How to Lower the Front of a D Series PU | First Gen Dodge Ram Ramcharger Lower Control Arms
ฝัง
- เผยแพร่เมื่อ 5 ก.ค. 2024
- Lowering a Dodge D-Series (D100, D150, D200, D250, D300, D350) is probably the easiest project that really changes the look and feel of these old Mopars! This video will show you how, and I have an idea to get my D100 shop truck project just a little lower...
D100 Videos:
• 1975 Dodge D100
Charger Videos:
• 2017 Dodge Charger
VW Beetle Videos:
• 2001 VW Beetle
DIY Projects:
• DIY Home Projects
Fitness Videos:
• Fitness
You can always find me here:
Webpage: www.wjm-industries.com/
Facebook: / wjm.industries
Instagram: @Moonbuilt
Twitter: @BuiltMoon
What I Use To Film:
Canon EOS M50: amzn.to/3aRNRbw
DJI Osmo Action: amzn.to/3aR2E6x
Zhiyun Smooth 4 Gimbal: amzn.to/2YKrkto
Rode VideoMic Me-L: amzn.to/3pUx1RI
Rode VideoMicro: amzn.to/3nBqFng
Rode Wireless Go Wireless Lavalier: amzn.to/2RoROO3
Vijim LED Video Light: amzn.to/3gW5mLV
Thronmax MDrill Zero Microphone: amzn.to/2ZR23cK
AmazonBasics 60-Inch Lightweight Tripod with Bag: amzn.to/2ZxEVzP
Vastar Smartphone Mount: amzn.to/2NE5JMp
Affiliate Links:
Amazon
eBay
Jegs
Printful
Disclaimer: Some of these links are affiliate links where I'll earn a small commission if you make a purchase at no additional cost to you. This helps support the channel and allows us to continue to make videos like this. Thank you for the support! All opinions are my own and presented without editorial input from outside sources.
Disclaimer:
Due to factors beyond the control of MoonBuilt Garage and WJM Industries LLC, we cannot guarantee against improper use or unauthorized modifications of this information. MoonBuilt Garage and WJM Industries LLC assume no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. MoonBuilt Garage and WJM Industries LLC recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of MoonBuilt Garage and WJM Industries LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MoonBuilt Garage or WJM Industries LLC.
Produced and owned by WJM Industries LLC
#MoonBuiltGarage #D100 #Mopar #1stgen #Muscletruck #hotrod #stroker #hotrodtruck #dodge #408stroker #417stroker #408ci #417ci #strokermotor #dodged100 #V8 #moparornocar #dodgetrucks #dodgeporn #dodgebuilt #builtnotbought #garagebuilt #truckbuilds #d100brotherhood #dodgebrothers #moparnation #rattymuscletrucks #rattymusclecars #moparmafia #Americanmuscle #trucklife #garage #garagebuilt #garagelife #garagefun #garagenight #oldtrucks #projectcar #projecttruck #streettrucks #garagefun #Workshop #Welding #Fabrication #tools #Hotrods #Musclecar #Musclecars #Hotrodsandmusclecars #Hotrods #Homebuilt #garagelife #oldcars #oldtrucks #madeinusa #americaclassic #oldschool #horsepower #streettrucksmatter #badass #patina - ยานยนต์และพาหนะ
![เจอประจำ ตอน เปิดเทอมวันแรก [EP.29]](http://i.ytimg.com/vi/eFK-B836i60/mqdefault.jpg)
Best video I’ve seen on the subject
Thanks!
You made a Moparman happy after watching this video. Thank you for the info and the great video.
Glad you liked it!
Dude, you and I think so much alike, it's crazy. Chopping up a set now for the D100 build...good to see ya
It worked out a lot better than I thought it would lol
Buen video mi tío!!👌
Nice work mate. Great videos.
As an owner of a 77 1/2 ton stepside D100 in Australia videos like this are a great resource. There’s very little info over here for these let alone parts!
Mine rides terribly due to a dodgy drop so will definitely be doing this although the aftermarket Rekudo arms are tempting as by the time I ship over the van arms it works out near the same.
Thanks! This truck is why I started TH-cam...I was having problems finding info. Is there no way to find used van arms there in Australia? My first pair I bought new, but I see a good number of B-series vans in the salvage yards, and the same arms were used for a number of years, making them semi-easy to find, and WAY cheaper than buying new.
Great video! Thanks!
You bet!
I own a 1974 International D series pickup, 2wd. They made very few 2wd D series in 74/75 then IH went under. My brake rotors are obsolete! Horror! I find that knuckles from an 87 Dodge pickup fit my suspension,kinda. Tie rod mounting location is slightly different, but this issue is fixable. Anyhow.... So, I actually cut out the entire front frame section out of the 87 Dodge. I'm starting to think my best option is to mount the Dodge suspension onto my IH frame. To begin with, the two suspensions are very similar in design. At first glance you may think my IH was built with the Dodge D series 2wd suspension. When i pull my IH control arms, I'll find out if Dodge control arm bushings fit my IH control arms, upper and lower. If they fit, I'm going to stay with my IH control arms with Dodge knuckles. If not, I'll put the Dodge control arm mounts/suspension etc onto my IH frame. Parts will always be available! Plus, i can use the Dakota lowering spindles if i wish, or the van lowers....
Any how... This video was a good watch. Thanks.
I did a detailed write up and posted it on Moparts years ago. Photobucket screwed up all of the picture links. I didn't have to notch my lower control arms like you did. I did have to grind a little metal off of the lower control arms around the bushing because they were hitting the bracket on the truck frame. The bolts and holes wouldn't line up. I think I had under $100 in the whole drop including new ball joints, paint, and U-bolts for the rear axle flip.
3 " Drop spindles from first gen. Dakota will also work on these trucks with a small amount of mods ! I have 2 sets but haven't got around ta doin it yet ! I knew about the lower control arm swap from several years ago !
I've seen some info about the drop spindles for Dakotas, but this seemed to be the easiest route, as well as the cheapest
hey, diggin the video and info. so if I wanted to use the d150 control arm on my b250 to gain some height, id only need to reverse engineer what you had to do? thanks I appreciate it.
I would think that should work...
You didnt have to put longer adjustable upper a arms on to keep your camber correct? thanks for videos
No need
Can you tell me more on the Lowe control arms and the measurement for the holes drilled so I can lower my 86
The lower arms are from a b-series van...up to the mid or late 90s. You can take the measurements for the holes from your original control arms and transfer that to the b-series control arms....I don't recall the exact measurements, but it's not difficult to figure out
Shorter Dakota coils will also work I believe !
The problem I could see with going to a shorter spring would be bottoming-out the suspension, but I can't say for sure since I haven't tried it
Doing this same project, tried the d300 truck lower control arms which are deep but the balljoint hole and stud is huge compared to the d100 stuff
I haven't heard of anyone using the d300 stuff, but makes sense....maybe they are larger since the d300 is a one-ton...? Maybe...maybe I'm wrong.
Higher gvw is what I'm finding out
I installed van lowers on my d150 used new standard rate springs and I have only about an inch or so between tire and fender
I used heavy duty springs on mine when I originally rebuilt the front, so mine sat a little higher with just the stock van lowers
Could you apply the same work to a stock lower instead of buying a b series just put a 4 or 5 inch cup in?
Probably...I just didn't have my old stock lowers any more, and I didn't want to tear up my B-Series lowers just incase it didn't work
I was just going to use pipe. Go to a fire protection company or supply like Ferguson. 2 one inch pieces shouldn't cost much.
Buenas noches amigo me podrias pasar las medidas para aserlo mismo en mi troca
Can you still run 295/50’s w 10in rims on the front without rubbing?
Not really sure...im currently running 275/60r15...but I want to go to a 17" wheel but keep the same overall size
hey man how much would you charge to make some for mine 1983 d150
Yeah...uh...I'm ok with risking my own life with my welds....I don't wanna be responsible for someone else 🤣
@@MoonBuiltGarage well i can understand that man i wish i was as talented as you but thanks for getting back to me
Hey man the lower ball joints will not go into my spindle all the way what kind did you use ?
I used the balljoint listed for the D100, but I think they are the same. You should be able to cross-reference the parts at Rockauto or other sites
@@MoonBuiltGarage I got ball joints for my d100/ramcharger and it fell right through the lower control arm that’s why I was confused
@@brandonnelson9392 I think they come in both screw-in and press-in....mine are press-in...
@@MoonBuiltGarage I just found out the guy sold me ball joints for a 99-03 ram 3500 van so that’s why the ball joints are giant thank you so much for the replies tho really appreciate it
What shocks are you running on this?
They are just stock replacements from KYB that I got at rockauto
You ramble alot get to the point geez..
I'll be sure to keep your profound, constructive criticism in mind for my future content