Great content video audio commentary tutorial editing very easy to listen follow along & understand for me but apparently NOT for others got huge migraine from reading comments & questions Thank you Sir you definitely have plenty of patience
Almost everything asked in the comments was well explained in the video 😊 thank you. I'm gearing up to record a bunch of new videos. Please subscribe, thanks.
Thanks for this video. I have this same setup in my car. Two 4 ch amps and one mono amp. I was struggling to find out why my rear 6x9 weren’t playing as loud as my front speakers on my 4 channel amp. I ordered a 8 channel Dsp to fix the problem and you just explained how to do it.
This helped me out. I couldn’t figure out why I wasn’t getting sound from my eq to dsp to amps. I had a splitters for l and r going into A and one into B. I
I had my dsp hooked up for awhile now but recently I been getting the limiter light coming on when I turn the volume up but the actual amp isn’t clipping. I checked my dsp and the limiter function is off the other weird thing is my mid bass is hooked up to channel 1 but the limiter light comes on Channel 2 and I do not have anything hooked up to channel 2. Any help will be greatly appreciated.
I understand the concept but I’m having trouble finalizing my build. I have the PRV DSP 2.8, a PRV SQ6000X Amplifier, a PRV SQ3500X Amplifier and a PRV Q1200 Amplifier. They’re all single channel… Which RCAs should I get? I plan on installing all four components onto a single amplifier rack. The plan is to use the 6000 to power 2 Subwoofers, the 3500 to power 6 mids and the 1200 to power 6 tweeters.
PRV recently released some high quality shielded RCA cables.. they're very nicely built. Check them out. You can really use 1 RCA per amp. With only 3 amps, you have enough outputs on the DSP to run 2 to each, but it's not necessary.
I have a PRV SC-20FT Pro 2 Channel RCA cable and I also bought this DSP. Being that the DSP only has 2 inputs… which output on my head unit do I plug the RCAs into? Front, Rear or Sub out? Or do I need Y splitters? If so, how do you recommend I wire the head unit and DSP for optimal performance?
Hey bro after setting the gain on the dsp or in my case my Pac e.4 loc which also has clipping lights, would you then set gains on your mono amp with oscilloscope as normal??
You would just connect each output to each input on the amp. You would need to share at least 2 channels on one input with 1 of the DSP outputs as there wouldn't be enough.
The routing doesn't matter if it's mono or not. You can have one mono amp doing just a left signal and another doing just a right signal using the routing feature!
Sorry to necro, but hopefully you can answer my question. For inputs, is it only low level, or can it use high-level input as well? I ask cause i syill use an oem player😊 thanks
With just this unit, it is not possible for high level input. However, with an LOC (line out converter( that provides an RCA output, you can certainly use this DSP with your factory radio.
Im working on a whole new system using an indash eq with the prv 2.8x dsp and a 5 channel amp (memphis Audio VIVseries Belle) but not using the 5th sub channel (cause i ended up getting a different sub then originally planned cause got a really good deal on sub and the amp). The front channels are running my tweeters the rear channels are the mids. And a mono amp (Memphis Audio VIVseries 2200) to power the VIVseries 14 inch sub. So going to the amps from the dsp channel 1 and 2 go to the front channels (1 and 2) on the amp then channels 3 and 4 go to the rear channels on the amp (3 and 4) then channels 5 and 6 go to the mono amp (5 and 6) is that correct?
Can any one messege me now need help setting up dsp! Have it running from front rca’s of kenwood ddx26bt and out from prv 2.8 to skar rp150.4 with 4 channels and 2 to taramps 1800.1 d
Man I'm doing the same exact thing!! One mono and one 4ch and getting the PRV DSP 2.8 soon here and just wanted to know if you had finished your install and how it worked out for you and a brief rundown of how you did the RCA wiring ..So is it one set of RCA from HU to DSP then with the 4ch amp I combine all the left signals into one output of the DSP and the same for the right ?? And then my sub amps left and right combined into one to go into 1 output of the DSP? Obviously using y connectors to combine Lefts and rights individually into there own one solid RCA to go to DSP outputs. Any help will be much appreciated!! Thank you in advance!
@@mikebugarin3339 i ran 1 set from hu front ch to dsp. 1 y splitter to 2ch rca to mono amp. An then 2 sets of 2ch rca to 4ch amp. Ordered 3ft rca's from Skyhigh
@@mikebugarin3339 set ch1 to A+B signal for mono. Set ch2 to A. Ch3 to B. Ch4 to A. Ch5 to B. But you can pick whatever chan you want to go to whatever amp. 1 - 4 to 4ch amp an Ch5 to mono. It was just easier for me to arrange it that way. I didnt want to uave my rca crisscrossing so i ran my mono outta ch1 an my 4ch amp outta channels 2 - 5
@@mikebugarin3339 you can order certain length rca's from Skyhigh. I just guessed the length i needed. 3ft was more than i needed. Can buy Y splitter as well. Think it was like $28. 1 y splitter an 3 2ch rca's. Price goes up with the length of rca's
Great content video audio commentary tutorial editing
very easy to listen follow along & understand for me but apparently NOT for others
got huge migraine from reading comments & questions
Thank you Sir you definitely have plenty of patience
Almost everything asked in the comments was well explained in the video 😊 thank you. I'm gearing up to record a bunch of new videos. Please subscribe, thanks.
Thanks for this video. I have this same setup in my car. Two 4 ch amps and one mono amp. I was struggling to find out why my rear 6x9 weren’t playing as loud as my front speakers on my 4 channel amp. I ordered a 8 channel Dsp to fix the problem and you just explained how to do it.
Excellent!
Does it matter what output on the head unit you use. Mine has front,rear and sub out and I want to run a four channel for doors and mono for sub?
@@coreymcfarland3112Got a answer??
Thanks so much, just understand about how the routing feature works with 1 rca and sliters 👊
Thanks 4 the vid it was helpful, I would like to see more vid on Settings the features on the dsv
Great work keep it up
Watching your videos and information I have to place my order for 2
This helped me out. I couldn’t figure out why I wasn’t getting sound from my eq to dsp to amps. I had a splitters for l and r going into A and one into B. I
I am glad the video helped you to sort it out. Please subscribe for more helpful videos.
Can you make a video showing how to connect the cables to the amplifier?
Yes, soon
Thank you because no one made a video
That really helped me I appreciate the break down now could do a video including a epicenter in the system?Maryland showing a little ❤
Epicenter would go between the DSP and the amp 😎
Awesome info. I have a 4 channel and an 8 channel amp I’m using for my highs n mids, could I use the prva for this set-up? How would I run it if so?
Good video man 💯👏🇸🇷✌
Thank you so much!
I think i should get maybe like 25% credit for this video lol
You should make a video on how to set up a dsp to a 5 channel amp I’ve looked all over and cannot find. Thanks
Each input on the amp gets an output from the DSP. Very simple.
Thank you 🙏
I had my dsp hooked up for awhile now but recently I been getting the limiter light coming on when I turn the volume up but the actual amp isn’t clipping. I checked my dsp and the limiter function is off the other weird thing is my mid bass is hooked up to channel 1 but the limiter light comes on Channel 2 and I do not have anything hooked up to channel 2. Any help will be greatly appreciated.
So im back lol. Lets get a vid on the graphic input eq an the parametric input/output eq lol ill be good to go then lol
Can you burn anything if connected wrong signal? Or would it jus don’t play ?
I just bought one can't wait to get it. So technically i can 8 amplifiers for different stages in my truck then 1 amp per output?
Yes
make a video on the gain and limiter feature
What if I have a 3 pre amp channel radio which one would it go to
I understand the concept but I’m having trouble finalizing my build.
I have the PRV DSP 2.8, a PRV SQ6000X Amplifier, a PRV SQ3500X Amplifier and a PRV Q1200 Amplifier. They’re all single channel…
Which RCAs should I get? I plan on installing all four components onto a single amplifier rack.
The plan is to use the 6000 to power 2 Subwoofers, the 3500 to power 6 mids and the 1200 to power 6 tweeters.
PRV recently released some high quality shielded RCA cables.. they're very nicely built. Check them out. You can really use 1 RCA per amp. With only 3 amps, you have enough outputs on the DSP to run 2 to each, but it's not necessary.
How will this set up play stereo
Make a video on what to do to your radios settings and amps settings when u install a dsp
Yes will do thank you for the tip
@12 Volt Fever any input on this video yet?
I have a PRV SC-20FT Pro 2 Channel RCA cable and I also bought this DSP. Being that the DSP only has 2 inputs… which output on my head unit do I plug the RCAs into?
Front, Rear or Sub out? Or do I need Y splitters? If so, how do you recommend I wire the head unit and DSP for optimal performance?
Front
Many thanks.i would like to see the settings how things work.
Check my channel for the DSP video I show the routing feature inside the DSP
Whats your email addres
My head unit has 3 rca outputs. Sub out Rear out Front out. Which one should I use for the best signal? In you opinion.
Front is fine
What of you only use mono amps for both mids and the drivers/tweeters, still need to use the routing feature?
You do not need to use the routing feature with mono amplifiers unless you are adding 2 equalizers or trying to do stereo sound.
So with mono amps you need one amp for left side and one for right side correct ?
Bro, why my prv prcessor clips.
Sincerely I'm not using a good power supply, which power supply do you recommend me im installing it at home .
More gain output on the amplifiers
@@12voltfever thanks , bro.
When tuning a processor do you send a flat signal to the processor or do you tune from the processor and deck pionner to be exact?
Signal should be flat. Amps should be flat also
@@12voltfever what do you mean by “amps should be flat also”? All gains down or half way point?
Yes select flat on the dsp
Hey bro after setting the gain on the dsp or in my case my Pac e.4 loc which also has clipping lights, would you then set gains on your mono amp with oscilloscope as normal??
Yes, set the amp gains as you normally do
Please make a video on how to hook up a dsp to a 5 channel amp.
I’ve looked all over and can’t find one.
You would just connect each output to each input on the amp. You would need to share at least 2 channels on one input with 1 of the DSP outputs as there wouldn't be enough.
Bit I'm using 2 different types of mids which the channel left and right wont match the specs of the mids. Can you help me?
I have 4 midrange prv 6.5 with a tímpano amp, and a pioneer subwofer active… can i use this DSP?
Yes you can use this DSP for that setup
I have a Taramp amplifier and I believe all taramps are mono amps will that routing work ?
The routing doesn't matter if it's mono or not. You can have one mono amp doing just a left signal and another doing just a right signal using the routing feature!
So how would I do it if I’m only running a 4 channel amp and a mono amp. Can I get away with just the 4 channel dsp or do I have to get the 2x8 dsp.
4 channel dsp would work just fine
@@12voltfever I just wouldn’t have fade control
I got 1 4ch amp but I got ch 1,2 for drivers and ch 3,4 on horns. How you setting that up with the dsp?
Following Also .. im doing ch 1 and 2 for tweeters and ch 3 and 4 for four 6.5 and I need to know how would be done
sorry for the late response, but 1 output of the DSP per channel.
So if I have a 4 channel and I use one Channel for tweeters and one is left other is right do I put it as a and b
Following this comment
Sorry to necro, but hopefully you can answer my question. For inputs, is it only low level, or can it use high-level input as well? I ask cause i syill use an oem player😊 thanks
With just this unit, it is not possible for high level input. However, with an LOC (line out converter( that provides an RCA output, you can certainly use this DSP with your factory radio.
How to use the Limiter feature
For real
I have an active 2 channel LOC. How do I add the Dsp. I also have an epicenter. How would I run everything. Can you please help.
The epicenter would go between the DSP and the amp. The LOC would go to the DSP input
Do you have any experience with the time delay feature?
Yes sorry for the late reply but what would you like to know
What if you got a radio then a pre amp then your dsp ?
I have a video here explaining how to add a pre amp! Check my videos
Hey can you show how to program the dsp .. thanks
Yeah go check my other videos.
Im working on a whole new system using an indash eq with the prv 2.8x dsp and a 5 channel amp (memphis Audio VIVseries Belle) but not using the 5th sub channel (cause i ended up getting a different sub then originally planned cause got a really good deal on sub and the amp). The front channels are running my tweeters the rear channels are the mids. And a mono amp (Memphis Audio VIVseries 2200) to power the VIVseries 14 inch sub. So going to the amps from the dsp channel 1 and 2 go to the front channels (1 and 2) on the amp then channels 3 and 4 go to the rear channels on the amp (3 and 4) then channels 5 and 6 go to the mono amp (5 and 6) is that correct?
Yes that would work
Can you show us how to actually set a dsp?
Every system is different, I do show how to use the crossover in the video
Can any one messege me now need help setting up dsp! Have it running from front rca’s of kenwood ddx26bt and out from prv 2.8 to skar rp150.4 with 4 channels and 2 to taramps 1800.1 d
Any luck yet
Do you have a specific question?
So you can run 1 4ch amp an 1 mono amp. I was correct lol
Its about to go down lol thanks for the vid!!!! 😄😄😄😄
Man I'm doing the same exact thing!! One mono and one 4ch and getting the PRV DSP 2.8 soon here and just wanted to know if you had finished your install and how it worked out for you and a brief rundown of how you did the RCA wiring ..So is it one set of RCA from HU to DSP then with the 4ch amp I combine all the left signals into one output of the DSP and the same for the right ?? And then my sub amps left and right combined into one to go into 1 output of the DSP? Obviously using y connectors to combine Lefts and rights individually into there own one solid RCA to go to DSP outputs. Any help will be much appreciated!! Thank you in advance!
@@mikebugarin3339 i ran 1 set from hu front ch to dsp. 1 y splitter to 2ch rca to mono amp. An then 2 sets of 2ch rca to 4ch amp. Ordered 3ft rca's from Skyhigh
@@mikebugarin3339 set ch1 to A+B signal for mono. Set ch2 to A. Ch3 to B. Ch4 to A. Ch5 to B. But you can pick whatever chan you want to go to whatever amp. 1 - 4 to 4ch amp an Ch5 to mono. It was just easier for me to arrange it that way. I didnt want to uave my rca crisscrossing so i ran my mono outta ch1 an my 4ch amp outta channels 2 - 5
@@mikebugarin3339 you can order certain length rca's from Skyhigh. I just guessed the length i needed. 3ft was more than i needed. Can buy Y splitter as well. Think it was like $28. 1 y splitter an 3 2ch rca's. Price goes up with the length of rca's
So basically it’s only good for people with stunt walls if you’re looking for sound quality keep walking is what I’m getting out of it
That is not true. These are also used on sound quality setups for motorcycle competition