You have the best video on how to do this and the best results I’ve seen from countless videos. You do steps that I haven’t seen from others and the results speak for themselves.
I don’t know why no one is backing you there must be businesses out there that like what you’re doing & are willing to sponsor you. Keep up the good work I’ll be watching👍🏾
Very impressive for your first time. Thought you were doing a vinyl wrap at first so was very surprised and excited to see it was a no shit weave! Would have liked to see a bit more of the process though.
I wrapped my trim with cf but i didnt sand it. Definitely looks more finished after what you did. Can you do more of these videos? maybe one for the mirror caps?
Truth! Nothing ever does go as planned, and the Baby always come first. I have a small rule that I don't work on my cars unless the family is away or they're in the garage with me spending time together. Sub'd and I can't wait to watch the rest of your videos.
Hey buddy, just letting you know. I'm about to start my own CF project following this DIY. Love your content. Good stuff man. I even purchased the same resin you did. If my results are half as good as yours I'll be happy. Lol
Yooo boss man! Remember you did lowering on the stinger right, you know the gunmetal chrome trims like grill and mirror caps. So if I wanted to do this I would have to sand them too right, to create better adhesion
How many layers of epoxy did you do on the trims before adding 2K clear coat? In the video you showed two coats of epoxy. Did you do more than two? If so did you have to sand it down every time, clean it up, then re coat it and wait 3-4 hours?
Hi, great work. im also do skinning. and all the videos i saw ,they use the epoxy for base coat. i had many issues with it.cuz the carbon lifts up. im going to try your method, with the 3m. so u just spray the part put the carbon , and then right away put the epoxy on it? no need to wait for it to dry? also did u sand the part before putting the 3m spray? thank you
That hexagon carbon fiber looks really good. How did you do the ashtray so the pattern on it matches the pattern on the centre console, that is to say the pattern flows from the console to the ashtray?
Hey man good job. Did you buy carbon fiber twill ? How much does it cost for a roll. I noticed your from Canada, so is there a local distributor you would recommend?
Question: if i buy unpainted rear spoiler for my 550 F10. Can i place the carbon fiber on to it as u did these trim. Also i was thinking abt side skirts and front bumper lip so all pieces can look sync. That means i would have to possibly redon my rear diffuser. Please help. Thanks
@@FATmods I’d like to get center trim done the one where the stick shift is. Also probably the doors trims as well. Maybe center one that vents run thru
@@FATmods yes I realized I put too much epoxy or wtv but also how many layers of epoxy did u use before sanding and did u use that sponge for all of the layers or just some
You have the best video on how to do this and the best results I’ve seen from countless videos. You do steps that I haven’t seen from others and the results speak for themselves.
Glad I could help
I don’t know why no one is backing you there must be businesses out there that like what you’re doing & are willing to sponsor you. Keep up the good work I’ll be watching👍🏾
I don't have enough views and subscribers so no one will sponsor me. Thanks for the support
Real talk if he came to Los Angeles he would be popping
FROM ZERO TO PRO BRO. I LIKE YOU. I TRAINING CARBON FIBER 2 WEEKS. AND NOW I HAVE SHOP CARBON FIBER SKINNING FOR MOTORCYCLE❤
👍 congrats
Looks amazing. I'm doing carbon fiber overlay for a few months. I love using the West System epoxy, pumps make it so easy. Good job man
Thanks.
You got a like from me for the first min of this video. A real man with real priorities
🤣🤣👍
F.A.T mods and because you replied you get a sub. Keep it up bro
👍I reply to every comment
That looks good brotha!!thanks for the DIY, looks professional keep the video coming!
Thanks and I will try
Very impressive for your first time. Thought you were doing a vinyl wrap at first so was very surprised and excited to see it was a no shit weave! Would have liked to see a bit more of the process though.
I wanted to bit the video would be too long. I will show more when I do the roof
Another dope video
Respect
Holy shit that looks gooooood!!
Thanks
That looks absolutely amazing!!!
Thanks
looks incredible brah! aces!
Lol thanks
That looks awsome. keep up the great work.
Thanks I will try
I wrapped my trim with cf but i didnt sand it. Definitely looks more finished after what you did.
Can you do more of these videos? maybe one for the mirror caps?
Ok I will see what I can do
You do Really Great work!! Thank you for sharing 😁❤
👍🏾👍🏾
Big up yard man. That looks amazing. i was doing 2x2 twill but that honey comb carbon looks a different level.
Thanks. I wanted something different
Nice job, I will be trying my take on carbon fiber soon and post on my channel. Liked.
Looks Awesome! Good Job!!!
👍👍
Truth! Nothing ever does go as planned, and the Baby always come first. I have a small rule that I don't work on my cars unless the family is away or they're in the garage with me spending time together. Sub'd and I can't wait to watch the rest of your videos.
Yeah they come first. Thanks for the support
Beautifully done bro!... you just gave me the confidence to do it myself......L will be needing your guidance
😂😂 anything I can do to help
Man it turn out real clean! Keep up the great work
Thanks and I will
It came out really good. Nice job 😊💪🏻
👍
Mannnnn that looks sooo Good!!!👍🏿🔥
Thanks man
👍🏾👍🏾
Love the build bro
Looks amazing bro! Thanks for all the tips now. Gonna cf my is300 wagon now
Glad I could help
Absolutely amazing work!
Thank you
Looking forward to seeing you do it on your F10. Good video brotha.
Thanks
Wow the honeycomb looks amazing. Great job neighbour.
Thanks neighbor
Are you working on it today?
All day
I work all day today no time for the car 😭😭
F.A.T mods to ok kool. Would love to pop by to have a look at what your doing. Some day.
Nicely Done.
This looks amazing. Keep it up bro!
👍
They look awesome 👍 Great job
Thanks
wow i never even thought about just wrapping carbon fiber unto the trim rather than buying a whole new trim piece
😂😂 glad I could help
Look amazing. Beautiful brother 👍🏻👍🏻
Thanks
Looks sweet man, skinning my e82 interior tomorrow.
I love doing stuff like this
Nice work
Love your video you got a new subscriber now I feel confident tackling a carbon fiber project!!
Where did you buy your carbon fiber from?
Thanks and all from ebay
That looks great bro
Great job man.
👍🏾👍🏾
Hey buddy, just letting you know. I'm about to start my own CF project following this DIY. Love your content. Good stuff man. I even purchased the same resin you did. If my results are half as good as yours I'll be happy. Lol
just go slowly and it will turn out great
love the vids man!
Thanks
Holy..... this looks amazing. How did you do the doors? riped the leather off and skinned over it?
Skinned over it
Really good results! Amazing work 🔥
Thanks 👍
Fantastic content, cant wait try on my r34
👍🏾👍🏾
Good job man 🤝
👍🏾👍🏾
That looks great. I'm thinking of doing this my car's front splitter.
You should
Yardie that looks fire🔥
Thanks
Dang I seen this design and thought it was ugly but you made it look good
🤣🤣 thanks
Looks sick bro! How long did this take you to finish?
About a week
You have a long Canadian winter a head to get these part of the car completed. Use the current seats you have and see what you can make with them.
Yooo boss man!
Remember you did lowering on the stinger right, you know the gunmetal chrome trims like grill and mirror caps.
So if I wanted to do this I would have to sand them too right, to create better adhesion
Just rough it up wit 80 or 40 grit
How many layers of epoxy did you do on the trims before adding 2K clear coat? In the video you showed two coats of epoxy. Did you do more than two? If so did you have to sand it down every time, clean it up, then re coat it and wait 3-4 hours?
It all depends on how much you sand off. I do probably 5 layers
Awesome... Where to get the honeycomb carbon fiber sheets???
Ebay
OMG!!!!! Honeycomb looks freaking SICK! You have a link for where you get the materials for your project?
Everything off Ebay
what did you do after sandin did you put a clear coat then do another wet sand ?
Link to that honeycomb carbon fiber?
You did great job sir . How did you remove bubbles from epoxy resin ?
There were not. I use west system. If you use heat gun you can get rid of bubbles
Soooooo soooo sickkkk bruhhh what if I send my trim pieces to you for honeycomb carbon fiber how much would u charge or would u do it ???
For what car
Thanks very much. Why do some guys doing this say you have to put the piece in a vacuum bag and others not?
It make it smooth and easier to sand but you dont have to
Looks great man! Where did you get the honeycomb wrap from? I'm in Calgary and struggling to find in Canada.
Ebay.com or alibaba
Hi, great work. im also do skinning. and all the videos i saw ,they use the epoxy for base coat. i had many issues with it.cuz the carbon lifts up. im going to try your method, with the 3m.
so u just spray the part put the carbon , and then right away put the epoxy on it? no need to wait for it to dry? also did u sand the part before putting the 3m spray?
thank you
You sand wot 120 or 240 the spray both pieces and wait a few minutes. Use the 3M90
@@FATmods o.k i will use the 3m 90.
i hope that will fix the carbon from lifting. the 3m 90 is better?
I have the same problem when I use the epoxy
cool. i will try it with the 3m 90 . and also i will coat it, with the west system epoxy 205 and 207. what ratio do u do? 3:1?
It comes with the pump so it 1 pump of each
That hexagon carbon fiber looks really good. How did you do the ashtray so the pattern on it matches the pattern on the centre console, that is to say the pattern flows from the console to the ashtray?
I just match it up with a small piece
@@FATmods Perfect thanks! I have ordered the bits so I can do the interior of my BMW, I am both nervous and excited at the same time. LOL
And questions link me on Instagram
Hey man good job.
Did you buy carbon fiber twill ? How much does it cost for a roll. I noticed your from Canada, so is there a local distributor you would recommend?
I bought off ebay and honeycomb does not come 2x2, it's just honeycomb and I only bought what I need.
Hey man do you have a link to the apoxy and the honey comb carbon?
bro what did you used in the end to make it clear as that , have you used UV Top Coat ? or what, please let me know
I use 2k clear
Good job
👍👍
Great job man. Can I use the same methods for forged carbon fiber! Thanks a lot man
Thanks and I think so
F.A.T mods appreciate your reply, I’ll start ordering stuff and will see how it goes. Again Appreciate it man
Great job. Where can I get that ccarbon fiber
Ebay
Thanks for the video! The website says 3:1 ratio, want to confirm it is 1:1?
If you get the pumps it mixes 3:1 in the pump. So 1 pump of each
Did u clear coat after every layer or just after all the layers
You clear coat when your final layer of resin is done and all sanded
Looks damn good
Lol I guess old people have use
@@FATmods sometimes... Can't use em to spell though
Do u have the link on where u found the tools and wrap?!??!??
What tools, just search honeycomb carbon fiber fabric
Hello, what brand are the materials used?
Question: if i buy unpainted rear spoiler for my 550 F10. Can i place the carbon fiber on to it as u did these trim. Also i was thinking abt side skirts and front bumper lip so all pieces can look sync. That means i would have to possibly redon my rear diffuser. Please help. Thanks
This is not a wrap you can't stretch it. If the piece doesn't have a lot of angles you could do it.
looks great! where can i purchase the wrap?
It's real carbon fiber not a wrap and you can get it on ebay or alibaba
So insane cant believe you did it in your garage
I couldn't find it so I did it
F.A.T mods of course it looks so great i want some for my volvo
Lol I did
Gonna look dope in my jeep 😜
🤣
🤣🤣
respect little ones come before everything 💪
Yes sir they are way more important
@@FATmods good job on the trims also man looks fantastic brother 💪 definitely gave me motivation to do it my self, be safe and blessings .
Thanks and blessings to you to
where did you get that honey comb sheat? and the link to the rest of the materials
All on ebay
Did you wet sand after the final resin and are they clear coated or polished?
I just dry sand wet sanding only keep the dust down. I clear coat with 2k clear
@@FATmodsIs there a 2K clear that you recommend?
Spray max 2k
How did you get the air bubbles out?
The epoxy I used did have aur bubbles
What’s the total cost to do this diy?
I don't know. The cost for carbon fiber and epoxy. I already had it in stock.
where did you buy the carbon fiber and what grade is it?
Ebay 2x2 Twil
Where did u get ur sand paper
Any paint supply store
love for you make new updated video :)
What do you mean what's the last video you seen. The car is finished
How much will you charge me to do my trim man
No idea it very labour intensive
Link me in Instagram
👍🏾
u gotta be Jamaican lol im doing the same thing and ah run from the same tings
🤣🤣
Beautiful job!!!! You can do mine to?
Sure
F.A.T mods friend request FB antonios anastasopoulos
💯💯💯💯💯💯💯💯💯
4🤣🤣👍🏾
@@FATmods ...You're one of my favorite channels mane keep up the good work Bro. I'm trying to hook my X5 up as well...
holy...
🤣
Beautiful!
What’s your insta ?
F.a.t_mods
What's the song @ 10:12???
So I found the song Southside but I need the exact version please
I’ll pay you to do some work for me? If you’re interested?
What u need done
@@FATmods I’d like to get center trim done the one where the stick shift is. Also probably the doors trims as well. Maybe center one that vents run thru
the method looked a lil ghetto to be honest working on the ground, but the end result is very cool.
dont knock it, the results speak for itself.
What is the spray?
3m 77 but you can just put the Epoxy on and wait till it gets really tacky
Did u ceramic coat it at all cuz I did mine but when I touch it it kinda gives it a finger stain
Mine is hard. Did you clear coat
@@FATmods yes I realized I put too much epoxy or wtv but also how many layers of epoxy did u use before sanding and did u use that sponge for all of the layers or just some
At least 3 and what sponge
@@FATmods like the sponge brush thing