DIY EASY EGR VALVE REMOVAL & CLEANING GUIDE FOR NISSAN NAVARA NP300
ฝัง
- เผยแพร่เมื่อ 19 พ.ค. 2021
- Here's a quick guide on removing a Nissan Navara EGR valve and how to clean it as well. Leave a comment below for any questions and I'll try to reply as soon as I can. Help us grow our channel by hitting the SUBSCRIBE button.
Follow us on Instagram @ / btdgarage - ยานยนต์และพาหนะ
![[LIVE] : ONE ลุมพินี 73 วันนี้!! คู่เอก "วรพล vs พันฤทธิ์"](http://i.ytimg.com/vi/rrOljlqse3A/mqdefault.jpg)
![[Live] : ONE FIGHT NIGHT 24 วันนี้!! “จาร์เร็ด vs กุสตาโว”](http://i.ytimg.com/vi/ENNA-fsT67c/mqdefault.jpg)
Salamat sa video sir. Detailed but concise and easy to follow. More videos pa po 😊. Sana lahat ng diy videos katulad ng gawa nyo
Thank you! :)
Thanks so much I've paid $4000 for injectors, $1500 for ERG pipe it turned out to be the ERG valve and not one of the nitwit aussie mechanics picked it - you video is excellent
Thanks! Hope your car is fine now 😊
What were the symptoms? Injectors noisy?
I was wrong wasn't the ERG it was the metering valve ended up trading it in as is - the symptoms where a ferocious knocking like the engine was going to explode - did that for a bit, i.e. - when driving if you lugged the engine in higher gears it didn't happen so much - until turned off because it was frightening - also at times just would not fire kept turning g over with no ignitioyou are.n - then when left fro a few days it was like new ran perfectly - I suspect a couple of mechanics knew what it was and kept milking out - the shame is one was a premier5 Nissan deaslershisop - also sincere apologies to Aussie mechanics - one u8tube mechanic actually made a video about the importance of metering valves - so there @@Tonksyyy_
@@rupert5390 damn. I think I’m gonna trade in mine too, never been that happy with it
I'd just put on an EGR blanking plate on. And be done with it. The engine will thank you too. No more crap being recirculated back into the engine ;)
That is bad for the enviroment. Shame on you
Great video ,and very helpful "do it yourself info". Will tackle my 130K klms, 2015 NP300 with better confidence after your video. Will probably install the blanking plate ,depending on how much gunk has been collected as mine has been all highway kilometres. Many thanks again for your clear explanation. Now subscribed. Martin
Thank you! :)
THANK YOU for this video boss.
Thank you so much. The content of this video is clearly and effective
Thank you :)
Many many thanks brother
Great video!!, Mas magaling ka pa sa master garage!!
How about sir cleaning the intake manifold...do you have a video? Thanks...
Leyend🔥🔥🔥⚡️⚡️⚡️⚡️
Mine has 120 mil km, will try this asap.
Great video followed and worked great for about 3 days then went back to running like shit and heavy black smoke, Will pull it out again and clean it better. I would add also to have something under the EGR Valve when pulling the 2 coolant lines off as I did not and got coolant on my belt and squealed terribly for a week. I'm thinking of putting a blanking plate on but cannot find one here in Mexico. Anyone know if I take sheet Aluminum or Stainless steel and use the gasket as a template will this work?, obviously not cutting out the centre part.
How regularly should it be cleaned
Great tutorial. Thank you!
Question: Can a blocked/ filthy egr cause a diesel smell to come through the air con into the cabin?
Nope, it shouldn’t :)
thank you video ! 23-12-22
After cleaning EGR, any need for ECU relearning or whatever?
thx
Is this the same for a 2016 pre adblue model?
Great content!
Just trouble shooting my throttle body.
Removed the pipe from the intercooler
To inspect and clean.
Discovered that the plate is stuck in the open position.
Any thoughts.
Hi! Unlike gas engines, diesel throttle bodies are normally open as default. They’ll only close upon shutting the engine down. You may confirm it’s operation by idling the engine with the hose/pipe of to observe the throttle body butterfly then turning the engine off (butterfly should shut close, then open). Just make sure you have scantool ready to clear any fault codes or check engine light afterwards as the ECU may get a low boost reading and throw a CEL
how about close EGR
hi . what about canceling the EGR ? it is good ? and if i cancel it do i need to programing the vehicle
No just block the ports with a blanking plate from ebay and you will be sweet as..
What is the size of the star torx socket sir?
E8 size of star socket
What is the total millage should I clean the EGR?
Best to have it cleaned every 50K miles
If disconnect agr valve will the motor controll light be on?
Make sure it’s connected before starting the car. If you leave it disconnected it might throw a check engine light
@@btdgarage
Thanks.
Regards from Thailand
Mike
@@mikekohlmeier8720 ... Grüße aus Nong Khai.
How many kms on the engine for this egr clean?
No, the question is if the engine gets warm enough , so long trips or short trips
boss, can i use a WD40 for cleaning te EGR valve?
WD40 is a lubricant, better to use petrol or carb cleaner for it. Just keep the EGR/sensor upright to avoid liquids seeping in and damaging the sensor
@@btdgarage Boss thank you for the info. God bless
@@babyfaceshotgun6042 God bless you too bro
its way to easy than the montero gen 3 😱
Can I DIY this? Is there any special tools needed?
Absolutely. No special tools needed except for the torx star socket to remove the studs
@@btdgarage what size of torx ?
Dumating na blanking plate ko from thailand. I think i dont need to disconnect the coolant hose since iblablank ko lang naman dba
Yes no need na
Hmm mine are 12mm and not 10mm
Ano po size ng star socket sir?
E8 po ang size ng star socket
Bos magkano nmn magpagawa ng ganyan sa mga shop. Any idea lng..
bro just inquire to my Motech Auto shop they are charging..
ang clean egr sir
labor: 2800-20%=2240
cleaner: 350
total: 2590
ung turbo cleaner hnhntay q pa po ung inorder q po eh 😊😊😊
Boss after cleaning egr no need relearning?
Its all on point but the bolts are not 10mm they are 12mm
Sorry for that :)
The 12mm on mine are very tight and broken my spanar, starts torn the shape of the bolt head, I stop the process😢😢
pano po yan i delete? haha
Ayaw matanggal ng bolts super tigas
This doesn't look like my 2017 np300 😮
... it is the 2.3 engine from Renault ...
screw that....... sea foam. will clear it...... NP