Awesome video - short, to the point, and it shows all of what's involved. Seems very well done and efficient!! Going to reach out as I need some help with a windshield. Thanks for the info and engagement in the comment sections - very helpful.
I Had my windshield replaced in my 2019 Tacoma crewcab sr5. Does it make a difference if the installer didnt take out the plastic piece are the bottom of the windshield? Also the plastic piece that is on the outer part of the windshield. It lays flat but it looks like it has a bubble in it. I just had it installed today. Will the heat make it go down over time?
Yes that is a poor installation. They should have removed that in order to set the windshield correctly without rolling or sliding the urethane down. When they do this it can warp the cowling. But sometimes they just get warped from being in the sun. So a little bubble or more like a bow where it isn’t touching the windshield isn’t the end of the world. What’s also more important is that they used primer and covered any of there scratch marks. Take a flash light and look around the frame of the windshield. Use a tiny pick to lift the rubber on the top to see if they left bare metal or covered the scratches up.
@@TexasGlassToolsLLC currently it is raining, but the last part in your video. When the re-calibated the windshield. Did they have to do this? I just want my truck to be back to OEM standards. I read online this is something that is need.
@@TexasGlassToolsLLC I watched them install the windshield. Before they put it. He used a brush around the outer area were the windshield was going to be place...
@@TexasGlassToolsLLC before they put in the windshield they pull the windshield and all of the old material. Use the gun with the black material and installed the new windshield. Plug everything back in that was unplugged from the inside. Do I have to re-calibated my truck?
They have to use special software to recalibrate the windshield with the computer in the car, otherwise systems like lane departure warning, adaptive cruise control, etc. will not work right.
@@popclutch_100 If for example your lane departure waning is beeping even when you're driving straight, or your adaptive cruise control is malfunctioning, the car should tell you that things are off.
No you have 4 inches to play with. If it’s been lifted beyond that I would reccomend just leaving the system as is not recalibration and then turn it off and do not rely on it.
@@Russianmafia10 where are you located? I can find someone to do it for you. They just don’t know what they are talking about. 1 inch in tire isn’t gonna be doing much
@@TexasGlassToolsLLC I'm in Massachusetts. It's a catch 22 because the dealer said to change it and not calibrate and they would finess the cards and make it pass if I get any errors, but need someone to do the glass. But most places won't touch the glass if they won't calibrate it. I think I just found a shop that will do only the glass so I might have a chance
Awesome video - short, to the point, and it shows all of what's involved. Seems very well done and efficient!! Going to reach out as I need some help with a windshield. Thanks for the info and engagement in the comment sections - very helpful.
Thank you Man!
Will having the windshield re-calibrated effect the tune on my tacoma?
No it will now
How much did yall charge for calibration
That's a nice target stand!! Interesting setting tool as well. Thanks for sharing 👍🤙😎
Yes it is!! Send me a email if you are interested! I offer financing as well.
Great video . One question what happens if you don’t calibrate the windshield ?
It can be off and not correctly read the lines.
is there a way to install a new windshield without recalibrating it like not disconecting none of thr harness
No every windshield with a camera must be recalibrated. It doesn’t matter if you unplug it or not that has nothing to do with it.
I Had my windshield replaced in my 2019 Tacoma crewcab sr5. Does it make a difference if the installer didnt take out the plastic piece are the bottom of the windshield? Also the plastic piece that is on the outer part of the windshield. It lays flat but it looks like it has a bubble in it. I just had it installed today. Will the heat make it go down over time?
Yes that is a poor installation. They should have removed that in order to set the windshield correctly without rolling or sliding the urethane down. When they do this it can warp the cowling. But sometimes they just get warped from being in the sun. So a little bubble or more like a bow where it isn’t touching the windshield isn’t the end of the world.
What’s also more important is that they used primer and covered any of there scratch marks. Take a flash light and look around the frame of the windshield. Use a tiny pick to lift the rubber on the top to see if they left bare metal or covered the scratches up.
@@TexasGlassToolsLLC currently it is raining, but the last part in your video. When the re-calibated the windshield. Did they have to do this? I just want my truck to be back to OEM standards. I read online this is something that is need.
@@TexasGlassToolsLLC I watched them install the windshield. Before they put it. He used a brush around the outer area were the windshield was going to be place...
@@popclutch_100 did they actually put black primer over the scratches?
@@TexasGlassToolsLLC before they put in the windshield they pull the windshield and all of the old material. Use the gun with the black material and installed the new windshield. Plug everything back in that was unplugged from the inside. Do I have to re-calibated my truck?
My men , what’s the name of this song in the cámara
What was the last part to the video for btw?
They have to use special software to recalibrate the windshield with the computer in the car, otherwise systems like lane departure warning, adaptive cruise control, etc. will not work right.
@@karkule5919 I had my windshield replaced in the company told me reset itself. I was told this isnt true.
@@popclutch_100 Maybe you don't have to, not sure.
@@karkule5919 how can I find out
@@popclutch_100 If for example your lane departure waning is beeping even when you're driving straight, or your adaptive cruise control is malfunctioning, the car should tell you that things are off.
where are you guys located?
Near San Antonio Texas
If the truck is lifted, can you just raise the cards to make the system calibrate
No you have 4 inches to play with. If it’s been lifted beyond that I would reccomend just leaving the system as is not recalibration and then turn it off and do not rely on it.
@@TexasGlassToolsLLC jeez, I have a 1 inch lift from the tire size on my truck and every place refuses to calibrate it cuz they say it'll fail....
@@Russianmafia10 where are you located? I can find someone to do it for you. They just don’t know what they are talking about. 1 inch in tire isn’t gonna be doing much
@@TexasGlassToolsLLC I'm in Massachusetts. It's a catch 22 because the dealer said to change it and not calibrate and they would finess the cards and make it pass if I get any errors, but need someone to do the glass. But most places won't touch the glass if they won't calibrate it. I think I just found a shop that will do only the glass so I might have a chance
@@Russianmafia10 what city are you in. If you look me up you can get my info. I can get you a contact
Good job!
Thank you! Cheers!
nice job brotha.
Thank you!!
Nicely Done!!
Thank you!
Great work
Thank you so much 😀
Top set it, too many connections points, no van markings , seems like a whack operation with someone just trying to make couple bucks
dam why you wasting time taking off the cowl lmao
lol! We know you do too!
@@TexasGlassToolsLLC😂😂😂🎉🎉 very true