)...so I figured just the exhaust might of jumped. I put it back together moving the exhaust to 22 teeth (the intake vvt seemed to land between the proper space)and is now throwing P0017, P0015...ran great when I started it up...then the codes came up with the motor surging as the ECU checked learned data. I cannot figure this out by myself without a shop scope tool to corelate the 2 cam positions vs crank sensor...or it could be the aftermarket exhaust vvt...or I can take the timing cover off...a little knowledge is dangerous...the start up rattling is gone though...lol
So how hard can this be?? We know it's at TDC...we know where the timing gear marks should line up...seems that the chain from intake down to crank sprocket should be tight...
@@PhillipBailey Hi Phillip, was that because you have trouble with dismantling? broken bolts etc? Or because you took your time as you were making an instructional video too?
Thank you for the professional in depth diagnosis and repair videos. There is value in sharing the struggle of modern mechanics as we strive to keep cars alive in times such as these. Take care.
Thank you so much for taking the time and giving great detail
How did it work?
Great video! A big job for sure! Great work and a very thorough explanation on how to get it done correctly. Keep them coming!
Doing this job, I removed the ac compressor, no matter what I did the same bolt that broke on you broke on me. I was able to heat it, spray it and repeat. Got the bolt out. This one is not bad, three weeks ago I also did the chains on my 2012 tundra with the 5.7. A little more involved but it wasn’t too bad.
I really appreciate the struggle with rust you northerners deal with. When I had with the occasional rust bucket (wayward snowbirds) it was troublesome.
I have taken my car apart 7 times I put 10,000 miles on my timing chain I took it apart again and found out my timing cover was broke replaced that and the tensioner guide is a pain because if u get any slack the chain moves it was in time put the whole thing together the cams are in time but the crank moved so I have to re do it again yay I'm so excited
I feel your pain
Your right to double check the way you did!!! I put the timing chain cover/pulley on to verify the lower timing marks - the marks on the lower gear does not really line up with the seem in the crank anyhow. ON the top it was "9" links between the cam marks. It kept wanting to skip a link. If you have the top chain marks you can use them but as soon as you rotate those marks will not line back up until you get around 90 rotations.... F.Y.I. this was on a 2.4 from 02 camry.
Thanks for stating that: Those colored links will NEVER align again! I tried 2 times without knowing that info
Thank you for spreading your knowledge
Thinking outside of the box on your sling. Great work.
Thanks for the video. Lots of helpful info.
The colored links will line up again after 70 full revolutions of the crankshaft. I had to check the timing marks and didn't want to remove the cover, so I've ran a simulation using my computer and used the number of links in the chain and teeth on the gears to find out that number. Checked in my car and it did line up again after some 40ish turns on the crankshaft. Then I used an inspection camera to check the bottom mark.
@@renedare good to know
How did you get timing cover on the side back on? Did you need to touch the ac hoses or the condenser at all to get it back? Also did you put the sealant on both the cover the engine?
On my 2010 Toyota Corolla repair manual said to release tensioner hook turn crankshaft to counterclockwise then clockwise. Now I have 2016 Toyota Corolla 2xr-fae should turn clockwise to release the hook
Honestly I'm not sure as I didn't do it that way. I recommend to follow the instructions in the manual.
The repair manual is for 2009-2013 ,I m not sure 2014-2019 are using same methods or not.
Hi Phillip, great videos 🙂. I have a Toyota Corolla automatic sedan ZRE152R with a 1.8L 2ZR-FE engine. I'm trying to decide whether to replace the head gasket (which means I'll need to remove the timing cover) or install a second-hand engine. I live in Sydney Australia but when I tried to find the DIY Workshop manual on the AlldataDiy website you referred to in comments it said Alldata is not available in your Country/region. I may need a kind soul to email me a copy as I'm sure the engines2ZR-FE engines are identical in the USA and Australia. I've watched TH-cam videos of head gasket replacement (takes 12 hours) and also engine replacement (takes 8 hours and more expensive) - both do not look easy. My car started vibrating on idle and made knocking/pinging noises on acceleration when going uphill only. Oil is not being burnt or lost. The same with coolant as the level doesn't drop. There is no visible external leak of the head gasket. I tested compression and cylinders 1 & 2 are OK but 3 & 4 have identical low compression. So I assume the head gasket between those two cylinders is blown. I'm inclined to try the head gasket replacement but not 100% sure. Would you know of another source for the DIY Workshop manual for the 2ZR-FE? Would you have a copy to email? Cheers, Jim
Thanks for watching. You are probably correct that you have a blown head gasket with two adjacent low cylinders. Replacing the entire engine with a good used one is technically less challenging. Whether to fix yours or replace it depends on a lot of factors... Is a used engine available, how many klms on yours? General condition on the rest of the vehicle. You will need quite a few parts and possibly cylinder head work once apart.
I can help you with selected service information but I can't email you an entire manual. Phils@tbaytel.net is my email address.
Did you have to do anything with the lower alternator mounting bracket in order to get the timing cover off? I've run into the situation where when I went to replace the thermostat, the lower stud on the housing snapped off. I want to take the thermostat inlet housing off to replace but the alternator bracket is in the way.
@@messemphanger yes I removed the alternator bracket
really appreciate the video and the time taken on this repair. I am struggling to find out if I jumped a tooth when i replaced the tensioner on it-- since i was getting chain slap. never heard that they don't fail-- but the chain slap is gone-- however now i am getting a p0016 which indicates that yeah it did jump a tooth or the chain is super stretched. I wonder if I can remove the tensioner and get it back in time without removing everything? Like could i get the chain to go back a tooth by removing tensioner and then manually. I also learned on these engines to not use DENSO plugs. go with NGK i just had to deal with one snapping a denso plug-- never had that happen with NGK and the gaps were way blown out after 30,000 miles on iridium plugs (i installed the denso's and they were torqued right). From my research I am done buying Denso plugs. NGK all the way.
I'd give it a try. Line up the marks and remove the tensioner. If the chain is a bit worn it might help. You don't have much to lose.
did you ended up fixing it without removing the cover? I finished a headgasket job but I have the code p0015 I might have jump a tooth when I installed the tensioner
@@karlsolitario8013 so i tried and it jumped a bunch more teeth. i am going to try again with someone helping up top holding the cams while i adjust the crank-- but now it is like 6 teeth out at least. Im obviously not going to crank it and im going to pull the plugs so that I can make sure im not going to bend any valves and only move the engine by hand. But yeah I am going to give it a shot. The other thing people do is they replace teh VVT gears on the cams without removing the chain, so if you want to you can take the cams off and reposition them and then tighten everything down. However-- with that-- I figured that is about as much work as just redoing the timing chain anyway-- and I know it probably needs a new chain (on mine at least) because it was slapping before. But yeah I think people need to pay more attention on this engine that removing the tensioner can cause the chain to jump pretty easily and they should really clamp the chain to the exhaust cam before removing tensioner.
can anyone email me the FSM for a 1.8l DOHC toyota matrix 2009? I want to have it for when I redo the timing chain
@ try Alldatadiy.com for information access. It's quite reasonable imo.
You do not release the tensioner lock manually. The instructions state to rotate the engine using a socket on the crank bolt in the COUNTER Clockwise direction and listen for the click as it released the plunger. Then turn the engine Clockwise a few turns and watch that to chains is taut. Also the aligning marks WILL return to the starting pattern but only after several complete rotations of the engine.
Ok thanks I guess I missed that in tge instructions. Thanks for the tip it's much appreciated.
There is a torque sequence for the timing cover. Bolts when you put it back on
Yes there is. Basically start in the middle and work your way towards top and bottom gradually tightening til torqued.
you start at the top then the middle bolts that hold the mount. And then work yourself down and up the the exhaust side in your case. I did the 2arfe engine and had factory service manual which explains it all. You should wait at least overnight for the sealant to dry before adding oil and starting the engine. If any codes do come drive it a few miles and they should clear up.
@@andyg5004 thanks for the tips. I did have to wait for the tensioner so the sealant had overnight to cure.
hi eric i have scion tc 2008 i been having some issues the car shake roughly at idle i have replaced vvt valve cam shaft sensor ,crank shaft sensor , i have cleaned the mass air flow sensor i have cleaned the throtter body alternator , spark plugs and coils are good but the car still shakes at idle and code poo16 doesnt go away should i replace the timing change please respond thank you
More than likely the chain has stretched and will have to be replaced.
Is Canada oem parts more expensive than California oem?
1 question can't seem to find, do we have to worry about TDC and compression stroke?????
or is it set correctly by lines?
If the timing marks are lined up correctly it should be on TGC compression number 1.
Brand new camshaft gear comes unlock in the box. Did you lock the VVT-I sprocket after you tighten the bolt?
No I didn't.
Techs at Toyota at the aren’t smartest. You have replace the tensioner with that your doing
So I just Did chains guides and tensioner and still same rattle. Think I could be phasers? It doesn’t rattle on cold start just at like 2500 under load.
Not much else left to change. This is the first one I did and I recommended replacement of everything using oem parts. I won't do it with aftermarket parts since I was burnt before. Sucks you have to take it all apart again.
@@PhillipBailey i think it is just the intake phaser making noise and i can potentially just do it through the top by taking off the camshafts and keeping it in time using bungee cords and vice grips) what do you think about that?
@ remove the tensioner first and give it a try. I would for sure. Taking the timing cover off again will be time consuming for sure.
I’d sure like to see a video of somebody installing a timing chain cover while the engine is in the car. It just seems like all of a sudden it’s installed but the actual process is missing. Does anybody have a video like that? I’ve done multiple searches as has my son.
@b.h.3649 sorry but it's very difficult to video as I'm by myself and there's not a lot of room to work. If it helps make sure all surfaces are free of oil and coolant. Use brake cleaner and a clean cloth. Apply a 1/16" bead of sealant to the engine block and oil pan surfaces. Use grease to locate the o-rings on the cover and carefully lower the cover into place from the top. HTH
@@PhillipBailey Mr Bailey thanks for responding. My son and I still have the timing Chan cover off, but we soaked the compressor bolts with blaster penetrate and let the sit over night. We then removed the bolts and moved the compressor backwards about an inch and tested getting the timing chain cover in. It gave us the clearance we needed but still a tight fit. Out of curiosity what RTV sealant did you use? We currently have a tube from the Toyota dealership. Anyway we’ll see about getting the cover installed today. Sure wish the Toyota engineers had provided about an inch more room. Thanks for taking the time to make and share your video, it was very helpful.
@b.h.3649 I'd recommend the Toyota RTV or Permatex Ultra Black #59803
@@PhillipBailey Thanks. Have a blessed day.
Mr. Bailey, sorry to bother you again. Trying to reconcile use of RTV on both services being joined together. I can understand in certain spots but not completely. Virtually every video I have watched on the Corolla 1.8L, RTV is just spread on both the timing chain cover surface and the block surface respective of thickness recommendations. When you installed your timing chain cover did you RTV both surfaces or just the timing chain cover? Your time and reply is appreciated.
I think I'm in trouble...the chain will jump with the tensioner out and rotating the crank...right?
Most likely it will
@@PhillipBailey yeah...at TDC with the marks, I noticed the exhaust seemed 1 tooth out. ( I had moved the chain with tensioner out, trying to get the orange marks to line up, not knowing they were for initial build only daaah)...so I figured just the exhaust might of jumped. I put it back together moving the exhaust to 22 teeth (the intake vvt seemed to land between the proper space)and is now throwing P0017, P0015...ran great when I started it up...then the codes came up with the motor surging as the ECU checked learned data. I cannot figure this out by myself without a shop scope tool to corelate the 2 cam positions vs crank sensor...or it could be the aftermarket exhaust vvt...or I can take the timing cover off...a little knowledge is dangerous...the start up rattling is gone though...lol
@sheldonwatt7682 I'd recommend to remove the cam cover and double check the timing marks. This was not a fun job for sure
@@PhillipBailey yeah...trying to wrap head around this one...your vid will help for sure
So how hard can this be?? We know it's at TDC...we know where the timing gear marks should line up...seems that the chain from intake down to crank sprocket should be tight...
This job how much time did you do for this job
This took around 12 hours.
I was Installed the Timing Chin But It is Kringing No Starting
@yarmohammadnoori3183 what are you missing? Spark, fuel injector pulse, compression? Was it running before you changed the chain?
is that the same engine as the 07 yaris??
I'm sorry but I don't know for sure
How long did it take you to do the hole job?
Around 12 hours
@@PhillipBailey Hi Phillip, was that because you have trouble with dismantling? broken bolts etc? Or because you took your time as you were making an instructional video too?
@jim2611 it's a labor intensive job. I did have some corroded fasteners. It was also my first one.
You are kinda wrong, the other one has the mark in the back, if you see this video look for all 3 marks, don’t ruin your engine 👍
nice job
U always put a new tensioner going that deep fool
Please stop