Sub-Zero Freezer Door Seal

This video is about Sub-Zero freezer door seal

[@lgoler]

I did this job without taking the door off. Stupid me. Made it much more difficult to do but not impossible. The bottom being most cumbersome to access. Also, I took off the metal completely, seated it in the gasket and then put back together. Your way looks much easier. If I find my freezer isn't getting back to zero, you can bet I'll be taking the freezer door off:). Thanks for a great video.

[@cpzephyr]

THANK YOU! This was awesome instructions and saved us an expensive service call!

[@garymartin2657]

First thing is how to get the freezer drawer out of the unit !! Remove ice tray and foods of course then remove the top basket, then bottom basket---then support the drawer front on the floor and remove 3 each 1/8" allen-head screws each side at end of drawer slides=back of drawer. (Turn off ice-maker and drawer-open alert before doing above).
Drawer then weighs only 15 lb or so, easy to handle. I followed the video and would recommend the following, so you don't pull out all your hair: soaking not necessary. The hex-head screws will not come out, but be sure to loosen each screw to its max as you will see the gap increase from the screw to the retainer plate. After old gasket removed, clean all surfaces between retainers and drawer chassis, THEN use a normal putty knife to lift the retainer plates up onto the screw threads so you get the max distance you can to insert the lip of the new gasket….!
Go all the way around the drawer. This would avoid prodding and poking the gasket to try and get it placed (potentially rupturing the gasket). As soon as you get several inches of gasket properly placed, lightly tighten screws and move on, just like video. I found my putty knife worked a treat getting gasket lip under plate--better than a screwdriver. End.

[@mrbiznessguy]

does this mean that the fridge will still be running but the freezer won't be running because it thinks its open? Will this mess up the fridge while I change the gasket? How long do I have?

[@JoePantanella]

Thanks you just saved me 265$ they wanted 350$ to replace it!

[@elinewsom9313]

Thank you sir!

[@yammyhaw]

Great video on how to do this...it helped a lot! But I wish I'd read the comments beforehand on what to buy or not buy. I ordered what I thought was an OEM part (but it did say replacement & was made in Canada). It did not seal properly or create a vacuum like my old (original) one after installation. Of course, I could not return it. Contacted SubZero and they were very helpful sending me to an authorized parts dealer that "is" OEM. Cost $20 more but just ordered it...will see.

[@Mayhemsr1]

Who sold you the seal for $20

[@SubZeroSpecialists]

Soaking the door seal in hot water softens the material and allows stretching instead of tearing, also allows the seal to restore its original shape.

[@chiefchero6198]

If you'll allow me to point a few things out good sir. You don't have to soak the gasket for the freezer drawer. I know the instructions say to do so, but that only applies to the larger ones that come folded in a box. This gasket does not come folded in the box so no need for a heat gun/hot water. Also, it's is actually MUCH easier to take the retainers off completely. You can fit them into the gasket much easier when it's off. One last thing that I didn't see you do, some food safe silicone around the corners of the gasket, where in makes contact with the door, will prevent whistling when you shut the drawer.

[@monatheformerferalcat]

This was helpful - which side of gasket do you put silicon?
between door and gasket or other side of gasket where it meets freezer

[@chiefchero6198]

@@monatheformerferalcat along the corners where the gasket meets the door. I’d say about 4-6 inches in each direction is sufficient. Doesn’t take much. A simple bead along the white plastic door liner will do. Otherwise, when you tighten the screws, a bunch will squish out of the edges.

[@Channel-jj9zw]

This is so helpful. Thank you doing this video.

[@SubZeroSpecialists]

If the door seal is installed correctly you won't need silicone. Many of my customers expect the door to whistle when closing as a confirmation that freezer is working properly, but adding silicone won't hurt.

[@Twigglesnix]

this is a super helpful video. Thank you so much!!!

[@WilliamSmith-hq2hr]

Thank you for your great instructions. I bought an aftermarket part and it installed perfectly on my 650 freezer drawer. I didn’t use silicone. The gasket magnets seem very weak and the drawer is easy to open. The freezer hasn’t been able to get to 0 degrees. After a few hours, it’s at 8. When I close the drawer, I don’t hear the vacuum like sound I used to hear. Doesn’t seem to seal nearly as well as the old worn out gasket. Should I try a better part or is there something else I can try? Thanks for your help.

[@SubZeroSpecialists]

You don't have to soak the gasket in hot water, it just makes it easier to put on.

[@SubZeroSpecialists]

I wouldn't use an aftermarket gasket because they're not made as well as the factory.

[@SubZeroSpecialists]

I wouldn't recommend an aftermarket door seal. You can get the exact replacement part from an authorized parts distributor. I use Northeast Certified Parts 800-542-2313. You'll need a 1/4" hex head driver to loosen the screws. Starting at the top is my preferred process.

[@leeackermann3458]

Is it possible to replace the freezer drawer seal with out removing it? Thank you so much for the videos. I think you just saved me $500

[@SubZeroSpecialists]

If the door is all stainless you cannot take it apart. If it’s a stainless panel you can slide it out.

[@SubZeroSpecialists]

The freezer door seal must be air tight or you will get condensation or frost buildup. Check around the whole perimeter of the door with a dollar bill, there should be drag, if not then the seal isn’t sealing and you may need to adjust the door hinges. Look up our tech-help files on subzerospecialists.com, there should be some instructions on how to align the doors.

[@bkking5625]

Do you have an aftermarket for gaskets? I have a 561 and unable to locate a replacement part. Also looked at this door and has socket head on the steel plate that holds the gasket in place. Soaking seems like it'll make it easier. Since I don't plan to remove the door (Freezer) I would imagine start on top down.

[@chauncymax]

BK King I would check Great Plains . They carry oem parts for older models.

[@chauncymax]

ci3.googleusercontent.com/proxy/DpljMe7vXyXWyA0Mc0kTjN9Q_JgyxTsSb1tI5Ux_07YDekuhvBArB0RYGxrpBLl1b6jLUqydJuFm29PNEwpsTdAtuCQ9n4TN5jNU9RpUnSkbaW68dQ=s0-d-e1-ft#greatplainsapplianceparts.com/distributor/email/header.jpg

[@SubZeroSpecialists]

You are always better off using the parts from the manufacturer they’re better quality. As for the freezer not being cold enough I doubt if it’s the seal unless you have a wide gap somewhere. Make sure the condenser is clean and set at 0 degrees, also check the freezer for ice accumulation and fan operation.

[@WilliamSmith-hq2hr]

Thanks for your reply. Turned out I wasn’t patient enough. Subzero says to wait 24 hours after any kind of repair. The freezer reached 0 overnight and has remained there, even after I replaced the fridge gasket and cleaned the condenser, although I had the unit off for a couple hours during that time. Everything is good. I’m back to dealing with a leaking condensate trough at the back of the refrigerator. Drain is clear, but the condensate leaks through the back of the trough and through the screw holes and around the screw heads. Ice forms. This has been a big problem. The new fridge gasket seals well, and it was part of the problem. But I still have this to deal with. Going to try a food grade, waterproof caulk on the trough. Not sure what else to do.

[@SubZeroSpecialists]

You can only buy genuine SZ parts from an authorized dealer.

[@casimirwierzynski7478]

Hello! Thank you for the very useful video. Do you use Sub-Zero branded replacement gaskets or have you had luck with after-market parts?

[@VickyGeagan]

Do not use the cheap aftermarket parts their counterfeit and do not have the magnets in the gaskets so they will not seal properly. I replaced the gaskets for my sub zero 650 f with aftermarket ones and they did not work properly and leaked. I ordered replacements directly from sub zero's parts manufacturer their website is here www.refrigeratorpartreplacements.com/ they have all their replacement parts expect for their door panel they can be custom manufactured through interstate plastics made to size just have your panel size ready when you order and order the them in the abs plastic I had to replace my freezer drawer panel and it worked out great also real easy to clean. the only kind that will not make is the stainless steel I used the abs extruded plastic can not even tell that is is not the original hope this helps anyone.

[@SubZeroSpecialists]

This video is on how to replace a freezer door seal. We have other videos showing how to remove the door or you can peruse the Tech Help files on our website. www.subzerospecialists.com

[@SubZeroSpecialists]

You must remove the door by pulling it straight out until it stops and then lift it off the tracks.

[@enizzle7]

Sub Zero Specialists
On a 650s model ... can you take the seal off and dismantle to access the stainless steal? Wondering if I can push a ding m/dent out (such as you would a car ding via paintless door ding removal)

[@wetphoto]

The manufacturer's instructions say to place a thin bead of silicone on the door before placing the new gasket. Is this necessary? I don't see you mention this procedure on this video

[@chiefchero6198]

If you don't use silicone at least around the corners, it may whistle when you close the drawer.

[@moviebizman]

Thank you. I have a 632 model with a vertical freezer. How important is it that I soak the new one in hot water. Will I be able to work with it if I don't? Thanks.

[@dougiverson4297]

My sub zero 550 is not making ice well. I pretty much have to do the jumping across the terminals to make it wake up or work. I replaced the unit and the water pump. I am worried it is the condenser but I am going to try this door seal next.
it seems that perhaps the top part of the fridge is not cold enough to activate the ice removal cycle. The door seal is damaged like the one in the video.
Is it possible it is the door seal that is preventing the ice maker cycling. The temp control is at 4.

[@SubZeroSpecialists]

Check the temperature, ice maker doesn’t kick in until 12 degrees or colder.

[@farrah2529]

This is the very first video i saved years ago!

[@painter7869]

Are there three retaining plates (two sides and top) or four? Doing the bottom without removing the door appears to be next to impossible.

[@enizzle7]

Do you know if you can dismantle a 650s to access steal panel ... would like to fix a small dent

[@accessorizeagain3019]

Is there a reason why it is super hard to find part number for my 611Sub-Zero door seal and Freezer Seal Please can Same one Help me

[@stdesignall]

Thanks for the help!
Where do I get the subzero part? Any body can help me with this info please.

[@SubZeroSpecialists]

Call Sub-Zero 800
-222-7820

[@danielbouzide884]

On a model 501. 25-year-old Subzero freezer door. Are there adjustments or can the magnets lose their pull. The door won’t close in seal properly

[@SubZeroSpecialists]

You can adjust the top hinge and tweak the door. You may have to remove the two small shipping screws. We have a video on how to remove a door and you can view the process

[@danielbouzide884]

Sub Zero Specialists OK where do I find the video

[@SubZeroSpecialists]

th-cam.com/video/mleN8oh14yo/w-d-xo.html
Try this video it might help you understand how to adjust the door. It’s a different model but the technique is the same

[@davidmiller88ify]

Great Video. My 650 is around 20 years old. The Freezer Gasket is ripped along the top like your video shows. In addition, my ice seems to clump up. I am assuming that the gasket is leaking in some warmer air. What is your opinion on this? (Without actually seeing the unit)
TIA

[@SubZeroSpecialists]

It could be the gasket if it's sucking in warm air, but it could also be the ice maker itself. Change the gasket first and monotor.

[@davidmiller88ify]

@@SubZeroSpecialists TY. Local certified repair has part for Cheaper than online, but also charging $190 for 1st 30 minutes. Your video makes it look simple. How long would it take a novice to do?

[@SubZeroSpecialists]

@@davidmiller88ify Don't buy any parts online, they are not of the same quality, probably made offshore. We charge $300 to install the seal which includes the part. I would reach out to some of my subscribers and ask them about the install. If you watch my other video on the "Principles of door seal installation" that may help you.

[@davidmiller88ify]

@@SubZeroSpecialists TY for the quick response. Going with the professional repair. Their price is in line with yours. Where are you located?

[@SubZeroSpecialists]

@@davidmiller88ify We are located in NJ, NYC and the Hamptons

[@saeidki2269]

Can you please provide me Part# mine is model 650 bottom freezer drawer just like the one you have in video . Thanks

[@SubZeroSpecialists]

You can get part numbers off our website under LOOK UP PARTS at subzerospecialists.com

[@tonycaccioppoli2307]

How much does a freezer door seal cost for a 650 freezer?

[@SubZeroSpecialists]

To buy or to install?

[@benvolz]

How do I get the freezer door off the track to remove it?

[@SubZeroSpecialists]

We have another video that shows how to remove the drawer and you can also peruse our tech help files on our website subzerospecialists.com. All you need to do is pull out the drawer until it stops and then lift it up and pull it off the tracks.

[@lubakaczmar3198]

If you do no want to use a screwdriver for fear of tearing the 200 dollar seal. There is an easy way to install the freezer seal .

[@justinminieri4575]

Your instructions on how to replace was great. However, you never told us how to remove the freezer drawer from the refrigerator. Luckily, one of your comments to your instructions told us how to do to. I assume if you ever told us how to replace spark plugs in a car your instructions would be how to put it in but not how to take it out. A WASTE IF I COULD NOT GET TO YOUR STEP AS IT WAS IN THIS CASE!