F3 Flight Controller with OSD
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2016
- Review of an F3 flight controller with built-in OSD!
Uses the standard SPRacingF3 hex but uses a USB-TTL adapter for firmware programming. Should be nice for smaller builds with less messy wiring.
Check it out here - goo.gl/8UmXLQ
Link to manual - goo.gl/Wyybxq
MY GEAR:
RunCam2 - goo.gl/UF6Pw7
Xiaomi Yi Action Camera - goo.gl/u30TkK
FrSky Taranis X9D Plus - goo.gl/W6VNL3
Fatshark Dominator V3 Goggles - amzn.to/206Ruwn
What I use to edit my videos - amzn.to/1VJHWp7
What I use to film my videos - amzn.to/1oNXBth
SUBSCRIBE TO MY CHANNEL - goo.gl/b1cZZM
![ลักพาตัว เอาลูกเอิร์นกลับมา...!! [เอิร์นไดเม่]](http://i.ytimg.com/vi/f4NVKlZ5qkk/mqdefault.jpg)
Thanks mate from Australia on the gold coast. Your the only one on TH-cam talking about this controller. Glad I found you. Just bought one of these was worried about how to connect it to my clean flight.
Hi, thanks for the vid..any idea how you can connect this board in PWM to a HK-T6A?
Thanks
hey anyone having any thoughts on why the video signal is going thrue the osd but not doing any overlay?
Nice one just what I have been looking for, thanks.
Hi,nice review.. could you help me about wiring in spracing f3 include OSD? could you share the link? I'm so confused about powering the board,because I already connect 5v power from PDB but the board won't power on, thanks
When i connect the video out to my tx i can see the OSD and its working perfect.. when i connect the camera to the IN OSD is disabled and only camera is visible! do u have the same issue? is there something i am missing?
thanks
can I run a GPS and LEDS at the same time and which port or ports I am running mind on sbus . Thanks
Hi Al, will this bad boy replace the original fc on my arf gt2 200? Other compatible fc options? I need the simplest fc to install possible.
Hi is there any chance you could tell me were to plug board in to use on etc betaflight, inav not having much luck.
Keep having a little green light flickering that it . plug in to another port get same green light and a red flashing one looked for a boot button but nothing on board.
Do i have to power board first please help most gratefully if you could.
Hi, thanks for the video.
At last find some information on this board.
At the moment everything works for me but I can not find information on how to connect an IBUS FS-A8S transmitter.
In a normal F3 this transmitter is connected to the welding points of the UART2 ( TX, Gnd and Positive) but in this plate I do not know where to solder the three cables (Negative, Positive and Signal)
Can somebody help me??
Thank you.
Pretty cool Albert 👍
I have this thing wired directly to the battery using vbat pads, however mw osd will not display correct voltages. it's stuck at 15.3 no matter what I do :(
3D RC Did you end up sorting this out? I've had the fc for a while now and after updating minimosd +betaflight I did something wrong, so now my voltages are constant 16.4V....
im gonna buy this flight controller for my new 210 qav, hope do it right, i 'll see your videos of this flight controller, thanks for teach us.
Thank you for making this video.
Two questions:
1 .How do you flash CleanFlight on this board? I am using the provided USB2TTL adapter with the pins connected as you show but I am always getting a "No response from the bootloader" error. EDIT: Need to disconnect the white cable pin from the USB2TTL flasher and select "Manual Speed 256k" on CleanFlight Configurator.
2. Is it safe to power the board via the VBAT pins on 3S?
Many thanks in advance.
+FrontierNG The vbat pins just detect voltage reading. You still need a 5v source for board power
+FrontierNG The vbat pins just detect voltage reading. You still need a 5v source for board power
+FrontierNG The vbat pins just detect voltage reading. You still need a 5v source for board power
+FrontierNG The vbat pins just detect voltage reading. You still need a 5v source for board power
+FrontierNG The vbat pins just detect voltage reading. You still need a 5v source for board power
ciao,scusa ma non parlo inglese..
Ho la tua stessa FC... utilizzo la MSP come porta di configurazione,la UART2 per la RX e la UART3 per il GPS (uso INAV).
Ho caricato MWOSD ma quando accendo mi dice NO DATA?
Hai qualche idea??
Grazie in anticipo
I just got the board. Updated the FC and OSD software (eventually).
I've quickly checked that the configured OSD display appears via the camera / VTX, but am unsure if there needs to be some software config done to actually get the FC data to be reflected on the OSD i.e. did they simply put a separate MinimOSD on the board which gets the data for display or do you have to configure a UART to allow it to be displayed.
Ideas, anyone?
+normoa you need to configure the UART and enable MSP
Which UART (presumably UART2) and does it require wiring from the OSD port to the UART?
Can you give me a bit more details with the setup? (Presume I'm dumb and you may not go far wrong... :D )
Hi, I assume it is hardwired to a UART, but the question is which UART? (I can not find any documentation on this). Do you perhaps know which port it is connected to? and any specific settings in Betaflight needed? Thanks
Who know how can I connect this flight controller to the receiver flySky iA6 or iA6, only connected auxiliars channels, not connetec the pitch, Roll, throttel and Yaw... who can help me please.. Thanks
Hello Kim, I got this board but it came with no instructions to do all connections, I'm still green on this things, Can you explain all about this board to make it fo fly!!!...thank you
There is a link to the manual in the description. I have several other videos on flight controllers in my channel as well as many build videos showing how flight controllers are connected up. This one is not much different from those other flight controllers.
Do you think I can remove the plug and solder the USB port on it?
I'm sure it might be possible but I don't know how to do it myself and you'd need some stellar soldering skills.
I been having issues with my quad after changing motors. Got rid of the wobbles after raising tpa then I figured out how to flash the firmware. But for some reason I have no osd now. All the stitches are turned on in clean flight but still no osd. Do I need to download the osd as your talking about? The timer works but no flight modes or battery voltage Wich I need and no arm disarm. It just flashes and says no data. Help please? Lol
+Ian Rice enable msp on uart1
Albert Kim it is. I been trying to try it to work for days. I been learning allot. Do you have any other ideas? I have figured everything else out but the osd. Thank you for you help!!!
Oh I'm using the flycolor sp racing f3 board. Just thought you should know.
I turned on uart2 and Bam it's all working!!! Thanks man.
idk what to do, do I flash i as a naze or a racerspi
SPracingF3 hex
thx alot man this helped alot
Hi
Can you try if the new betaflight osd tab can control and setup the internal osd of this board? Thank you
+Ananous no it can't. That's for a very specific setup. This hardware is different
it can you have to flash scareb osd
Do you have links to Betaflite and Scareb OSD? WOuld like to try this. I just got this board.
+JF Kerekes sorry I don't know where scareb is
Hello, i have one question. How to boot or flash flight controller?
short the bootloader pads
Eimuks K short the BO pins
Sbus compatible? Manual only shows ppm/pwm
Yes, SBUS works
can you pls help me with this fc ? all is fine but when i connect my lipo the configurator stops working ...what i have to do ?thanks
What do you mean by configurator? The software on Windows? Also, do you have USB and lipo both connected at the same time?
Albert Kim
Yes on windows ! I run btfl 3.01
Spf3 target !
Usb to ttl conected with fc and lipo ....
I can not cal. Esc and endpoints off rx ...
where would you connect a x4r sb on this board?
Use the IO_2 connector for SerialRX. It's shown on the manual which you can download from the product page goo.gl/8UmXLQ
Can you please tell. I badly know colloquial English, because I from Russia. What you need to do to turn the OSD on the controller?
+Виталий Its already on. You have to connect camera and vtx to have it pass the data to the video for overlay.
I'm all hooked up. But betaflight in the tab menu is written: "Your flight controller does not respond to commands menu. It probably means that it does not have an integrated BetaFlight of OSD" in the Flight controller just like in the video(F3 flight controller with integrated OSD).
Виталий anche a me risponde nello stesso modo... Come faccio ad attivare OSD??
Io uso INAV 1.7
Hi sir, thanks for the video, I'm new on drone world and I'm trying to build my first one now, I just bought this board but I cannot find any wiring diagram for this specific one, do you have any wiring diagram to share with me?
click link in the description... the manual is on the product page. it's a PDF file you can download.
Hi, Thanks I just flashed with latest firmware, now I'm going to flash the arduine and then OSD. But on this website doesn't have the wiring for other stuff :(
Perhaps you can be more specific on the "other stuff" that's missing? I'm not sure what you're talking about.
Sorry, I mean I need a general wiring guide for everything using this board, FPV, camera, etc. is there any available?
Sorry, that's the only documentation I'm aware of. For the VTX and Camera, you connect those to VOUT and VIN (stands for video out and video in). It's clearly labelled on one of the diagrams in the manual.
overall thoughts? good FC? what is on the osd? tuning thru osd?
It's good. The OSD is the micro minimOSD so it does all the same stuff that one does. It's just integrated into the one board.
cheers
Do you known purpose of pads marked as "PAL"?
+David Gigauri no sure
Interesting point, I can't find any info about this pads. :) I have same board, but have no time to setup it on second drone.
Thanks for response.
Probably for the osd to enter "pal" mode or "ntsc" mode.
Un-soldered means ntsc, soldered means pal.
That's my guess!
Hi Albert, maybe you can help me,
I can't see my receiver input on Raceflight on this board. I'm connected with sbus from my xsr to the pin 3 on UART3 (ch3).
On Configuration Tab, I set up RX_SERIAL and sbus. On Ports section, UART3 is used for Serial RX and UART2 is used for telemetry.
I can read the battery pack voltage on my Taranis so the telemetry is working but my control input are not working. Do you have any idea?
Thank you
Are you sure you connected to RX and not TX? That's usually a common mistake that people often overlook.
According to the manual: s21.postimg.org/uqm777w13/2016_10_14_17_50_39_R_cents_Google_Disque.png
So, is the XSR getting 5v or 3.3v?
Albert Kim 5v. I should mesure the voltage. but my telemetry is working...
+Vincent 2r2b Hmmm, I'm stumped... maybe try a different UART?
where would I hook up a spectrum satellite rx to this?
There is a 3.3v output documented in the manual on page 1. There is no dedicated spektrum port. You have to grab 3.3v, GND, and RX from one of the UARTs.
so going by the docs it says gnd ch3 and adc1 or 2 for the 3.3v on the Io-2 connector. I think that's right ? thank you very much for your quick response albert!
You can get ground anywhere. The 3.3v pin is the one that's important. Also the RX of whatever UART you choose.
I was excited about this until I realized you had to program the osd with an arduino. I can't stand that crap! Think I'll stick with the PowerOSD Pro osd/pdb
you can program it with the included adapter so no need for extra hardware..
Oh yeah? Well that's a different story then..
Yeap with the included USB-TTL adapter you can program either the osd or the fc , depends on the slot you connect it.. and its easier for later programming to connect the small adapter rather than the usb plug in the quad
Where is the bootloader port in the board
Go to the product page (link in description) and download the manual. Bootloader pads are pictured on page 2.
Albert Kim j i knigfgyhhninmmloin hhuh hjbnnnmmmnhbjmnnmininhbuvy yvcygghhhhhhhhjjjjjjjjjijjjjjkkkkjjj
1103, 1104 motors? Someday?
1104 motors going on the mosquito but my PDB is lost in the mail so there's a delay there. The 1103 will require a custom frame so might be a while. Is there a specific question about those motors I can address in the interim?
I'm searching the web for smallest, brushless, affordable setup. Actual weight of the motors? Wich props this motors can spin without the overheating? Which battery can handle? Some thrust test. Any suggestion for other components? ESC, FC, frame ~100mm or less. And so on. Thanks.
I did a brief overview video on the 1104 motors. They are very similar to the DYS motors. You can probably run them on 2 or 3S lipos with 3020 or 2535 props. They require a special T-style prop. I believe the weight was 5g but I did weigh them in the video if you check it out. I will do an overview video on the 1104 and try and address these questions. Thanks for your feedback.
Here's the video on the 1104 motors - th-cam.com/video/7Zi0pG5gwpo/w-d-xo.html
+Roman Mic for more affordable setup avoid 1104 and smaller. Those are more expensive because the parts are scarce. Go with a 1306 130 size build.
No USB port? Hahaha! That's crazy!
No USB port? Hahaha! That's crazy!
it has usb with included adapter