It doesn`t hurt opening the butterfly. When you have cleaned the butterfly and throttle body you have to run a re-learning program on the throttle body using a scan tool. So the electronic actuator resets its position anyway.
Why not diconnect the coolant fluid tube on the throttle body side rather than deeper down? That lower one seems harder to get to when the one right on the body was right there.
2008, never cleaned. Wonder if this is why my car is so hesitant to take off when the AC is on. Have done the spark plugs, coil packs, air filter and used Lucas fuel injector cleaner, but no solution so far.
Yea mine has a little hesitation when AC is on... But when off my car is still a rocket ship with 200k. I just cleaned my throat body. I even use a K&N filter in factory airbox. I guess it helps . I will buy new PCV assembly & Mass Airflow...
This looks so easy yet difficult lol. I have a 2008 mazda 6. And it stays right under the 1 when turning the car on. I rev it and it will never go any lower. The line stays under 1. Never at 0. Is that bad ? Will cleaning just the front valve part be more than enough or do I have to take the whole thing off. And deep clean ?
I took cleaned the throttle body on my 2007 mazda 6 I and now I hear a ticking noise coming from my car. Is that normal. Also could you do a video on how to replace an egr valve on a 2007 mazda 6 I. I took mine off to clean it and now it's leaking radiator fluid from the bottom of it.
Hey you guys drained the coolant when replacing the throttle body but not for cleaning the throttle body ? Is it ok to not drain when cleaning ? Thanks
I did all the steps shown in the video. Took the hoses off took the screws out and when I tried to pull the throttle body off it won't come off it's like it's stuck. I don't know what to do?
There is a humming/buzz noise coming from my throttle body unit... car will not turn over completely. Every few hours it will turn over and run for approximately 3 seconds then kill... should I replace throttle body completely or try cleaning 1st.
+Kevin Reed While we cannot give you a definitive way to move forward, cleaning this would be our first step to avoid replacing a part that is bot defective, just needs a little cleaning. If you are still experiencing the issue we would recommend taking this to be properly inspected to ensure the correct part is replaced.
It is recommended that before removing the throttle, you disconnect a ground from your accu. After cleaning and putting back the throttle body you connect the ground clamp. When you start the engine ECU will accomodate the throttle for about 20 minutes. You shall not drive during this step.
I'm AJ thank you for helping me now I know how to change my throttle body but I just was wondering that when you took the trailer body thing off you didn't mention anything about the seal then when you was cleaning to try to bother you good point about not moving about a fly secondly you started cleaning with the same brush that automatic had the residue on it and then you left a big spot of the residue on the butterfly but that's understandable but that seal is very important to let a person know that the seal comes off when you take it off but you didn't mention it when you're first took it all but you meant you you put it back on after you resemble it for some people should know how very important that is because if you damage it in some kind of way you got another problem I'm just giving you a heads up lady you did a great job thank you for showing me how to do that and I was wondering it's a silver radiator that says on top of the motor do I have to take that off too I didn't see it on on the video when you was doing the The Squatty body throttle body but anyway nice job you go girl from AJ take my head off to you you want to send me a comment I still appreciate it great job lol AJ God bless bye
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
This lady has taught me a lot about cars.
I've been able to get over a lot of things that I was intimidated by.
Never too old to learn something new.
glad i watched this video before making any moves. There are a BUNCH of videos of people forcing open that butterfly valve
+HIGHERWØRLDS PRODCTION Thanks for checking us out! 1AAuto.com
It doesn`t hurt opening the butterfly. When you have cleaned the butterfly and throttle body you have to run a re-learning program on the throttle body using a scan tool. So the electronic actuator resets its position anyway.
Why not diconnect the coolant fluid tube on the throttle body side rather than deeper down? That lower one seems harder to get to when the one right on the body was right there.
2008, never cleaned. Wonder if this is why my car is so hesitant to take off when the AC is on. Have done the spark plugs, coil packs, air filter and used Lucas fuel injector cleaner, but no solution so far.
Yea mine has a little hesitation when AC is on... But when off my car is still a rocket ship with 200k. I just cleaned my throat body. I even use a K&N filter in factory airbox. I guess it helps . I will buy new PCV assembly & Mass Airflow...
i thnik the TB willl reset calibrate after cleaning.
How big of a catch pan is needed? Will the entire amount draing out? Should I plug the fluid line with a bolt?
This looks so easy yet difficult lol. I have a 2008 mazda 6. And it stays right under the 1 when turning the car on. I rev it and it will never go any lower. The line stays under 1. Never at 0. Is that bad ? Will cleaning just the front valve part be more than enough or do I have to take the whole thing off. And deep clean ?
are you talking about your rpm’s man, if so they definitely are not supposed to drop lower than 750
1=1000
Super helpful tutorial. Much appreciated.
I took cleaned the throttle body on my 2007 mazda 6 I and now I hear a ticking noise coming from my car. Is that normal. Also could you do a video on how to replace an egr valve on a 2007 mazda 6 I. I took mine off to clean it and now it's leaking radiator fluid from the bottom of it.
Im hoping this fixes the gas pedal shake when my ac is blasting
I want Sue as my neighbour 👍
Can’t you reset the throttle body closing position after cleaning it if you also open it?
I was wondering the same thing. Seems CLOSED would be home poisition.
Hey you guys drained the coolant when replacing the throttle body but not for cleaning the throttle body ? Is it ok to not drain when cleaning ? Thanks
I did all the steps shown in the video. Took the hoses off took the screws out and when I tried to pull the throttle body off it won't come off it's like it's stuck. I don't know what to do?
Does mazda 3 diesel 1.6 have Throttle Body? I know some diesel have it.
Hi, Do you have the same one on mazda 3 2006? I have mazda 3 2006 and it's not look the same
Should I disconnect the battery first?
That a 4 cylinder? Bc mine looks nothing like that
More videos on Mazda 6 2.3L i THANK YOU
+TRUTH SEEKER Thank you for your feedback! We are always creating new videos so check again soon!
I should've seen this video before I cleaned my throttle body. I opened the plate with my hand and now the car accelerates by itself :-(
Can it be fix?
I did the same thing. 😒
Lol
Lol
There is a humming/buzz noise coming from my throttle body unit... car will not turn over completely. Every few hours it will turn over and run for approximately 3 seconds then kill... should I replace throttle body completely or try cleaning 1st.
+Kevin Reed While we cannot give you a definitive way to move forward, cleaning this would be our first step to avoid replacing a part that is bot defective, just needs a little cleaning. If you are still experiencing the issue we would recommend taking this to be properly inspected to ensure the correct part is replaced.
did u ever figure it out?
why is the battery disconnected
Is there no need to reset the throttle body after having it disconnected?
It is recommended that before removing the throttle, you disconnect a ground from your accu. After cleaning and putting back the throttle body you connect the ground clamp. When you start the engine ECU will accomodate the throttle for about 20 minutes. You shall not drive during this step.
I'm AJ thank you for helping me now I know how to change my throttle body but I just was wondering that when you took the trailer body thing off you didn't mention anything about the seal then when you was cleaning to try to bother you good point about not moving about a fly secondly you started cleaning with the same brush that automatic had the residue on it and then you left a big spot of the residue on the butterfly but that's understandable but that seal is very important to let a person know that the seal comes off when you take it off but you didn't mention it when you're first took it all but you meant you you put it back on after you resemble it for some people should know how very important that is because if you damage it in some kind of way you got another problem I'm just giving you a heads up lady you did a great job thank you for showing me how to do that and I was wondering it's a silver radiator that says on top of the motor do I have to take that off too I didn't see it on on the video when you was doing the The Squatty body throttle body but anyway nice job you go girl from AJ take my head off to you you want to send me a comment I still appreciate it great job lol AJ God bless bye
That motor is in desperate need of an oil catch can 😳
excellent, saludos desde colombia
Köszönöm kedves Lady, many thanks again, the cleen throtly is importans for leerlauf!!idle
Did you have to drain the coolant?
+Andres Delavega It does not have to be drained, but you do need to bleed the cooling system any time a hose is removed. Thanks for the question.
"How To Clean Throttle Body 02-07 Mazda 6" Which ENGINE? ;-) I know pretty much the same but which ENGINE?
Very nice. Thank you
this is different from my 2006 mazda 6 2.0di(89kw). this is a 2.3L maybe
101 in/lbs or 8.42 ft/lbs
+A. Lumberjack 101 in-lb.
12Nm, easy..
Thanks
Thanks. Doing the same thing to my mazda6 this weekend.