Heres a quick video on how i installed a subwoofer into the new 2018 Honda accord. If you have any questions feel free to leave a comment and like the video!
Mark Haley yeah I had to disconnect it. I forgot to mention it in this video but the second video I made on another accord I mentioned it and pointed out it’s location behind the glove box 👍🏼
only video I can find on 18 Accord ,thanks! I have an lx and it's really weak with sound.rockville has a 12" powered sub in a ported enclosure with the wiring kit only $95 !
I have one question. I have everything wired up, but now I am at the point where I need to tap into the speaker wires. There are 2 positive and 2 negative wires. Do I tap into both of the wires?????
@@johnguelfo4840 I ended up tapping the wires to the front speakers at the front kick panels. There's only one single wire for each speaker's positive and negative there. On the forums, there's lots of talk about the rear speakers not giving a full range signal plus the car uses the rear speakers to compensate for road noise so you really don't want to feed the rear signal into an amp.
@@xfiringsquadx So the amp pushes the sub only?...did you use a cross over to eliminate the highs? where can i purchase this remote item you show in the video, never heard of this
@@johnguelfo4840 Yes, the amp pushes the sub only. Don't know what remote you're talking about since this isn't my video. What I used for my installation though was an audio control lc7i. You don't have to use a crossover to remove the highs because any amp designed for a subwoofer would have a built in high pass filter.
Nader 262 did you cut that rubber piece in the firewall to push the battery wire through? I tried pushing mine through but it’s taped with electrical tape from the factory
Grace and Violets toy time. I pushed the grommet out then ran my wire on the side of it. I don’t like cutting factory grommets because of risk from cutting factory wires
He used a hi lo converter with amp turn on to get remote, I used the same one but it turns on the amps when first connected then after a minute turns off, that’s my experience with it
I have a problem I have everything wired up it just i don’t get is when I have the door open it sounds fine bass hits strong and perfect but if I keep the music playing and close any door the bass with just go crazy loud and won’t stop until I open the door again can you try to tell me what I did wrong I have everything wired up the the back speakers but I need to have a door open in order for it to sound perfect and good
Allen Castillo honestly it’s kinda hard to tell without seeing it but are you sure you disconnected the anc? Also go over your wiring and double check your ground
I got a 10’ kicker on my 2018 accord but when the car is cool like in the morning and i start driving the speaker bass just goes up loud when i accelerate with no music. I don’t know what’s wrong with it.
Nader 262 Thanks for such a quick reply. Another question if you don’t mind. I have a dsp and a 5 channel amp. Can I simply run high level (from sub output) to rca adaptor into the processor then rca to amp inputs for the sub? This seems fairly simple if that’s is how I’d do it. I’d love to install my components up front but wasn’t sure how. Do I just tap into door/tweeter speaker wire then to processor just like sub connections? I’ve been reading that the factory amp this car has makes things a bit harder when trying to upgrade.
Also I just disconnect the anc module and still the same thing. It looks like the amp is powering on when the door opens. What were the color wires you taped into on the rear speakers?
Just installed in my accord too oer the weekend. How ever the subs are throwing out really loud sstraight bass befoer the radio even cyces on. And it doesnt sht off unless you turn the car of....Spoke with the guy at the shop I got them from and he said its because of the "noise cancellation"wires, that that has to be disconnected, with out disabeling it then it will cotinue to make that noise ... ever heard of this ?
Nader 262 thanks for the response.. i have kids so i dont want anything crashing around in there in the event of an accident. Im thinking of upgrading the sound system in my accord lx (the WORST model). Would a simple sub insyal make things better?
JRLM if you’re looking for more bass and are worried about sub getting damaged check out my second video I posted on my page. The Rockford fosgate powered sub is perfect for you
I also have a 2018 accord sport. I've been having issues. I get bass increase every time I step on the gas pedal. Any chance u might know what's going on?
calderonpablo83 make sure you have your ground in a good spot with clean metal underneath it. Also check your converter. Could possibly be a bad one. Let me know what happens !
before you do anything, you're not talking about auto volume increase on speed right? Just saying, because you may be coming from old car and not know about this.
Check this site about mid way's down the page www.accordxclub.com/forum/26-electronics-audio-lighting/844-stereo-sub-models-terrible-7.html post by rs7jr with photos as to which wires in the harness are the ones you need to tap
Pipozzz1 it sounds really good for one 12 I tried to post a video with music but TH-cam didn’t allow it so I just made this instead. And for this model I didn’t remove the anc but I worked on a sport model and I did have to remove it.
My car wiring is basically the same but the amp keeps powering up by itself when the CAR IS OFF??? Subs blast constant low frequency until I unplug the rca. I checked all wire connections and have tried 3 different converters. I have the same as you hooked up right now. Also I have sanded the ground and have tried it in 3 different spots. Its also in the same spot as yours now. I have also tried grounding the converter on the amp as well as the frame. Any ideas or suggestions cause I swear I have tried everything.
Hey Spencer where you able to fix the issue? I am having the same problem with the ax adct2 it keeps the amp on all the time even when the car is locked
Nader 262 I used a rca converter box that I got from eBay.. I used the same one one you have and it’s above the sub box. Could it be the input adjustment on the converter? I have the turn all the way up.
I used the Lc2i from audio control. Works great. I tried a pac line out converter but it just didn't have enough power to make the sub hit like it should. The Lc2i makes all the difference. Eventually I plan on installing a second amp to some 6x9s. The Lc2i does have sub output rca and main output rcas so you can install two amps.
88omarz if you live around Kenosha Wisconsin then you can swing by my shop! In this install we are using an American bass dx12 with an auto tech 1000watt amp
I’m going to try to do this same thing to my 2018 Accord. What all did you need outside of subwoofer and amp? I know there’s plenty more I just don’t know what I need to buy. I have a buddy that understands the mechanical part but I want to make sure I have everything he needs before we start. Thank you!
Hi,I installed a VPAS 10 using the ax-adct2 wired to the back speakers, if I connect only one of the two rca cables I get stronger bass, when I connect both the sound gets reduced by a lot, already tried changing the polarity of one of the pair of cables connected to one of the speakers but it still doing the same, the same happens using any of the two rca input channels
Nader 262 Thanks for the fast reply, I haven't do that because it's a integrated amp sub, similar to the hideaway, do you think that could be the issue?
does it matter which wires are tapped for rear speakers? I've noticed there are 4 wires per speaker where adapter connects. Also, very good job on install. Looks clean. Also, what size box is that? looks like 10" woofer?
Cold Rainer there are two wires per speaker. And yes sir it matters you have to make sure positive and negative are correct. You don’t want the wires to be inverted other wise the speakers will be out of phase ! And thank you I appreciate it. Also it’s a 12inch subwoofer 👌🏼
thanks for your reply. I understood positive and negative but my speaker adapter has 4 wires(Sport 1.5t). Was this LX version? that could be a reason. Would you happen to know which wires need to be tapped if i have 4 wires?
Cold Rainer ooh ok that must have been a different model then. I think in your case your speaker has a separate mid and tweet so you need to find the wires that are for the mid and tap into those
alright I'm back. so I see that these are actually component and not coaxial speakers. Meaning, tweeters are separate from rear speakers and they have their own wires(2) going to it. So I'm bit stumped regarding 4 wires. I hate to tap in to all 4 wires on each side and have only 2 wires run to line out converter. Anyone with solution?
Nader 262 wow cool I'm buying a 2018 accord touring and the speakers are not all that great should have been a stock 1000watt setup like Audi and others but I do live in Appleton I'll have to swing by
Thanks for the video, this is awesome stuff! Did you have to cut into that rubber hole to get through the firewall??? Or were you able to just push through with the factory wires.....it looks like your power wire is running to the right of the rubber hole opening...
Jarvis Sparks thank you ! And I pushed the grommet out so I can slide the wire to the side of it and I loom the wire so it doesn’t get pinched between the metal and the grommet. I don’t like to cut through the grommet where the factory wires are for the fact that I don’t want to damage any factory wires and cause a problem
Thanks for responding bro, going to give this a try in a few days. Doing an install on my 2018 and this is step one, your video/help is much appreciated.
Hello, I installed a kicker hideaway under the passenger seat, Now I also bought the kicker converted, And when I accelerate turn on the car and drive it and the RPMS go around 2K the subwoofer makes a loud HUMM... bass, Did you happen to know what wires to get them from on the back speaker there is 4 wires on each speakers, Not sure if maybe my converter I got from kicker is not the one for that cause. Or something is not hooked up correctly.
How the hell did you manage to get the power wire though and grab it ?? Lol
did you have to disconnect the ANC system? Most times, I have heard that its a must or else you'll get nasty feed back when the stereo is playing
Mark Haley yeah I had to disconnect it. I forgot to mention it in this video but the second video I made on another accord I mentioned it and pointed out it’s location behind the glove box 👍🏼
Show me how to put a fuse adapter into a fuse with a toggle switch for amp turn on
How much Do you do charge for installation?
what fuse is good
only video I can find on 18 Accord ,thanks! I have an lx and it's really weak with sound.rockville has a 12" powered sub in a ported enclosure with the wiring kit only $95 !
andrew zweiger awesome glad I could help!
th-cam.com/video/zyfLvj2YQag/w-d-xo.html
I have one question. I have everything wired up, but now I am at the point where I need to tap into the speaker wires. There are 2 positive and 2 negative wires. Do I tap into both of the wires?????
I need to know this too
@@xfiringsquadx apparently he does not want to share
@@johnguelfo4840 I ended up tapping the wires to the front speakers at the front kick panels. There's only one single wire for each speaker's positive and negative there. On the forums, there's lots of talk about the rear speakers not giving a full range signal plus the car uses the rear speakers to compensate for road noise so you really don't want to feed the rear signal into an amp.
@@xfiringsquadx So the amp pushes the sub only?...did you use a cross over to eliminate the highs? where can i purchase this remote item you show in the video, never heard of this
@@johnguelfo4840 Yes, the amp pushes the sub only. Don't know what remote you're talking about since this isn't my video. What I used for my installation though was an audio control lc7i. You don't have to use a crossover to remove the highs because any amp designed for a subwoofer would have a built in high pass filter.
Could you provide links for the sub, amp and wiring etc wanna install this on my car. Thanks in advance
Nader 262 did you cut that rubber piece in the firewall to push the battery wire through? I tried pushing mine through but it’s taped with electrical tape from the factory
Grace and Violets toy time. I pushed the grommet out then ran my wire on the side of it. I don’t like cutting factory grommets because of risk from cutting factory wires
Nader 262 yes I almost cut a wire.
Grace and Violets toy time. Yeah that’s why I don’t recommend doing that. Just push the grommet to the side and run your wire
Nader 262 what fuse did you use for remote wire?
Can I personally dm you I’m trying to find a ground wire I need help please
Hey bro, how much does it cost for installation? My car is Honda Accord.
John May where are you located man ?
Questions about the rca signal from the actual radio how was that connected
I’m confused where are your RCA’s going to?
The converter. I know this is late but incase anyone else is wondering.
@@Motinhox Thanks for the response :) I got it figured out in my vehicle.
Where did you hook up the remote wire to??
Thank you
Valentino Life get an add a fuse and find a fuse with no power when key off and then power with key on plug it in there
He used a hi lo converter with amp turn on to get remote, I used the same one but it turns on the amps when first connected then after a minute turns off, that’s my experience with it
I have a 2020 honda accord sport how do you charge to install a lc7i audio control with a 4 channel amp with sub and amp? Thank you.
How did you hook up to factory radio
Looks very nice...how much$$
I have a problem I have everything wired up it just i don’t get is when I have the door open it sounds fine bass hits strong and perfect but if I keep the music playing and close any door the bass with just go crazy loud and won’t stop until I open the door again can you try to tell me what I did wrong I have everything wired up the the back speakers but I need to have a door open in order for it to sound perfect and good
Larry Valenzuela disconnect the anc. Watch my second video for better explanation
I’m curious how much you’d charge to do this I’m very close to Kenosha and am looking to get this done
Did you have to unhook ANC
Did you change out your other speakers if not how does it sound
What adaptor is need for the touch screen
Nader262 do you know why I'm getting feedback in my system disconnected anc plug and getting noise when I accelerate
Allen Castillo honestly it’s kinda hard to tell without seeing it but are you sure you disconnected the anc? Also go over your wiring and double check your ground
@@nader2627 thank you I will double check everything
I got a 10’ kicker on my 2018 accord but when the car is cool like in the morning and i start driving the speaker bass just goes up loud when i accelerate with no music. I don’t know what’s wrong with it.
Daniel Valles you have to disconnect the ANC brother. I mentioned that in my second video 🤙🏼
Thanks man! it’s good now
Daniel Valles no problem brother 🤙🏼
My 2019 EX-L has the premium 10 speaker w/ subwoofer. Would I grab signal from the sub speaker wire instead of the fronts?
Millz1273 thats what id do !
Nader 262 Thanks for such a quick reply. Another question if you don’t mind. I have a dsp and a 5 channel amp. Can I simply run high level (from sub output) to rca adaptor into the processor then rca to amp inputs for the sub? This seems fairly simple if that’s is how I’d do it. I’d love to install my components up front but wasn’t sure how. Do I just tap into door/tweeter speaker wire then to processor just like sub connections? I’ve been reading that the factory amp this car has makes things a bit harder when trying to upgrade.
Also I just disconnect the anc module and still the same thing. It looks like the amp is powering on when the door opens. What were the color wires you taped into on the rear speakers?
Hey man im trying to do the same set up in my accord i just dont know how to connect the converter to the car HELP PLEASE
How much$$
Just installed in my accord too oer the weekend. How ever the subs are throwing out really loud sstraight bass befoer the radio even cyces on. And it doesnt sht off unless you turn the car of....Spoke with the guy at the shop I got them from and he said its because of the "noise cancellation"wires, that that has to be disconnected, with out disabeling it then it will cotinue to make that noise ... ever heard of this ?
Mel C yeah bro you need to disconnect the ANC and it’ll sound much better
Gunna try it shortly. I’ll let you know the outcome. The issue is always next day 🙄 we’ll see what happens
Mel C sounds good man I’ll try to help you out as much as I could
How did you connect the amp wire to the battery terminal? Mine won’t seem to fit.
same issue I have
what keeps the sub from bouncing around in the back of the car?
JRLM i usually use strips of thicker Velcro that sticks well to both the box and the carpet flooring
Nader 262 thanks for the response.. i have kids so i dont want anything crashing around in there in the event of an accident. Im thinking of upgrading the sound system in my accord lx (the WORST model). Would a simple sub insyal make things better?
JRLM if you’re looking for more bass and are worried about sub getting damaged check out my second video I posted on my page. The Rockford fosgate powered sub is perfect for you
How much better does it sound with the sub?
Help meee I’m from Cali
I also have a 2018 accord sport. I've been having issues. I get bass increase every time I step on the gas pedal. Any chance u might know what's going on?
calderonpablo83 make sure you have your ground in a good spot with clean metal underneath it. Also check your converter. Could possibly be a bad one. Let me know what happens !
Nader 262 thanks I'll double check my connections and see about another converter.
calderonpablo83 sounds good key me know
before you do anything, you're not talking about auto volume increase on speed right? Just saying, because you may be coming from old car and not know about this.
Cold Rainer it's very possible that's the issue, I still haven't figured out how to bypass it....
Nice job man. One thing I can't seem to find is anyone doing a full speaker upgrade. No one even seems to know the stock RMS per channel.
Billy Mangino thanks man ! And I haven’t had any customers come in yet to do that but if I do I’ll definitely post it !
How did you mount your sub box ???
I am trying to tap into the right front door speaker at the kick panel. Anyone know the color wires and which harness? 2018 sport
Check this site about mid way's down the page www.accordxclub.com/forum/26-electronics-audio-lighting/844-stereo-sub-models-terrible-7.html
post by rs7jr with photos as to which wires in the harness are the ones you need to tap
J Hickman civic 2019 link??
where did you find ground?
what does it sound like bro? lets here it lol. thnx for the vid as well im going that route as well, did u remove the anc plug?
Pipozzz1 it sounds really good for one 12 I tried to post a video with music but TH-cam didn’t allow it so I just made this instead. And for this model I didn’t remove the anc but I worked on a sport model and I did have to remove it.
My car wiring is basically the same but the amp keeps powering up by itself when the CAR IS OFF??? Subs blast constant low frequency until I unplug the rca. I checked all wire connections and have tried 3 different converters. I have the same as you hooked up right now. Also I have sanded the ground and have tried it in 3 different spots. Its also in the same spot as yours now. I have also tried grounding the converter on the amp as well as the frame. Any ideas or suggestions cause I swear I have tried everything.
spencer weeks ---you need to disconnect the ANC(AudioNoiseCancellation module above the glove box).
Hey Spencer where you able to fix the issue? I am having the same problem with the ax adct2 it keeps the amp on all the time even when the car is locked
I ran the remote wire from amp to the cars on/off button fixed this problem
I have a 2019 sport, how much does it cost for this setup?
527mike where are you located ?
I want to do the same setup on my accord what did you use?
Did this accord have a factory amp ?
I put my ground in the same place you said to put it and I hear the car engine in my subs. Did you have any issue with it?
I Rod72 I had no issues with them. Did where did you go for your rca signal?
Nader 262 I used a rca converter box that I got from eBay.. I used the same one one you have and it’s above the sub box. Could it be the input adjustment on the converter? I have the turn all the way up.
did you use a inline fuse for your big 3 upgrade?
I have a 2019 accord
When im driving my sub hums why is that
Joe Mainez I’m getting the same thing. I think the rear speakers on the 8 channel models have sound reducing in the rear speakers
@@RusselltheMuscle121 I figured it out it was the noise cancelling the car has its located behind the glove box u have to unplug it
Thanks for the video!
Hello Brother! a question where to connect the remote of the amplifier so that it turns on with the stereo??
Fuse box in driver kick panel
@@nader2627which fuse
What fuse number?
What hi to low did u use? I wanna install 2 amps. What would u recommend?
Tim Scott look up audiocontrol or wavtech. Both companies are great
@@nader2627 I was gonna order the audiocontrol lcq1.
@@nader2627 where u do installs at?
I used the Lc2i from audio control. Works great. I tried a pac line out converter but it just didn't have enough power to make the sub hit like it should. The Lc2i makes all the difference. Eventually I plan on installing a second amp to some 6x9s. The Lc2i does have sub output rca and main output rcas so you can install two amps.
Nice and clean installation. Wish I was in ur state to get some work done! Did u swap out a new head unit or is that the stock unit?
b3ar0fab thanks man I appreciate it ! And the customer kept the factory head unit
Nader 262 yup I have the factory head unit works fine with my 2300 watts
Do you have to tap into both speakers? because mine is only on one side.
I too would like to know. i will be doing the install on my 2018 Sport 2.0
Any updates on this?
what system are you using, where can we get it?
88omarz if you live around Kenosha Wisconsin then you can swing by my shop! In this install we are using an American bass dx12 with an auto tech 1000watt amp
I’m going to try to do this same thing to my 2018 Accord. What all did you need outside of subwoofer and amp? I know there’s plenty more I just don’t know what I need to buy. I have a buddy that understands the mechanical part but I want to make sure I have everything he needs before we start. Thank you!
Ps. I have a Rockford Fostgate 1000w amp and a Rockford 10 inch sub too. Just in case a need stronger cables
Spencer Hemmer 4 gauges wiring kit and a line out converter
Hi,I installed a VPAS 10 using the ax-adct2 wired to the back speakers, if I connect only one of the two rca cables I get stronger bass, when I connect both the sound gets reduced by a lot, already tried changing the polarity of one of the pair of cables connected to one of the speakers but it still doing the same, the same happens using any of the two rca input channels
Marcos Chavez hey man. Did you double check the sub wiring inside the box ?
Nader 262 Thanks for the fast reply, I haven't do that because it's a integrated amp sub, similar to the hideaway, do you think that could be the issue?
Marcos Chavez ooh ok i didn’t know it’s a powered sub. Did you try reversing the polarity on the one rca that makes the mass reduce ?
Nader 262 Yes, I changed the polarity on one of the rca's and still when I connect only one (it can be either) the sound is stronger
Marcos Chavez by any chance did you adjust the gains on the converter ?
does it matter which wires are tapped for rear speakers? I've noticed there are 4 wires per speaker where adapter connects. Also, very good job on install. Looks clean. Also, what size box is that? looks like 10" woofer?
Cold Rainer there are two wires per speaker. And yes sir it matters you have to make sure positive and negative are correct. You don’t want the wires to be inverted other wise the speakers will be out of phase ! And thank you I appreciate it. Also it’s a 12inch subwoofer 👌🏼
thanks for your reply. I understood positive and negative but my speaker adapter has 4 wires(Sport 1.5t). Was this LX version? that could be a reason. Would you happen to know which wires need to be tapped if i have 4 wires?
Cold Rainer ooh ok that must have been a different model then. I think in your case your speaker has a separate mid and tweet so you need to find the wires that are for the mid and tap into those
Cold Rainer I believe it’s yellow-brown and pink- white for your mid. Yellow and pink being positive
alright I'm back. so I see that these are actually component and not coaxial speakers. Meaning, tweeters are separate from rear speakers and they have their own wires(2) going to it. So I'm bit stumped regarding 4 wires. I hate to tap in to all 4 wires on each side and have only 2 wires run to line out converter. Anyone with solution?
How much would labor cost? I believe I have all the wires and cables.
I’m located by Mason City Iowa
We are located in Kenosha Wisconsin man !
Nader 262 wow cool I'm buying a 2018 accord touring and the speakers are not all that great should have been a stock 1000watt setup like Audi and others but I do live in Appleton I'll have to swing by
Kevin Artz cool man swing by with it !
Thanks for the video, this is awesome stuff! Did you have to cut into that rubber hole to get through the firewall??? Or were you able to just push through with the factory wires.....it looks like your power wire is running to the right of the rubber hole opening...
Jarvis Sparks thank you ! And I pushed the grommet out so I can slide the wire to the side of it and I loom the wire so it doesn’t get pinched between the metal and the grommet. I don’t like to cut through the grommet where the factory wires are for the fact that I don’t want to damage any factory wires and cause a problem
Thanks for responding bro, going to give this a try in a few days. Doing an install on my 2018 and this is step one, your video/help is much appreciated.
Jarvis Sparks no problem man glad I could help
Dude can you please upload a video on how to upgrade interior stock speakers including sizes....no one has this yet!
Edgar Rodriguez hopefully someone will come in to get them upgraded man ! If I get someone in I’ll post it !
Dude you can replace my speakers....but I live in Miami! LOL
Edgar Rodriguez haha if you wanna drive to Wisconsin I would !!
crutchfield.com jbl stadium series components fit under stock grills
Brandon Dybalski have you replaced yours? If so do you have a video?
Is this your car?
mark salvaleon no sir it was a customers vehicle
Nader 262 ohh cool! How much did u charge? I have the same car and I was wondering what I should expect to pay
mark salvaleon with wires , parts and labor it was about $200. Sub and box were extra
Were your shop
I have the same problem with my car the sound on the woofer
Jose Canizales we are located in Kenosha Wisconsin. Sound on wheels
Ok I'm going to try to get the same RCA signal the you install it may work better I'm located in L A thanks
Jose Canizales no problem man !
Hello,
I installed a kicker hideaway under the passenger seat,
Now I also bought the kicker converted,
And when I accelerate turn on the car and drive it and the RPMS go around 2K the subwoofer makes a loud HUMM... bass,
Did you happen to know what wires to get them from on the back speaker there is 4 wires on each speakers,
Not sure if maybe my converter I got from kicker is not the one for that cause.
Or something is not hooked up correctly.
Bryan Margain hey Bryan. You have to disconnect the anc to get rid of that noise. Watch my second video for an explanation !
Bryan Margain You gotta disconnect the anc in the back of the glove box