Is your Microwave tripping the breaker?
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- Click Subscribe then read on. 😀
Our microwave started tripping the breaker, so it's time to search for the wiring diagram and dig a little deeper into the problem.
First, locate your model number. It's normally on the inside of the unit. You can find it on the bottom left after opening the door. That model number will allow you to search for the part that I show in the video, but specific to your model of microwave. You can also use this number to find the wiring diagram if you need a temporary-ish repair to avoid the issue of creating a dead short and tripping the breaker every time you pull on the door.
Ideally, after you make this repair, remember to either press STOP before opening the door or wait for the microwave to time out.
Thank you for watching.
Please like and subscribe
💰Donate to Our Channel💰
Zelle: Melonie.Larew@gmail.com
PayPal: Melonie.Larew@gmail.com
Bitcoin: bc1qzjg6wmw97wvhn400gagk8tzqatn82wg4ywq8kl
⭐️READ PINNED COMMENT⭐️
Mission Automotive Dielectric Grease/Silicone Paste amzn.to/3Ndt6JQ
This stuff is SUPER handy and what I ended up using.
Super Lube amzn.to/43WhNNz
#microwave #microwaverepair #diy #repair #appliances
Stop your microwave before opening the door. Problem solved. You are welcome.
You're a pretty fart smeller.... I mean pretty smart feller.
Have a wonderful day!
I never did open the door while it was running . Not even once , but thanks .
Hey, @otgcanada
Yeah, it has less to do with opening the door while it's running and more to do with natural wear of the latch itself and the placement of the monitor switch versus the other 2 switches. Once the latch gets worne a little, just the natural vibration of the microwave can be enough to disconnect the monitor switch during operation causing it to trip the breaker.
Thanks for watching and supporting the channel.
Have a wonderful day!
@@thelarewsdo This oven is brand new , about a week old now . Since I`ve been watching different TH-cam videos after closing the door I`ve been pushing all of the door in slightly and it seems to work . I will be returning it . Thanks for your help .
Good call! That's way to early to be having those issues!
Worked perfectly. Didn't even have to disconnect all the panel wires.
Great to hear! Keep on cookin'
Thanks for watching!
The internet is a great thing! I was saving the same issue and googled “microwave tripping fuse” and found your video. Worked like a charm. Appreciate you putting this out there and the simplicity of your directions. All the best!
Hey Tim!
Thank you! 😀 We are glad we could help you. Thank you for watching and supporting the channel.
Have a wonderful day!
You are THE MAN ! Exactly my problem. Just about to go shopping. Many thanks.
Hey thank you and way to make it happen capt'n! Glad you to hear you are back up and running!
Have a wonderful day and thank you for watching.
oh my word! GOLD! if only I would have started here....I actually thought it was a squirrely GFI breaker bc our washing machine trips it....nope! door switch just like you said!! thanks!!
Hey,
That's great to here! Glad you got it all squared away.
Thank you for watching and don't forget to subscribe to support the channel. 😀
Have a wonderful day!
I have the same problem but my house runs on a 4000 watt pure sine wave inverter . Some thing about the microwave oven that is brand new , that when it starts it trips the inverter . and the entire house goes down . I have cooked entire meals using my air fry toaster oven ( 1800 watts ) , hot plate ( 1000 watts ) , AC on low ( 580 watts ) , fridge ( 120 watts ) , freezer ( 120 watts ) , and the rest of the house that totaled 3375 watts all at the same time with no issues . It is just something about the start on the microwave that causes the inverter to trip and the rated watts for the microwave is only 1350 watts . So... the cure to this was to simply turn the power down on the microwave to 6 instead on 10 and it runs just fine . My oven is a Master Chef . I have even plugged the microwave strait into the inverter with nothing else plugged in and same thing . Hope this helps if you have the same problem .
Hey,
Thanks for the tip!
Have a wonderful day!
I am the worst handy man in the planet but your video makes me a pro 😂. Thank you for saving me $500 I almost bought a new microwave.
Haha that's great to hear! I'm sure your not giving yourself enough credit, but we are glad we could help you!
Thank you for watching and supporting the channel.
Have a wonderful day!
My problem was a bug had crawled under the circuit board and eventually shorted it out on my GE over the oven unit. This is actually the second time it happened on this unit. This time it was cheaper to just buy a new unit rather the whole button/circuit board.
to make sure it does not happen with the new unit I placed some metal screen over the vent area of the circuit board area.
Oh no! Not the typical "bug" you'd expect to find in a circuit. Bet you it won't have the guts to do that again! Kudos for good, Ole fashioned ingenuity. Thanks for watching!
Wow thank you so much. I was about to call an electrician and was worrying about how much I would need to come up with for that. I just followed ur channel for more great tips & fixes. Thanks again 🙏 🥰
Hey Rebecca,
Excellent! Glad to help and thank you for your support. If you have any other suggestions for future videos feel free to email or comment.
Thank you again and have a wonderful day!
Worked exactly as described. Solved the problem. Thanks!
Excellent!
You're welcome!
Thank you for watching and supporting the channel.
Have a wonderful day!
Out of all the vids this is the best one to deal with this situation with a "temp" fix. Exact same issue with the middle switch causing the issue. Works for now but for safety reasons I'll still have to order the replacement of the switch I took out. But thanks for ur vid
Hey!
Thank you for your kind words! I'm glad we were able to get you cookin'. When ordering parts, remember it's the switch holder that gets worn and has play in it. I would also replace the switch since it's been taking a beating. Thank you for watching and have a wonderful day!
I wish I could give this more thumbs up. Easy to understand, to the point, temporarily and permanent solutions. Perfect. Earned a thumbs up and a subscriber
Hey Matt!
Thank you for the support! I'm glad we were able to help you out !
Have a wonderful day! 😊
I found your video AFTER checking the 3 switches and fuse. Your tip saved me a lot of time and money! Thank you for posting.
Hey,
We're glad we could help! Aint nobody got time for a broken microwave. 😁
Good job on the repair.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thank you! I have same problem and was looking into breakers.
Hey Russ,
Welcome welcome. Glad to help!
Have a wonderful day!
Thank you so much i have same issue i saw your video and you safe my time and money.
Please share the link where i have to order the part and please send me the video how to change the part thanks again.
GOD BLESS you
You're welcome. Like, subscribe and click the bell. I'm trying to get a free minute to put together another video showing an improved workaround.
I need 1 more question i need to replace door latch hook or door switch?
If your issue is fixed by unhooking the monitor switch, like in our video, then the next video will show you. We'll be upgrading a switch. But to answer your question, the door latch that holds the three switches is normally what is worn and is causing the monitor switch to malfunction.
@@thelarewsdo i just un plugged bottom one and my microwave was working fine.
Okay sure i am waiting for your new video
Thank you for the video. I had already replaced the breaker thinking it was getting weak.
Great. Glad you were able to get it up and running. Thank you for watching.
Hi have fridgidaire, i have replaced all the door swtiches. Was good for 4 months again same issue. I dont think its the switches its just the door latches. My family aslo does the same thing. I am gonna do what you did and will see.
Hey! Sounds like a plan! If you hooked all the switches back up after replacing them the issue could still be the bracket that holds them. Remember, the wear on the bracket is what causes the monitor switch to close when it's not supposed to and that's what trips the breaker.
Thank you for watching; please like and subscribe to support the channel.
Have a wonderful day!
Worked perfectly for me! Thanks! Do I really need to replace the other two switches now that I am back in business?
I'd say you're g2g if it passes the normal function tests. Good Job!
Thank you for this! Same model microwave doing this. Me and my son pulled it down, unplugged sensor, and now back in business!
Hey Thomas.
Excellent! 👊💥 Glad we could help.
Thank you for watching and have a wonderful day.
Same here , thanks a lot!
You're very welcome.
Have a wonderful day!
@@thelarewsdo you as well, just subbed!
I have this identical microwave and the exact problem you explained about the coffee and I this bypass of the third safety switch worked. Thanks for the video.
Great, you're welcome. 😀
Thanks for watching and supporting the channel.
Have a wonderful day!
On the key pad there is a PAUSE button....that is there for a reason. You do not pause a microwave by opening the door while it is running. Hit pause to STOP the power to the switches THEN open the door and then you don't care which switch opens or closes...there is no power to them AND you don't care where you grab the handle to open it. NO more problems with that middle pad switch getting the contacts burnt.
Hey! Thank you!
I'm sure that 98% of people that view this video realize that. But, over the course of owning a microwave there are extenuating circumstances or "late for work instances" where protocol isn't followed to the 'T'. The summation of these instances is what causes the issue. Life happens.
P.S. Pressing the pause button just opens a set of contacts, under load, that stops the microwave; no different than opening the door.
Have a wonderful day and thank you for watching.
@@thelarewsdo PS...no it don't and why the big Shabelle about following things to a T if it don't matter? Why is pause on the key pad?? I fix them ALL the time and NO ONE uses pause.....or the ones burning the contacts together in that switch don't.
I don't disagree that pressing the pause button would aid in decreasing the particular issue people are having and is good practice. Though, ultimately, by using the microwave daily over many years the latch naturally will continue to wear and the issue with the monitor switch prematurely closing becomes inevitable. I didn't exactly understand what you were getting at with your retort about following protocol to a T, but I think I can answer your question with a question. Why doesn't everyone drive exactly the speed limit or only press the elevator button once...
And relays are simply actuated switches. So yes, when you press the pause button you are dropping out power to the coil on the relay which disconnects power under load from the magnetron, vent fan....
Best wishes. Keep on repairing and be safe.
Kenmore microwave not tripping breaker after fix. However, there is a humming noise when microwave door is closed. Any ideas?
Yep, I'd say one of your other switches is welded in the closed position and can't "shut off" like it's supposed to. They can carefully be taken apart and unstuck assuming they aren't too damaged. Or snag the part # off the side and order you replacements from Amazon or digikey.
Let me know how it goes.
Thanks for watching and supporting the channel.
Have a wonderful day!
So my problem is if i use the microwave for 2 or 3 minutes, stir food, and throw it back it, starting the microwave flips the breaker. You have to let it sit for a minute
Try pressing in on the door the second time you run it after stirring the food. Does it still trip?
Just did it in my Frigidaire and it worked! A real blessing this video man. Thanks so much. I’ll buy the part for it when I can.
Excellent! Glad we could help. We have another video we are trying to get to gether. We are working on a "permanent", cost effective upgrade. The video will be a touch more technical, but the upgrade will cost less the $5.00.
Thanks for watching and supporting the channel.
Have a wonderful day!
This fixed my problem on the exact same model. saved me so much time and money. Thank you so much for making this video. You’re a genius!
Wonderful! Thank you, you are very welcome!
Thank you for watching and supporting the channel.
Have a wonderful day!
I bought a microwave yesterday this morning when making coffee I noticed the clock changed. It went from 8:03 to 20:03.
Hey Andrea!
That should be a setting in the menu. Look for 12/24 hr. You'll want to select 12hr. The menu instructions should be behind the door on the microwave. You should see it on the perimeter of the frame once you open the door. Hope this helps.
Thanks for watching and supporting the channel.
Have a wonderful day.
Thank you my granddaughter needed help it was a Frigidare
Happy to help! Thank you for watching and supporting our channel. Have a wonderful day!
I have a Frigidaire Gallery FGM17WNVF(A). Power went out on the microwave so, nothing worked, no lights, not anything. The breaker did not trip so I checked the fuse first and found that it still had continuity but, I replaced the fuse anyway. Still no power. Could this still be the monitor(3rd safety) switch and if I do disconnect this switch, does the capacitor need to be discharged? I ask because with the front panel off, I’m not seeing a capacitor. Appreciate any info.
It does not seem likely that it's the monitor switch. Have you confirmed that there is power on the outlet that supplies power to the microwave?
@@thelarewsdo yes, I plugged a lamp into the outlet and it still works.
Ok, good deal. My next step, since you've checked the fuse, would be to check the thermal cut-outs. They are circular with two tabs with screw holes and two terminals on the bottom. Check them for continuity. If one of them would be bad that would cut the power before it makes it to your control board.
Let us know how it goes.
Thank you for watching and supporting the channel.
Have a wonderful day!
Worked perfectly. Thanks
Excellent! Glad to help!
Thank you for watching and supporting the channel.
Have a wonderful day!
Thanks a bunch!!! Solved my problem
Excellent! 👊 Good job!
Thanks for watching and supporting the channel.
Have a wonderful day!
How essential is it to replace to the monitor switch ? I disconnected it and micro wave works just fine.
Hey Mike,
Our is still unhooked. 😉 I have a new video to make to show a quick fix that I'm working on that will put all the safeties back without the hassle .
Thanks for watching and supporting the channel.
Have a wonderful day!
Yes! If I have the microwave and air fryer on at once the breaker gets tripped and shuts everything off in the kitchen! Also,I hear popping and crackling from the breaker box when the microwave is on.🙄🙄😞😞
Hey,
The breaker is getting overloaded. Your kitchen breaker is probably a 20 amp breaker. The microwave pulls ~12 amps and the air frier pulls ~12 amps so combined your are at 24+ amps; That's why it's tripping. You may want to check if the outlets on your counter are on different breakers and move your air frier to a different location. The popping and cracking in the breaker box means the screw holding the wire into the breaker is loose and needs tightened; this needs addressed asap. The popping and cracking is arcing which can lead to a fire. It's a super easy fix, BUT requires knowledge of electricity to safely fix it.
Hope this helps answer your questions. Thank you for watching.
This happened to me last night
@@thelarewsdoSomething that I always thought about is to install one 30amp circuit in the Kitchen with 20amp outlets with 10/2 wire and two 20amp circuits with 12/2 wire in the kitchen!! Then you will have plenty of electricity!!
Hey Dimitri,
Interesting idea, but I have a few thoughts.
10 gauge wire is a bear to work with as far as bending and "squishing" into single outlet boxes. Plus, I'm not to sure that most 15/20 amp outlets are designed to adequately secure 10 gauge wire behind the terminals. If you breaker panel is large enough, one thought would be to home run each of your kitchen outlets with 12 gauge wire. This will give you 20 amps available at each outlet, it isolates the appliances and the wire is easier to work with.
Hope this helps. Have a wonderful day and thank you for watching.
@@thelarewsdo Ok thank you.
Thank you so much, this worked for me, and I have the exact same brand 😊
Excellent!! Glad we could help.
Thank you for watching and be sure to subscribe.
Have a wonderful day!
This fixed my issue!! I replaced the breaker thinking it was weak... then replaced the 20A fuse in the microwave... then found this video! thumbs up'd and subscribed to ya!
Hey Maple Man Dan!
Excellent! Glad we could help ya! Thank you for watching and supporting the channel.
Have a wonderful day!
my problem is when i close the door the display and power goes out, and if i hit it harder or close the door again it comes back on again
Hey!
Sounds like a loose connection on your control board. Unplug the microwave and access the panel, as shown in the video. Then carefully unplug and plug back in each connector.
Good luck!
Thanks for watching and supporting the channel.
Have a wonderful day!
@@thelarewsdo thanks
Problem solved
Thanks sir
You are very welcome! Glad we could help.
Thanks for watching and supporting the channel.
Have a wonderful day!
Thanks so much. It actually worked for me. Ordered the new parts too
Hey Theodore!
That's great to hear. 👊💥 Glad we could help you out.
Thank you for watching and have a wonderful day!
It worked on my GE! Thanks! 👍
👊💥 Glad to help.
Thank you for watching and supporting the channel.
Have a wonderful day!
Worked great! Thanks for the help!
Excellent! Glad to help!
Thank you for watching and supporting the channel!
Have a wonderful day!
ima silicone grease that betty
Absolutely! An ounce of prevention is worth a pound of cure.
Thank you for watching and supporting the channel.
Have a wonderful day!
It worked. Thank you
You're welcome.
Thank you for watching and supporting the channel.
Have a wonderful day!
This same thing was happening to our microwave and we had to train ourselves to stop it before pulling the door open to prevent it from happening. Now the microwave trips the breaker just being plugged in. Could this still be the issue or would it be something else now?
Hey! Yes, from the sounds of things I'd say that the tips on the switches finally fused together. Assuming it's only the monitor that fused, unhooking it should fix it. Let me know how it goes and remember, UNPLUG it and let it sit a while before digging into it.
Thanks for watching and supporting the channel.
Have a wonderful day!
It worked! Thank you so much!!
@@CoCBlazin Which switch did you unhooked, the top or the bottom?
My Whirlpool WMH76719CS trips breaker when I press START
👊 💥 Excellent!
Sounds like one of the switches is stuck so they'll need carefully taken apart. Check through the comments, there's a couple different places I've explained the process. Thanks for watching and supporting the channel. Have a wonderful day!
Great info
U got my working again 😊
So glad it helped! Thanks for watching and have a great day!
Thanks for the video, saved me money
You're very welcome! Glad we could help.
Thank you for watching and supporting the channel.
Have a wonderful day!
Worked for me ty
Hey Joel,
Glad that was able to get you going!
Have a wonderful day!
My Frigidaire trips the breaker soon as I press start. Do you think it’s the same issue?
Sounds plausible that the switches are the culprit.
That would be a good place to start. They can be tested individually with a multimeter to rule them out.
It's the switches. If I just close the door and press start it trips the breaker. If I firmly close the door and simultaneously continue to apply pressure to the door and press start it never trips the breaker.
Great video, much appreciated. Question. Your saying that your circuit breaker gets popped when this issue happens. Wouldn't the fuse blow first? I have went through 5 fuses in last 8 months and I finally (duh) decided to dig into the root cause. I saw your video and just replaced all three door switches. Fingers crossed. If it happens again, I will disconnect the monitor switch as you suggested. If that doesn't do.......I'm done! LOL. Thanks again for your video help.
Hey,
You're welcome and thank you!
The fuse is protecting the control circuit, but the monitor issue is on the power side; That's why it blows the breaker.
Let me know how it goes.
Thank you for watching and supporting the channel
Have a wonderful day!
@@thelarewsdo Hi again. Well dangit!! After 10 days the fuse blew again. Do you think by unpluging the monitor switch (which was popping your circuit breaker) this might finally solve my fuse blowing issue? Many thanks again!
Hey,
At this point, you wouldn't be out of anything to give it a try. What style and amperage of fuse are you using? (slow blow or fast blow style fuse)
@@thelarewsdo I'm not sure what the fuse type is called. It's a 20Amp glass with a solid metal strip.
@@thelarewsdo Ok, I unplugged the monitor switch. Fingers crossed, wish me luck...
amaizen
Thank you.
Thank you for watching and supporting the channel.
Have a wonderful day!
We did replace it and still tripping
Hey,
Check through some of the other comments and you should find some help.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thank you very much. It worked but now the issue is whenever I am opening the door the fan starts running. I am afraid that is it just a fan or it starts cooking even when the door is open. Please provide your input asap.
Hey,
Check back through previous comments, this is kind of a common issue also. I'd say one of your other switches is welded together and is stuck in the "on" position.
The switches can be carefully split apart and unwelded, assuming they're not too damaged, or they can be replaced by purchasing them on Amazon or digi key.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thanks for your quick reply, but I am not able to identify other switches. Can you please help me to locate that switches.
In the video around the 3:05 min. mark I mention interlock switches. Those are the other two of the 3 switches.
@thelarewsdo love you, man. It worked. You made my day and saved $.
I did that & messed up my door
Hmmm, you did something, but it wasn't "that" if it messed up your door. If you were having the breaker tripping issue, it's a matter of discounting one plug. I'm not sure what you would have changed to affect your door. Reverse your steps and see if that resolves your issue.
Thank you for watching and have a wonderful day!
Bless you for making this video. I couldn’t figure out why my microwave kept tripping my breaker. This video helped me solve the problem.
Thank you and that's wonderful to hear!
Thanks for watching and supporting the channel.
Have a wonderful day!
May GOD Bless you brother…. You just saved me $200+
Your video just fixed my microwave…once again, GOD BLESS YOU
Thank you 😀
I'm glad we were able to help you out!
Thanks for watching and supporting the channel.
Have a wonderful day!
Good video
Thank you!
Hope it helps.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thanks so much!!! I just fix my Frigidaire by myself 😊!! It’s working now perfect 👍🏼
Hey!
You're very welcome! Good job.
Thank you for watching and supporting the channel.
Have a wonderful day!
If you hit the shut off button and do not open the door while power is on, that works too, but it's a hard thing to remember, we as so used to pulling the door open.. and we are blowing the fuse every time, too bad my TV box is on the same circuit, takes forever to reboot that Comcast Box..
Lol yep. Life happens and we get in hurry sometimes.
Thanks for watching and supporting the channel.
Have a wonderful day!
Thank you so much for your video. I reset the clock on my microwave yesterday after a power outage which is option 3. My microwave only has four options by the way and to turn off the display mode on mine it's option 4.
I waited for it off to display and pressed the start button and now my microwave is working properly again after turning off after 3 seconds for some mysterious reason.
I cannot recommend this Frigidaire microwave because of this convoluted option system for changing settings. The manual gives completely wrong instructions on how to operate it or even do something simple like changing the time. I appreciate your video
You're welcome.
Thank you for watching.
Have a wonderful day!
Thankyou.
You're welcome!
Thank you for watching and supporting the channel.
Have a wonderful day!
hi, first thanks for the video, it is really helpful. i've a Frigidaire and your solution almost worked. In my case the fuse was blowing up when the microwave was plugged-in and when i disconnected the monitor switch, it stopped blowing-up however when i open the door, the plate rotates. Any ideas around that? Thanks in advance.
Hello, you're welcome. I would have to look at the specific wiring diagram for your unit to be sure. When your monitor wire was hooked up did it only blow the breaker when you pulled the door open while it was running or did it do it all the time?
Hey thanks for the video. I have exact microwave. I removed the second switch because the button wasnt clicking. I pryed the plastic cover off to have a look and somehow it started clicking again. Put cover on and its been just fine. I ordered the 3 switches for 13 bucks just to have incase it starts happening again.
Hey,
Great to hear! Yeah, the contact tips on the switch melt together due to the arcing cause by the short. Remember the problem is caused by the slack in the latch that activates the switches out of sync.
Have a wonderful day. Thanks for watching and supporting the channel.
Did not show how to install Door Latch Hook.
I love you 😘
Haha thanks 🤣 Was it the flannel or can I assume your microwave lives again?
Have a wonderful day!
Thanks for the great video! I came home from work late tonight and at 11:45 pm found out the microwave was tripping the breaker, but thanks to your video I was able to “fix” it by removing the monitor switch. Now my wife has the microwave to use tomorrow to help get the kids ready for school.
Hey,
You're welcome. I'm glad to hear we were able to take some stress off of you. 😀
Thanks for watching and supporting the channel.
Have a wonderful day!
Thank you Sir! Mine Eventually would shut off and trip breaker the second I hit start. Thank you!
You're welcome. Once the hooks on the door start wearing the latch down those issues start occurring. I'm glad you were able to get back up and running. A new latch (the piece that holds the switches) will be the ultimate fix.
Thank you for watching and supporting the channel.
Have a wonderful day!
Sorry I didn’t understand one part. So when we disconnect the bottoms switch. Do we leave that one disconnected and reconnect everything else after? Or disconnect and reconnect? Great video by the way, been struggling with this microwave.
Hey! No worries. I disconnected the monitor switch (it's not the bottom one in my microwave; its the 2nd of the 3) and left it disconnected and everything else gets hooked back up.
Hope this helps.
Thank you for watching and supporting the channel.
Have a wonderful day!
Finally decided to try and fix mine after years lol. I’ve been using a spare and recently bought a new smaller one which is entirely too small. Finally figured out the right switch to unhook and boom it works. Thanks so much
Excellent 👊 💥 You're welcome! Glad we could help you out!
Thank you for watching and supporting the channel.
Have a wonderful day!
Worked on my GE. You just saved me over two hundred dollars.Thank you!
Excellent! You're very welcome!
Thank you for watching and supporting the channel.
Have a wonderful day!
Same exact thing on a general electric microwave. Thank you!
Hi Andrew Fisher!
Excellent! You're very welcome!
Have a wonderful day!
Wow! Worked like a charm.Thank you so much. You are amazing🙏🏻
Hey! Thank you!! Good job fixing it.
Thank you for watching and supporting the channel!
Have a wonderful weekend.
Sending my appreciation all the way from the Yukon. Thank you so much!
Fred! You're very welcome, we're glad we could help you! The Yukon looks beautiful from the pictures I've seen.
Thanks for watching and supporting the channel.
Have a wonderful day!
Thanks! I just did your steps and voila! A working microwave!
Welcome, welcome 😀
Glad it helped and have a wonderful day.
Please like and subscribe to help support the channel.
Thank you! It worked ❤
That's great to hear! You're welcome.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thank you! That just saved me $350 and several hours of my weekend!
You're welcome 😀
Glad we could help! Enjoy your weekend and have a wonderful day!
Exact problem on my GE, meanwhile it’s same hooks assembly. Thanks!
Hey Vladimir,
Good deal. Glad you were able to get it figured out.
Thank you for watching and remember to like and subscribe to support the channel.
Yo, just did this right now to my moms microwave. Works like a peach. Thank you so much 😊
Haha you're the favorite kid now ! Any time.
Thank you for watching and supporting the channel.
Have a wonderful day!
#BOOM! I also didn't disconnect the wire harnesses - just the lower switch. Back in business!!!
Excellent! Glad you are up and running.
Thank you for watching and supporting the channel.
Have a wonderful day!
It worked! Amazing
Hey!
Great, now your cookin' lol.
Thanks for watching and supporting the channel.
Have a wonderful day!
Thank you for sharing this information. It worked and saved me $$$!
Hey Barb!
You're very welcome! We are hoping to add a follow-up video. If all goes well, it should improve upon the microwave's design, use all the safeties, cost less than $10, and be just as easy as the previous fix to implement.
Thank you for watching and supporting the channel.
Have a wonderful day!
Worked Perfectly! Thanks 🙏🏾 💪🏾
You're very welcome! Glad we could help.
I attempted this on my Kenmore and now my microwave constantly runs when turned on and no way to shut it off other than opening the door.
Hey,
Pressing the stop button doesn't stop it?
This is a response I sent to another individual, it may help.
"It sounds like the tips of the switches talked about in the video are melted together. Test the three switches by pressing the little white buttons that stick out of the sides of them. ( make sure your microwave is unplugged ofcourse) If the button doesn't click that's your culprit. You can remove the problem switches one by one and open/split the sides to see the internals. Next, use a small screwdriver and carefully pop the tips back apart then reinstall them.
Hope this helps."
Thanks for watching and supporting the channel.
Have a wonderful day!
Thanks for this video. Quick save before Thanksgiving.
Hey Scott!
You're welcome. Glad to help!
We hope you and your family have a wonderful Thanksgiving 🦃.
Thank you for watching; please like and subscribe.
And nobody comes with the idea that if one of the switches have a malfunction the micro wave oven give an error code just like an modern air condition unit
I agree, there's a lot of things that could and should be upgraded relatively easily to make a more solid unit. But... can you imagine how many microwaves they have sold as replacements because of that simple malfunction? Lol 🤑
Good job for taking a malfunctioning microwave a step further and looking for a solution! Sometimes a $2.00 part is all it takes.
Thank you for watching and supporting the channel!
Have a wonderful day!
Perfect!!! This was the fix I needed to save hundreds if dollars!!
Wonderful! Glad we could help!
Thanks for watching and supporting the channel.
Have a wonderful day!
soooo until i buy my parts. im just gonna hit stop before opening the door! TY for the video boss😊🎉
Haha 💯! Yeah as long as you fight the urge to touch that door before the light goes out you're g2g. 💡💥😑
Thank you for watching and supporting the channel.
Have a wonderful day!
Now how to put the pieces back 😮
Hey,
I'm not sure what pieces you are referring to. There weren't any pieces permanently removed in this video. All that needed temporarily removed was a few screws and a panel to get to the monitor switch then just do everything in reverse to put it back together. Is there any chance you have your repair videos confused?
The hook/spring on top of the door inside now it won’t go up or down
Can I keep that temporary solution permanent lol? Or do I have to replace that part?
Hey!
I'll say this much, ours has been working wonderfully with the temporary setup since I fixed it. We hope 🤞 to have a new video soon showing how to make it 110% better than factory with a simple part.
Stay tuned.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thank you sir. It worked for me. If I just leave it like that without buying a new one is that going to cause me some kind of electrical problem?
Hey,
You're welcome! Since that is one of 3 safeties, you should be fine; there are still two safeties still in the circuit. Now, if you were wanting to put it back to 100%, remember it's not the switch that is causing the real issue. The wear on the latch is what is causing the switch to activate when it shouldn't, so you'd have to replace the latch.
Thank you for watching! Remember to like and subscribe.
Have a wonderful day!
Thank you very much buddy I appreciate you. Will do. Have a great weekend
Any time. Have a great weekend as well.
How does the latch contact 3 switches with 2 hooks?
Hey,
The two " points" of the hooks actuate one switch each and the round part of the bottom hook (I think it was the bottom) also press in on the third. That's the one that has the issues. Once there is alittle play in the door latch the monitor switch can change state before the other two. Hope that makes sense. Watch the video again and you should be abile to see it, now that you know what to look for.
Thanks for watching and supporting the channel.
Have a wonderful day.
@@thelarewsdo Got it ! I have no problem with the switched ( I dont think) as the latch spring holder broke off, Of course they dont make them anymore, but I found one that has the same dimension and am waiting for it to arrive. While I have it apart I held the latch with door open and pressed down on the top and bottom switch and fuse blew. I knew that it had to do something with the middle switch mounted near the bottom but I did not pull out plastic piece that holds switches and could not see how the middle switch was activated.
I had a latch spring holder break on a previous microwave and I drilled a new hole to hold the spring. There is much less room to drill to hook a spring on with this latch.
the GE latch I found was placed on a one inch square graph paper to show dimensions and I made same grid paper and everything matched up.
With my luck it will be slightly off.. worth a try for $9.00. Luckily I keep a spare microwave in attic for times like these.
I paid a fortune for this and it is 3 months past warranty.
If it comes down to it I can print a 3d copy or make a mold.
Im the typr of person who will try and make things work by making my own parts. I remember using rubber bands for my VCR when they no longer made belts for it.
Haha 💯. Necessity is the mother of invention.
You are the man! Thank you for posting this and saving us $$$$$
You're welcome and thank you!
Thanks for watching and supporting the channel.
Have a wonderful day!
Thanks for putting me on the right track, the core problem is most likely yanking the door open while the microwave is running, the 2 safety contacts can’t handle and are not designed to take that kind of arcing.
Hey,
Glad to help!
Thanks for watching and supporting the channel.
Have a wonderful day!
Explained perfectly and I now have a working microwave!
Hey,
Thank you! I'm glad the video helped!
Have a wonderful day!
Thank you so much. You are a genius. How the hell did you figure that out.
My unit is built in more than most. So a big job to change.
Hey,
Thank you for your kind words! I'm happy to hear we were able to help you. 😊 Good job on working to find a solution!
Have a wonderful day!
I love TH-cam!!! Thanks for the help brother 🤝🏽
Anytime 👊💥! Glad we were able to help you out!
Thanks for watching and supporting the channel.
Have a wonderful day!
Thank you so much! Exactly what was wrong with mine. 👍. Just earned a follow as well!
Hey Shannon!
That's great to hear x 2! Thank you and have a wonderful day!
All my microwaves do this including my new Kenmore ticks me right off
Yeah, it's kind of a silly feature. I am working on a fix and will try to have a video in the not so distant future.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thanks for saving me $300 worked like a charm.
Excellent! Glad to help!
Have a wonderful day!
Please like and subscribe to support the channel.
Bless you! Possibly the quickest and easist fix of an appliance ever!
Hey Ronald!
Thank you. Glad we could help you out.
Thank you for watching and supporting the channel.
Have a wonderful day!
Thank you so much sir! You have saved us from purchasing another microwave.
You're very welcome! We're happy to help.
Have a wonderful day and thank you for watching and supporting the channel.
Thanks!!! Just saved me a new microwave.
Welcome 😀
Thank you for watching and supporting the channel.
Have a wonderful day!
It worked! Thank you for this video!
Excellent! You're very welcome!
Thanks for watching and supporting the channel!
Have a wonderful day!
Thanks buddy! Just went in and took the plug out without any only and was done!
👊 💥 You're welcome! Glad you're back cookin'.
Thanks for watching and supporting the channel.
Have a wonderful day!