Definitely an awesome upgrade, but swapping the light bulb for the map light was a pain in the ass. I recommend removing the map light lens and replace it through that method. I used two box cutters to remove lens and a plier to remove the bulb and also use it as leverage when inserting the new replacement by gripping the edges. Hope this helps!
This is a great upgrade but the 2018-2019 version has an LED trunk already. Also the map light housing is different on an 18-19. Do not pull down on it like this. You will break the double sided tabs. Also you can do the glove box without having to remove that entire assembly. A pry tool behind the bulb will bring it out and then you just replace.
I concur with every single point here. I experienced all of this on my 2018 GT. For the map housing, pressing the side clips in with a small flat head screwdriver helped a lot. I pulled it down just enough to be able to see those clips. Also had to stretch them back out before putting the housing back to make it fit tight again. I did use Bill's method for the vanity lights though.
Yeah just did my map, vanity and glove box lights. If I didn’t see those tabs I probably would’ve messed up the map lights and for the trunk light I watched three different videos because I didn’t see a bulb in there to remove, just the led board. If I didn’t see these comments, my trunk would’ve been lightless
If you got a 2018 + mustang don’t use this method to remove your map housing, the clips have to be pressed by a screw driver and you’ll be able to release both sides and the trunk has LED’s already so don’t worry messing with the trunk light
Prying the housing out for the glove box light in the 2016 the plunger assembly doesn’t come out as a separate piece as he shows in 3:00 it comes out in PIECES that don’t easily go back. Recommend trying to remove bulb without removing housing.
little tip cause you got super lucky its hard to to get that off so I'd suggest prying down the housing a little and look inside and push the clips in to release the clasp that's the only way to get the housing off without damaging it if it doesn't come off right away.
Little shimmy my ass. My damn finger are red and hurt! And still didn’t get it to come down! 😩 I have a pry kit but it’s in my other car that’s been in shop getting painted 🥺
The installation of the dome/map lights is incorrect here. It's much easier to just remove the lens rather than the entire part. It's been proven that once the entire part is reinstalled it won't fit snug as it did before
I tried this and being very careful, the socket ended up pushing through. I ended up having to remove the housing anyway. The socket didn't seem like it was very secure.
Thanks! The bulb wouldn’t fit in the socket when I removed the housing. Removing the dome housing was a big pain! Removing the lens is way easier ! A small pick is a must
I changed my lights in the visiors and glove box They not working and the trunk light not working. The trunk light was working before I changed the visiors.
Everyone having trouble with the map lights which I did in 2 minutes but I can't figure out how to do the trunk!! I used my whole weight pulling to the passenger side and it doesn't budge at all, don't want to break the thing
Has anyone swapped the globes in the door lock buttons, window switches, gear selector, main console buttons and steering wheel buttons. These do not change with the colour setting option
@4kGaming Channel I finally got one side down...I think I almost broke it. Good thing I have small hands, I was able to do both bulbs just with the left side off.
@@GregtheAwesomeNinja yeah mine is too but I think ford has some adhesive where it's sits on because when I took mine of dry glue fell and I notice glue on the boundaries. What did you do?
@@umairejaz6665 to be honest it also could just be the plastic bending a little, since I’ve done it and it’s been a while I believe the shape has retaken or something because it feels a lot better now!
The light in the glove compartment is not as easy as you make it seem. I was able to remove the hosing and replace the light but it is a b!tch to try and align back up. There are slots inside the housing that need to line up. I left it hanging until I try it again. Thanks anyways.
@@Letuscheese im heading to autoparts and buying a 10a blade fuse. I think ours blew and its why we aint getting light. This is located in the passenger fuse box (located at the bottom right corner of passenger side, fuse#1).
I like how it’s always looks easy to pull but it’s not than anytime you do anything the clips break on the actually housing or what not so than it’s never the same and to fix it you Gata buy a new house 🙄😂
The video shows him using a small bladed screwdriver. Do yourself a favor and go get some chopsticks from a Chinese buffet and shape the end to match your screwdriver. They're made of wood or bamboo, so you won't accidentally blow the fuse.
That moment when you install the vanity mirror lights and you break off the little POS plastic piece on the back of the cover so now the switch in the visor doesn’t actuate the lights
Have the white version really makes the interior feel more modern.
My friend camaro interior lights made me become jealous of the leds
Definitely going to get.. just got my 2019 mustang and it needs it
Yellow makes it look old. Good thing I found this video
Definitely an awesome upgrade, but swapping the light bulb for the map light was a pain in the ass. I recommend removing the map light lens and replace it through that method. I used two box cutters to remove lens and a plier to remove the bulb and also use it as leverage when inserting the new replacement by gripping the edges. Hope this helps!
This is a great upgrade but the 2018-2019 version has an LED trunk already. Also the map light housing is different on an 18-19. Do not pull down on it like this. You will break the double sided tabs. Also you can do the glove box without having to remove that entire assembly. A pry tool behind the bulb will bring it out and then you just replace.
I concur with every single point here. I experienced all of this on my 2018 GT. For the map housing, pressing the side clips in with a small flat head screwdriver helped a lot. I pulled it down just enough to be able to see those clips. Also had to stretch them back out before putting the housing back to make it fit tight again. I did use Bill's method for the vanity lights though.
Yeah just did my map, vanity and glove box lights. If I didn’t see those tabs I probably would’ve messed up the map lights and for the trunk light I watched three different videos because I didn’t see a bulb in there to remove, just the led board. If I didn’t see these comments, my trunk would’ve been lightless
Man, I just fucked up my map assembly
raydog1111 I broke mine smh 🤦🏽♂️
Alberto Bahena sorry :(, did you try to pull down on an 18-20?
You make that shimey look so easy
I just got these in the mail. Thanks for taking the time to make a video. You guys rock
Our pleasure!
If you got a 2018 + mustang don’t use this method to remove your map housing, the clips have to be pressed by a screw driver and you’ll be able to release both sides and the trunk has LED’s already so don’t worry messing with the trunk light
TryHard760 I broke my overhead console housing clips 😭
Any videos on how to do that? I'm struggling on my 2019 lol. Appreciate the comment, I look like a complete idiot right now
Rajesh Ramsaroop be careful, it cost me 300 to order a whole new console
@@beat2190 damn man that sucks! I'm just gonna do the dome lights as they get used the most.
Too late 😢
Prying the housing out for the glove box light in the 2016 the plunger assembly doesn’t come out as a separate piece as he shows in 3:00 it comes out in PIECES that don’t easily go back. Recommend trying to remove bulb without removing housing.
Thank you. Actively doing this rn
little tip cause you got super lucky its hard to to get that off so I'd suggest prying down the housing a little and look inside and push the clips in to release the clasp that's the only way to get the housing off without damaging it if it doesn't come off right away.
Thank you Bill I just changed looks amazing
Did what he told me to with the middle console light... a little shimmy broke both of my clips lmaooo
Little shimmy my ass. My damn finger are red and hurt! And still didn’t get it to come down! 😩 I have a pry kit but it’s in my other car that’s been in shop getting painted 🥺
The installation of the dome/map lights is incorrect here. It's much easier to just remove the lens rather than the entire part. It's been proven that once the entire part is reinstalled it won't fit snug as it did before
I tried this and being very careful, the socket ended up pushing through. I ended up having to remove the housing anyway. The socket didn't seem like it was very secure.
@@transparent1608 I used a very small and thin fingernail file. Just used the tip and pulled down and the lens came down and off
Thanks! The bulb wouldn’t fit in the socket when I removed the housing. Removing the dome housing was a big pain! Removing the lens is way easier ! A small pick is a must
@@gabrielram9795 should make a video or are there any links ?
I have a premium v6, 2013 mustang. Do you sale LED lighting kits for this year/model?
The plastic covers on the lights are very hard to get off without scratching or denting the plastic around it.
I changed my lights in the visiors and glove box
They not working and the trunk light not working. The trunk light was working before I changed the visiors.
Take the bulbs out, and turn them 180 degrees, and reinstall.
What about the light under the arm rest?
Everyone having trouble with the map lights which I did in 2 minutes but I can't figure out how to do the trunk!! I used my whole weight pulling to the passenger side and it doesn't budge at all, don't want to break the thing
Bro same!! Haha this shts not budging
I’m having the same
Problem also
Try it with a flat head! There’s a little clip push it in and u should be good
Great instructions...thank you.
Has anyone swapped the globes in the door lock buttons, window switches, gear selector, main console buttons and steering wheel buttons. These do not change with the colour setting option
I have a 2020 Mustang and can't get the map light housing off. I'm afraid I'm going to break something if I keep pulling on it.
@4kGaming Channel I finally got one side down...I think I almost broke it. Good thing I have small hands, I was able to do both bulbs just with the left side off.
@4kGaming Channel We do what we can lol
Appreciate it helped alot
I cannot get that done light off. I feel like I'm going to break it...!
I just absolutely sent it I think it’s looser then it was before but worth it??
@@GregtheAwesomeNinja yeah mine is too but I think ford has some adhesive where it's sits on because when I took mine of dry glue fell and I notice glue on the boundaries. What did you do?
@@umairejaz6665 to be honest it also could just be the plastic bending a little, since I’ve done it and it’s been a while I believe the shape has retaken or something because it feels a lot better now!
Where can I get this for 2008 mustang gt all the same light please lmk
Can’t pull off my some light feels like it’ll snap more than it’ll just pop out
The light in the glove compartment is not as easy as you make it seem. I was able to remove the hosing and replace the light but it is a b!tch to try and align back up. There are slots inside the housing that need to line up. I left it hanging until I try it again. Thanks anyways.
Do you have this for the focus rs?
Once installed the vanity, glove box and trunk light stopped working. I read it could be a blown fuse. How do i go about fixing this?
Having the same issue. Only the map lights work for me
@@Letuscheese im heading to autoparts and buying a 10a blade fuse. I think ours blew and its why we aint getting light. This is located in the passenger fuse box (located at the bottom right corner of passenger side, fuse#1).
jp_shelby lmao bro I’m in the autozone parking lot right now as you commented and I fixed it 👌🏽 that fuse is the problem
@@Letuscheese did it fix all the lights?
The trunk light keeps blowing my fuse. Calling diode dynamics to resolve this
When changing the glove box I installed it back perfectly and the light won’t go off. It looks like it’s not hitting the push in tab
Same
Same here! Except the light won't turn on now
What about Center console?!?!
Why is designed that its so hard to remove and install a new bulb. These engineers really wanted to make u work for it😅
it’s not this easy. the lightbulbs do not come out of the map lights
I like how it’s always looks easy to pull but it’s not than anytime you do anything the clips break on the actually housing or what not so than it’s never the same and to fix it you Gata buy a new house 🙄😂
The video shows him using a small bladed screwdriver. Do yourself a favor and go get some chopsticks from a Chinese buffet and shape the end to match your screwdriver. They're made of wood or bamboo, so you won't accidentally blow the fuse.
That moment when you install the vanity mirror lights and you break off the little POS plastic piece on the back of the cover so now the switch in the visor doesn’t actuate the lights
Too blue for me.
Don’t do the dome light like this. Pry it out with a small screwdriver. Mych easier
how to replace your stock bulbs with useless blue led lol. white looks best
;D
:D