Cheap and Simple Radio Control Making for RC Models. DIY RC 4-Channel
ฝัง
- เผยแพร่เมื่อ 18 ก.พ. 2020
- How to make a low cost 4 channel radio control for RC model aircraft, drone, cars and boats.
Construction of remote controls with proportional controls, which cost about 13-14 USD. It can be used for all kinds of model vehicle control such as model aircraft, drone, car, boat, tank.
Thanks for watching. If you want to support my channel, join.
/ @kendin-yap
Necessary materials:
2 x Arduino Nano
1 x NRF24L01 + PA Wireless Module
1 x NRF24L01 Wireless Module
2 x Arduino joystick
2 x 100uF Capacitor (16V or above)
1 x Min. 13 * 6 cm PCB Board
1 x 5 * 3.5 cm PCB Board
Arduino Nano: www.banggood.com/custlink/vvG...
Arduino Joystick: www.banggood.com/custlink/333...
NRF24L01 Wireless Modul: www.banggood.com/custlink/KGv...
NRF24L01 + PA Wireless Modul: www.banggood.com/custlink/33G...
20A Brushed ESC: www.banggood.com/custlink/D3D...
PCB Boards:
www.banggood.com/custlink/KmD...
www.banggood.com/custlink/3vG...
100uF Capacitor: www.banggood.com/custlink/DKD...
Headers:
www.banggood.com/custlink/m3v...
www.banggood.com/custlink/vG3...
Other materials:
SG90 Servos: www.banggood.com/custlink/Kv3...
20A ESC: www.banggood.com/custlink/mvv...
7.4V 450Mah 2S LiPo: www.banggood.com/custlink/KKK...
DC 180 Motor 39000 RPM: amzn.to/35rD8Ar or bit.ly/2L62JqC
3M Dual Lock Tape: www.banggood.com/custlink/K33...
Wire Stripper Tool: www.banggood.com/custlink/mDm...
Iron Soldering DANIU PX-988 90W Digital Thermostat Adjustable
ban.ggood.vip/RvRz
DIAGRAMS & CODE: tinyurl.com/ynj88zk6
Setup & Code Upload Tutorial: Arduino IDE, library files setup and code upload : • Arduino IDE Installati...
My Web Site (KendinYap): www.rcpano.net
All of my videos : bit.ly/2Z9QVYK
Thank you for watching. Please Remember to Share and Subscribe for More Amazing Videos.
25 years ago, when i started in RC airplanes this was impossible to only think about! Today, micro-genius like you , with arduinos help, can do whatever you want! Great job! 😎✌️
i wish ı have rc airplanes
İm started 12 years ago im now 13
@@Emre-ff3xw 🤣🤣🤣🤣
@@Emre-ff3xw LOL
@@Emre-ff3xw kuch vhii🤣🤣🤣
one of the different thinking tech youtuber you are.great effort.cheers.
This is the kind of project I wanted to build back in 2004-2005 but never got the detailed knowledge on how to do it. Back then I was completely self taught and just a regular curious dude, without much access to the internet etc. Then later got into web development stuff and never really went back to electronics. But it's nice to see how it's done, also with new components like arduino and wifi module which back then wasn't quite easy to find.
Tnx for your reply 👍
Apakah ada jenis micro controller lain dari arduino ini ?
Pada saat itu anda menggunakan apa dalam pemrograman
Hello and thank you, You have opened up a whole new world for my rc projects. I am going to use what I have learned from you to convert some old Futaba radios to use Arduino rc Thanks to you Awesome job.
can I use brushless motor with this receiver, pls reply me.
Thanks a lot bro, you save my proyect, you are the first one to have a well explained code
Bro tell me how to load the code plzz bro
Terima kasih telah berbagi ilmu, semoga bermanfaat bagi orang banyak.
Great jobs !!! For RC Plane, if you want to make it cheaper, you don't have to buy 20A Brushed ESC. Just add a Mosfet (for example: IRF3205), a diode and a resistor, then connect it to brushed motor. Of course you need to modify the receiver code. So, the Arduino control the mosfet using PWM. Cheers..... !!!
What will be the overall cost of this project could u tell pls?
Around 1500 INR
Cuman mosfet doang panas banget bro😅
Simple if you understand electronics. I've got supplies for experimenting but my health caught up with me. Hands aren't any good anymore. All my fingers are out of place. I can still use them but it puts stress on my muscles and that causes toxins to build up in me. Doctors told me one day I'll be doing an activity and suffer catastrophic organ failure just simply fall dead where i stand. Kind of scares me doing anything foolish. I joked with my dad I'm going to be cleaning the toilet and fall down dead. Told him he'd have to put on my tombstone I was killed by a toilet. Not that I want to die anytime soon but I don't want to be killed by a toilet. Kind of sucks not being able to do nothing. Thanks for the videos. I do enjoy watching other people be creative.
Hocam Projelerin çok açıklayıcı ve bilgilendirici Emeğine sağlık
This is exactly what I am looking for. Thanks
AMAZING pretty soon hoping to start up my soldering projects never soldered before love the challenge of creating stuff
Thanks to you I made my own ! the joysticks were trash so I bought a dead radio transmitter and used it's joysticks !
Hep yapmak istediğim şey ama hiç başaramayacağım. Ağzıma açık tüm videolarını hayranlıkla izliyorum. Teknolojiyi hiç bu kadar açıklayıcı görmemiştim. Başarılar dilerim
göründüğü kadar zor değil. konunun içine girdikçe kolay olduğunu göreceksin. biraz araştırdıktan sonra tek engel maddiyat olacak.
@@piekovski benim öncelikli engelim vasküler demans hastası olmam çok büyük sorun. Fizik konularında da çok iyi idim keşke Almanya'da yada Japonya'da gibi eğitim sistemimiz olsaydı ve benim ve benim gibilerin yeteneği ziyan olmazdı.
@@piekovski arduino proje seti aldim bunu yapmak istiyorum nasıl bir yol izlemem gerekiyor
Turker Candemir öncelikle başlangıç seti aldıysan eğer orada ki projeler ile pratik yap ondan sonra böyle projeleri yapmaya çalış daha da yardıma ihtiyacın olursa buraya yazabilirsin elimden geldiğince yardımcı olurum
@@merttas4886 hocam bu bağlantıların mantığını daha iyi anlamam ve kendimi geliştirmem için önerdiğiniz bir kanal veya eğitim platformu var mı ?
That's what I've been searching! Thx
its,s work or not
Work
Eu sou do Brasil mas eu acompanho seus vídeos desde sempre acho muito legal vou até me inspirar nesse projeto
These days everyone is using costly flight controllers and stuff. Its fun to watch this implemented without required sensors and GPS...etc. Thanks for making this video, making people realize that a plane can be flown with basic curcuitery as well, fancy flight controllers are not needed :P Thanks again :)
Ellerine Saģlık. MADE IN TURKEY
you lose vs Italy on first game Euro 2020, AND WE WONNNNNNNNNNNNNNNNNN WE ARE THE WINNER OF EURO 2020
Türkiye’deki diğer TH-camrların aksine çok iyi projeler ve yaratıcı fikirlerle dolusun. Çok iyi bir kanalın var, tebrikler 👏🏻
سلام
quite noble adamın fikirleri yaratıcı
Чё чё?
@@user-xq9ou7pr6q я тоже все это прочитал и нихуя не понял
может через зеркало читать нужно XD
@@user-xq9ou7pr6q mal
Thank you very much! I was trying to find cheap and good controler and reciever on arduino, your tutorial is the best
Wow dude, you have explaned code well in description link, that's amezing we want more exploring video .
You are amezing.🤘🤘😀😀♥️
Hmmm, nice!
Hai electronoobs
Hai electronoobs
@Renzo Guzzo why
Electronoobs I am asking you for a request and please help me. I want the code for the Arduino, please, not an order
@@MridulHasan380 vai apni ki eta try korechilen?
Excellent craftsmanship and soldering skill. Job well done :)
You are super bro I have seen many videos to make it but I fail 5to8 times then I saw your video and I succeed YOU ARE MY IDEAL BRO ❤🎉🎉🎉🎉
It works or not
To do all this should opt for electrical engineering branch..
Or electrical and communication branch Please reply
I made a radio controller, your video was very helpful to me, thank you!
bro can u give code and cercuit diagram
@@rezaulhasan4858 th-cam.com/video/f1z8Wvy56t8/w-d-xo.html
can I use brushless motor with this receiver, pls reply me.
Bro...
You opted for electrical engineering branch or which branch to learn all this
Thanks for this amazing project, I love your code too much. You are amazing.👍👍👍
Can you help me for the coding
I try in my android but it showing pls complete sketch pls help me
can I use brushless motor with this receiver, pls reply me.
Esta excelente este video!!! 😍👏👏👏Sería lo más de bueno si también se le pudiera poner una pantalla con menú
Can this be integrated into an RC toy car? Say for upgrading transmission connection or simply replacing the stock remote controller with this one.
can't you use something like a NODEMCU module that have both a computer and wifi antenna?
just asking because that is more confined.
Thanks man. Now I can complete my project . Thank you so much 😊😊😊😘
Its working or not
Yine süpersiniz hocam. Tebrik ediyorum.
Hey, amazing video!!
I was wondering if it is possible to use my laptop keys as the servo controller. Use a wifi antenna as the receiver and the Arduino and wifi module as the transmitter. If possible could you elaborate a little?
Yeah it's possible
i suggest to use a 3.3v voltage regulator to the NRF24, the arduino regulator is not enough, that's why it hadn't enough signal range when u tested it
This will reduce the weight of rc plane!! Thanks bro.
also saved me so much money!!
Does your transmitter work
It would really help if you released the unedited part without music and speed up with commentary/tutorial. Gives people more options and you cover the experiences people that understand at a blink of an eye what your doing and then for the newbies a solid background of what to think back on when I keep doing research. Hope I can make this work as you did thank you for the video
With this setup is there a way to detect and disconnect/send warning, when the liPo (either in remote and motor) is reaching damaging discharge of about 6V?
For remote I would just add lipo protection board, for plane same. If you want to get signal from plane, you should use same RF chip, as in remote, and then give led to blink, ar even better add OLED 0.96 screen on remote.
THANKS BRO FIRST I COULD NOT UNDERSTAND DIAGRAM THEN SAW YOUR VIDEO PART NOW I CAN MAKE MYSELF A MISSILE!
Mükemmelsin abi senden kalitelisi yok
Brilliant!! Well done and many many thanks for sharing this with us all on here. I love your videos and really look forward to them. I shall be making one of your plane builds soon and I will see if I can make it fly. Please keep these videos coming, they are so interesting and informative.
Many Thanks & Have Fun,
Joe
Thank you
guys,you say what I want
@@Kendin-Yap Hlo frnd if I connect the receiver to a flight controller like omnibus or anyother flight controller will it work friend???.Bcoz I am planning to make these for my project.
can I use brushless motor with this receiver, pls reply me.
I have one question. If someone using same module or other radio frequency can create interference or not in communication .
What range do you have with just one transmitting antenna and no receiving antennas? I'm not sure if I should buy two "NRF24L01+PA+LNA". (I'm making a boat)
70-80 meters (ground to air). For the surface it is much less. For more, both should be PA+LNA.
excellent project, I would like later a video implemented in an airplane to see the operation thank you very much
Thanks. I will make an airplane project with this remote.
@@Kendin-Yap plz can you do it with 6 servos.thank you nice project
excellent! wish you success!
Merhabalar Kendin Yap Kanalı,
Ben sizin de tasarladığınız controller olmak üzere TH-cam'da bir çok kanalın tasarlayııp yaptığı controllerda Arduino Nano kartını kullandığnı gördüm Peki benim sorum : Arduino nano'nun donanımsal veya tasarım olarak size controller yaparken diğer kartlardan ayrı olarak sunduğu ayrıcalıkları ve bu ayrıcalıklardan en önemlisi nedir?
İyi Akşamlar
Hay bro thanks you... You cool 👏👏👏. Your smart n genius. Amazing very amazing project
hocam rc uçaklarda kullanabileceğimiz yarı porfesyonel diyebileceğimiz bir model daha yaparsanız cidden çok güzel olur
Abi fırçasız esc yaparmısın el yapımı çok merak ediyorum
Keşke malzeme listesi linkleri koysanız da bizde aramasak
Çok güzel video teşekkürler
Would please tell me that there will be a frequence hopping technique which helps us to keep away from intruders, i hope it cant be done with an 8 bit microcontroller,
Thanks for show us. For sure I'm going to try to do it. Which is the maximum range you have found this radio control has?
The theoretical range is 300-500 meters. Soon I will test this remote with a model airplane and publish its video.
Wating
0:14 - the schematic
Bunu 2 kanallı RC araba için yaparmisin kumandası da RC car kumandası olacak şekilde çok güzel olur :)
HI sir, thankyou for your idea ,i made this as my school project and it works ,,thankyou sir
Please make the plane of this transmitter and receiver fast
I am waiting for the plane from this remotcontrolar
He uploaded months ago a diy plane. Maybe they are combinables
Gracias por el video !!!!
Ojala encuentre en mi pais los componentes !!!!!
I am suitably impressed.
Abi merhaba.Devreyi kuruyorum ama çalışmıyor.Birde esc ti açınca ötüyor.
Mano que legal achei top 😁👍
🇧🇷🇷🇺
Nice video
Bonjour
Excellent travail bravo 👏 👍 👌
Superrrrrr 😊😊😊 ilkkk
Hocam yaptım valla yaptım çok mutluyum kumanda çalışıyor , aşırı mutluyum tam 1 senedir bu projeyi yapmaya çalışıyorum para biriktirip malzeme tedariği sağladım 3 ay içinde Arduino kullanmayı öğrendim küçük projeler yaptım 1 ay sonra lehim yapmayı öğrendim sonunda kendi kumanda mi yaptım Allah senden razı olsun, kumanda alsam 400tlm gidecekti ve bir heves olup gidecekti sayende Arduino kullanmayı öğrendim ve 100 TL'ye kendi kumandami yaptım.
Lipo pil kullandın mı yoksa normal ucuz 12v luk pillerden mi kullandın
@@Zagrex ben kumanda da usb kullandım ama alıcıda ise 3s lipo kullanıyorum
@@veyselustundag7168 kumandada 2s lipo pil kullanmış biz 12v luk normal pillerden kullsak olur mu acaba lipolar çok pahalı
@@Zagrex 12 v klon Arduino ya yüksek geliyor mümkün olduğu kadar 10v gecmemeye çalışın , 9v pil kullanabilirsiniz
@@Zagrex 12 v tavsiye etmez bir çok kişi klon Arduino da yanmaya sebepmis
Nice and deep explanation thank you
Daha önce yapmış olduğunuz çift motorlu botta bu kumandayı kullanmak için neler yapmam gerekir yardımcı olur musunuz? Sadece yazılımsal değişiklikler yeterli olur mu?
interesting! :-)
Greetings from Mexico. Is difficult for me to find all the materials. It would be great if you could post a diagram using brushless esc and motor (seems these parts are very common in mx). I am very new to this and can't figure it out on my own, also, can see other people is asking for the same.
Thanks in advance.
You can use brushless ESC and motor. There is no need for a change for this.
It is very cheap ..... Thanku bro 🥰🥰
Thank you so much brother. Looking forward to make this whenever I get time. Your content is really amazing.
A question if I put a 100uf 100v capacitor nothing happens to it, or something harmful in the module
in the throttle side do i need to move the joystick backwards for reverse (i want to make a car)
edit : also how do i make it 6 channel
Hearty and Rugged AF!! Nce work!
Hello sir , Thankyou so much for sharing this video,
By the way how do I calibrate the ESC if i am using a bldc motor ?
congratulations!! great project. have you ever check total range about this project ??
Thanks. About 70-80 meters .. th-cam.com/video/9SMyBN-B3Vo/w-d-xo.html
Öncelikle merhaba size bir sorum olucaktı.Bu uçağın üstüne bir adet daha servo eklemek istersek bunu kumandadan nasıl kontrol edebiliriz acaba teşekkürler.
I was wondering if this is possible to make using a breadboard instead of tin welding it
I have finished all the connections as per the video and I have connected the battery but I am not getting any movement in the motors . What could be the cause for it?
Hello, very good, the video I wanted to know if the programming is compatible with the video that you uploaded from the dual engine
Thanks for the video very nice project and sharing is good for people that cant do it as well as you 5 star
5 минут "полётов" на таких стиках...останешся без рук. Но в общем идея супер! Лайк полюбому
Hi, which range (m) do you expect outdoor?
Do you think it is reliable enough to fly a model airplane?
Thanks!
My test video for airplane.. th-cam.com/video/9SMyBN-B3Vo/w-d-xo.html
You are using Arduino for controlling and NRF24L01 as wireless module, instead of using 2 components can we use only one component which has both functions for example can we use nodemcu esp8266?
Good project!
What is that rod thing that you connecting with the wires?
Hey I have a question, can you use an Arduino Nano for the transmitter and an Arduino Uno for the receiver?
Yes it is possible.
If i want to cotrol the motor forward and backwards, would i need a motor ic or do i also need another wireless module ? want to build a lego rc kit to control cars and have some additional functions...
(did some arduino projects but never with the wireless modules)
You need a motor driver IC or an ESC.
@@Kendin-Yap Thanks for your reply, and thanks for sharing your project here. I also found that at least some of these wireless modules support up to 6 channels which fits perfectly for my project..
Sir, when I use nrf24l01+PA on receiver, I can't connect (binding) to the transmitter..please help me sir..thank you..
Bro i love you I asked so many in questions in different videos you are the only who replies thank you for your replies and 1 last question.
Can i use two 775 motors with esc and 1 servo and 14v battery.?
Bu kanal aşırı kaliteli
What's the maximum range with this setup?
about 70-80 meters
( FIXED )) Hi I actually made this and for some reason It doesn't seem to be transmitting , when I plug in the battery to the transmitter , it lights up red as normal, and plugging in the receiver makes the servo come to a position and stop, its always a little movement and stops . But when I use the joysticks it doesn't work ( and no leds seem to show that it's receiving data ) wonder what went wrong?. Btw I did exclude the esc and directly connected the positive line to the servos . Maybe that was thr issue ? ( I need to control 4 servos with thus without an esc )and the servos are sg995 ,
Edit : turns out there was a short circuit in the transmitter pins , fixed that and works fine ( best way to check this is try to reupload the code to the arduino and if it doesn't allow you to upload and give you that avr dude error , it's something that could be with a short circuit )
Thanks bro ,it's really works I had tried
bro what is the range of this transmitter and reciever
plz tell fast
Tell bro
70-80 meters
@@Kendin-Yap Thanks bro then which video will u reccomend in which range is above 1 km
i have a question i did it like in the video but there is lightning the tx on the receiver. i am not that deep in electronics but it cant load
the programm on the receiver if the light is blinking do you know how i can fix it or what can be the problem. i built it the third time now and its still not working
I recommend watching my video tutorial on installing the code. You can try to upload it before making any rc-related circuit connections to the arduino. So you can understand whether the problem is with the arduino or with your connections.
th-cam.com/video/f1z8Wvy56t8/w-d-xo.html
@@Kendin-Yap i already watched the tutuorial and i also tryed before the problem but still dont work xD
If you're having trouble uploading to the arduino, it's not about the circuit and the code. There may be a problem with your Arduino. Or there may be a problem with the USB dirver.@@nikeytuqe6515
@@Kendin-YapFirst. Thanks for answering me and help me. I know exactly what the problem is. One wire is the problem. if i connected it i cant upload and the tx is blinking but if i dont connect it it upload and the tx isnt blinking, but it still doesnt work because the wire i am talking about is the on which is connected to the D2 from the arduino and the ESC . I hope you know what wire i mean. Thanks for helping me Paul
hello I can do it with esp8226 because it is cheaper and I put emitter and receiver
Bro ,I am not getting 180 Dc motor of 39000 rpm ,which other one should I use.....
Hey bro ...
How many brushless motors can we control with this module ?
Hey bro..
Thanks for your information ...
Can I use it to make a drone
Hello sir, can you assist. What is the optional for the battery beside the lipo 7.4v 4500mah.. please help.. your video very informative
saludos como conectaste ese motor del controlador de velocidad y puedes acelerarlo pense que solo se podia en motores brushless
Can you give us a lesson on the Quadcopter drone project + the code programation for the transmitter and receiver?