Junkyard LQ4 6.0 LS on the Runstand: She’s A Runner
ฝัง
- เผยแพร่เมื่อ 4 ต.ค. 2024
- Taking our most recent iron block 6.0 and throwing it on the runstand to test. I decided to not flip this engine over and pull the oil pan first before running it. This resulted in quite the emotional rollercoaster.
www.newvintageusa.com
use code:TravisBlack for 10% off your total
Garage lighting by: garagedoorlighting.com
If anyone would be interested in purchasing this engine, any of my other engines, or is looking for any specific GM engine or transmission combo please comment below or find me on Instagram
If you are interested in having me fully inspect and test run your personal LS engine on my runstand please also reach out.
Carb:
www.holley.com...
Intake manifold:
www.holley.com...
Ignition:
www.holley.com...
Headers:
www.holley.com...
nieghbors must LOVE you.
@12:52 when he rolled the part on the dirty ground then threw it back in the engine 😅😅😅😅
Dude is a freaking book……😂👍👍👍
It’s more convenient to just memorize all this stuff rather than have to look it up
I could tell, right away that this was a lifter issue. I built my engine stand using a GM LS (aftermarket universal gen III, IV, V swap controller kit) controller kit I found in a junkyard. I have a trick you should try next time: pour two capfuls of ATF right on top of the lifters, then fire it up. You might need to repeat the process 2-4 times, but it has worked every time for me.
Cool video! Your one of the people who inspired me to go pull 42 engines out of my local yard the last four years. Only had to bring back three..keep them coming!
What were those 3 failures you found?
How much for a good running 6.0 shipping available?
@@The918OBS send me a message on IG
@@travisblack417 1 head gasket1 lifter tick 1 had endplay.
@@The918OBS currently only one 5.3 and two that run but one knocks, one had a tick but it cleared up. Need to run it more.
I've had good luck running Sea Foam in engines to clean up a noisy lifter. It also has the added benefit I think of loosening up any gunk on the oil control rings. But, I don't have any proof of that. (I've also rolled the engine so one bank is upright and put Sea Foam in each cylinder to loosen up the rings also. Let is sit overnight, you can tell how bad the rings are by how fast it leaks down into the pan). But, it has cleaned up lifter noise on several engines I've used it on. Dump a can in and let it run 30 minutes or so and change the oil again. Been surprised how black the oil comes out also. I've never dumped it down the intake as others have suggested while running. Just my experience. ATF also has a lot of detergent in it. I've used that in the past also. A couple of quarts in with the oil and let it run at idle or low rpm for a while and drain. Nice engine stand. Working on one myself I can tow behind my truck. Be like a mobile mechanic, for people that can't come to you.
How dirty were the engines that you seafoamed? This motor is genuinely one of the cleanest motors under the valve covers that I’ve ever pulled. I’ve had motors with 1/2” of sludge in the pan and blackness under the valve covers with zero noise.
Yeah, that sludge quiets them down quite a bit also. lols. I don't buy those sludged up engines. Just because I hate the thought of having it in there. And afraid the sludge would break loose if I tried to clean it with this method. Before I installed the engine, I pull it down to the long block to replace all the oil seals and gaskets. Don't generally pull the heads either as I can fix the broken exhaust studs on the engine stand. Can't have things too clean inside and engine. Thanks for the video
My goal is to sell engines to people before I open them up, then it will be up to the customer as to how far I tear into it cleaning it up (pulling heads to change lifters etc)
Great vid
I have a 2005 5.3 WOkittycats with a dump valve, bypasses every thing. It’s not bad until u rev it 2 the moon…..close the valve on goes thru a hurst Quite muffler…..
Hey travis you really want to know what that noise is?? use a mechanics stethoscope you will know real quick what it is and isolate the cause
Honestly a stethoscope would probably be better than a bore scope lol.
Maybe a trunion bearing on the rocker that is cockeyed
That's what I thought too
super rad!
So much better video than arguing with a drunk.
It's been said before,, You're a wealth of knowledge... And it needs to be absorbed in a calm setting. Thank you.
Bad Ass El Camino
Thank you
Looking for a
ford 300 cu for 1965 f100
How much are you looking to get for the engine. $$
Send me a message on IG
Nice video man I would like to talk to you abt a few things motor run stand ect very much interested trying to do a swap on a few cars
Send me a dm on insta
Can u find me a 6.0 and run it on the stand I’ll buy it willing to drive from Arizona if I have to
No bs I’ll call off of work and head to cali I need it for my 1972 impala
Is this sold?
Please help I having the same problem, what did you actually do? I have replaced just about everything on the motor just to find that same noise again. Very frustrating. Please help
What noise?
Lifter knocking
How did you bend the muffler system?
U buy them that way from the parts store
How about 8.1l
What about it?
You do nice work sir
@@BrianArsenault-r3q thank you
Where you located
Thousand Oaks