How To Use a Car Generator With Permanent Magnets For Free Energy Projects
ฝัง
- เผยแพร่เมื่อ 26 ก.ย. 2024
- Don’t spend money on expensive generators to use in your windmill or on any hydro electric project to harvest free energy. It can be an old car alternator from your car that’s about to be thrown out. The core of the motor can be modified and permanent magnets can be installed instead to become a permanent magnet generator to harness electrical energy for your house or to store energy in deep cycle batteries for later usage or emergency. Here is one video we made about that subject: • How To Use an Inductio... we might make another video about the same subject. There’s many different types of alternators but one thing to point out is that the core of a car alternator is in sense a single electromagnet with a north and south polarity. Each polarity has 6 individual arms, in this case, there’s six north arms, and six south arms. After the arms are cut off with a grinding wheel, they need to be replaced with permanent magnets instead. They have to alternate north, south, north, south. This is a tutorial on how to convert a car alternator into a magnetic AC generator to generate AC electricity and power different loads. At low RPM, it can produce 12-24 volts AC, but at higher RPM, it can generate 120-240 volts AC. This is a DIY tutorial on a car alternator.
You should do a follow up video where you build a fly wheel to hand crank the generator. And then you could connect it to a battery and charge it.
There is popular video on YT I am sure you guys have seen it, it's very similar to this, they show it self running with an AC motor on belt.
Trick they do is the magnets are "two per pole" and they butt two "lined up" rectangular magnets edge to edge with either NN or SS to the edges so alternating bucking magnetic fields are reacting to the stator coils.
The pairs of magnets want to push each other away so it's the glue that holds them there in place.
Anyways you should try that too, maybe lenz braking reaction when stators load with resistance is not very strong with rotor magnets bucking like this and is possible to loop with an AC motor as load.
There's many scams on YT claiming free energy.
Even this video doesn't make sense he cut out magnets to put in different magnets.
I'm pretty sure he made it less efficient.
But he never does any Power and energy measurements.
Its all just click bait scamming for people who don't have a good understanding of electricity and magnetism.
What epoxy resin did you use? Brand? What percentages did you mix according to your use? Thank you very much.
Where do u get the free energy to power the hand drill?
This is not a free energy project, it's a helper project.
Wind, rivers
The hand drill is to demonstrate what your bicycle, river or wind can do
Brilliant! You just exposed that decades-long scam by posing one simple question! The empire will crumble now! You'll go down in history as the "whistleblower"!
Hey Vance I'm just messing with u dawg! I was just trying to be funny. Dont take offense. I know you're a good sport.
أنا مشترك جديد من العراق واحب اعمالك الرائعة
Daniel, shouldn't the winding be removed from the rotor ? Not like it's doing anything.
Chemical based solutions can cause magnets to lose magnetic - strengths. Don't not submerge in "less understood" reactive coated mixtures. Make solid pvc cut-out slots instead.
Wouldn’t it make sense to put the reverse the polarity of the magnets on the inside? I’m hoping to find a way to create constant movement that’s not driven by any variable other than the initial thrust.
Essential you are transferring electricity from the battery. Still Doesn’t make sense unless those lights are 12v DC. Does the alternator act as a step up? Still clueless where the inverter aspect is
Please, what is the output voltage of pm alternator gives out. Thanks, good job.
The strength of the permanent magnets used and the gap between the permanent magnet and the iron core determines the output of the coils at a certain rpm. The stronger the magnets and the closer the gap, you will get higher voltage and current at very low rpm. We only used a drill to turn the rotor of the generator at low rpm between 5 and 10 turns per second which comes to 300 to 600 rpm that delivers 12 to 24 volts AC. Of course at say 3000 rpm, the voltage output will be between between 120 and 240 volts AC.
Could you believe I have gotten the secret the guy used in YT liberty engine. If the alternator can be made high efficiency, and the rpm of motor and alternator mechanically be the same and constant, then the machine would be self running.
Very cool! Glad I found your channel 😊
I took apart the pole peices and replaced the coil of wire with a magnet and sent power to it from a ebike controller and It would malfunction at times , I think the controller was confused with no Hall sensors and I think was reversing motor direction making the motor vibrate to my amazement it was levitating for a very short time ! I think this is the principal that a "UFO" could use to make it fly. Vibrating magnets at the proper speed. The moter got hot extremely fast , but that's probably like ten pounds to levitate. For maybe two seconds.
I always had an idea as a kid to use magnets to propel vehicles, but you think like the Jetsons?
I hate to say it, but how did you get the energy to charge the battery in the drill? But keep up the good work love the videos. Lol.
errr you need to read the description, he never said that the magnetic engine produces free energy. its simply a design to take the energy FROM a windmill or hydraulic system and convert it into energy. *facepalm*
What if u put magnets around the case of the altenator, will they force it to spin
The title of this video should be "how to make an alternator act as a generator for small DC loads". Where is the free energy in this setup?
Read it again. "to use in your windmill or on any hydro electric project to harvest free energy."
So many negative comments. Once you got these things started (with non-renewable energies) you could power these off of each other. It’s better to set them off with stuff like oil or petrol or whatever but it is a much better idea than using the non-renewables constantly…
Congratulations on the project, could you indicate the power of the magnets in gauss or what type they are n34 or n42 etc.
Use the most powerful magnets available and try not to use too much high rpm or it can explode.
I could only find THOSE magnets in N42 grade --- I'd like to have had N52 available in that size.
What would it do if you put the magnets in but assemble it for car alternator configuration and put it back into car . Would it just make it produce power at lower rpm because it doesn't need excited at high rpm or high 12v volts applied to winding
Magnetic field is controlled by AVR by means of limiting current to the field armature coil depending on the output voltage. But when you fit permanent magnet onto the armature there is no control on the intensity of megnetic flux. So at high RPM, it will damage electrical components in the car.
Slow motor rotation but high current out. follows this method when put the magnet. SSS NNN SSS NNN SSS NNN. The magnet does not need to be very large.
Interesting video! With an alternator, when there is no more current required, the torque resistance stops and the alternator freewheels. With this generator, there never comes a time where there is no resistance. Correct?
The magnets change it from DC power to AC power and does it get hot fast most likely because the law of physics talks about thermal with a self-powered motor
pretty cool, how many volts are you getting at what rpm??
The strength of the permanent magnets used and the gap between the permanent magnet and the iron core determines the output of the coils at a certain rpm. The stronger the magnets and the closer the gap, you will get higher voltage and current at very low rpm. We only used a drill to turn the rotor of the generator at low rpm between 5 and 10 turns per second which comes to 300 to 600 rpm that delivers 12 to 24 volts AC. Of course at say 3000 rpm, the voltage output will be between between 120 and 240 volts AC.
@@DanielsInventions amazing Sir!
Do you have a D.C motor 1CV handy to close the loop?
@@DanielsInventions like the Infinity Generator
@@DanielsInventions But it is a theorical situation, until you test it at that RPM we will beleive it, meanwhile we'll be in doubt because there is no voltmeter involved.
@@DanielsInventions is it reallyy possible to get 220V from a winding that was designed for 14/12V? dozens of other experimentators failed on this one
Already you isolate the magnatics and rotor. What is that materials type you have used to isolate the rotor and magnatics?
Epoxy
You should just put a speaker magnet in there where the electromagnet was. They alredy have hole in the middle
Привет дружище а я б не стал портить полюса а просто на боковини наклеял полюса s n так чтобы за крышки генератора не задивали ну тоже классно получился генератор 👍👍👍
When do you think the store will be open?
Some induction motor generator are possible to generate electricity but probably the windings are not magnet copper wire
On one of Nikola Tesla's patents, it is just another version of an induction motor. He claimed that his motor was over 100% efficient, but it did use a massive amount of copper winding. Nowadays, electric motors are around 80% efficient.
@@DanielsInventions that is awesome and good though
Useless. The electromagnet is much powerful
تحية من العراق
Nice 👍👌
👍
That’s good Why don''t you make it and start selling it?
That was amazing, you make it look so easy, youre farther is a Genius and craftsman of the century, where are the dielectric field levitation devices? i must ask. at this level everything is possible. hi voltage M-state matter devices? and father like son. lol
Makes what look easy.
He didn't measure the power or energy generation before the modification.
But I'm almost positive it would be less efficient.
I’m a keen gardener and I’ve recently found out that magnets can speed up plant growth a d vigour.
WE HAVE BEEN ROBBED OF HARMONIOUS LIVES BY RICH MEN
Warum bekomme ich diese viedeos in einer Fremdsprache in Deutschland ich spreche nur deutsch oder muß ich auch noch Englisch lernen
شعب متزمت تعلم كل اللغات لينا في ألمانيا لترد علينا بالمانيا نعرفكم جيدا متزمتين
Спасибо 👍👍
What is the output voltage at high rpm
Alternators have a voltage regulator, so about 14V ±.3 or so
Mi piacerebbe che fosse spiegato in lingua italiana la cosa per me e interessante grazie
For so long I wonder why so much force is needed to turn a permanent magnet generator and when I release that the iron core is the biggest lie of them all to stop the frequency from equalize with the voltage causing to much resistance in the iron and when I remove 60 % of the iron in my generator I instantly realize that too much iron created too much back emf the iron is the cause I had very little resistance on the generator the voltage was higher and the drag force was not even recognizable and the 6000rpm was just right to break the resistance valve
Dude, it was more effective with rotor winding. You just made it less powerful, less efficient and disposable. If you'll try to get real power with permanent magnets - they will overheat and loose magnetism.
Complete useless DIY.
Todo ese trabajo para sacar solo unos voltios
Daniel, you've watched hidden technology build? Do you see how he is over unity or do you see how it is being done w illusion?
We don't believe that one works. We have a lot of experience building over unity motors and testing free energy patents. After they did their video, they should disassemble the induction motor and the car alternator all in one clip to make sure he doesn't have any hidden batteries in there. Also, he needs to do the experiment out in the middle of nowhere where there is no access of electricity nearby.
I recall one clip where they disassembled the motor, dont recall if it was unbroken. They do have a 2 hr vid of it running, supposedly continuous. Im not a video expert though.
@@johnM-Jr This dude copy liberty. He just does not have the same resources to spend another couple hundred on an AC motor.
The first one of their videos I saw looked like it was plausible but didn't include enough detail to know for sure, but then I checked another video on their channel and it was an obvious scam, so I wrote off their channel as scammers.
N aur s ka nisaan kiu lagate hai
Creative video,thanks :)
And now Use IT With the magnetic Rotors that U used to get IT moving
how you connect the 4 wires to 2 wires? sketch it please
There's many different alternators, this one has 4 wires. Each wire to ground gives a certain output. If you use the first and last, you will get the most voltage out because all of the coils are interconnected together. That might not be the case for different kinds of alternators.
2 ALTELNATORY...ZNIČENÉ...,12 MAGNETOV!...
A PRD!...
ČIŽE PODVOD!!!
End product looks way too heavy.
And I didn't care for that metallic vibe it gave off!
Tv,AC,water pump ,.....
Was wird es?
Scusa... ma a che cazzo serve? A rovinare gli alternatori? Guarda che funzionano lostesso anche senza sfasciarli... basta farli girare. Che cazzo di video...mah..
*DON'T LIE ANYMORE, IT WILL NEVER WORK*
Gratulacje, zmniejszenia sprawności z 60% do 8%.
Wlasne, ale to DIY :D
A zrobiłeś i wypróbowałeś?-pajacu.
Jak juz to rozdzieszasz pazury i zamiast cewki wkladasz magnesy neodymowe... potem z powrotem sprasowujesz.
⚠️SCAM⚠️ Saw early on this channel was slowing introducing scam vids as a means to make big money. Now dad has corrupted his son. Sad what this channel has become. By no means is this free energy. Their magnet motors are also a scam.
wow you are some different kind of stupid aren't you? "to USE in your WINDMILL or on any HYDRO ELECTRIC PROJECT to HARVEST free energy." holy shit man, how you people come from a lineage of survived male procreators is honestly astonishing to me.
Free ?