Thank you very much. I was working on one of these that someone gave me and knew nothing of what they did to it. I replaced carb and it then started to run but wide open. Looks like they adjusted the governor in efforts to get it to run. With the help of this vid and one from @Steve’s small engine saloon Got it right. 🍻 cheers
THE PRINCIPLE OF THE REGULATOR is as follows:As soon as the engine starts up, the regulator (and its weights that operate with centrifugal force) located in the engine, acts on the output axis and systematically brings the gas flap "to low speed"the idle screw used as a stop, but depending on the position of the lever turtle or hare the regulator spring (precisely rigged) more or less tense has the opposite effect of counteracting this movement which tends to go towards the idle and therefore "regulate" the engine speed that is expected, maximum,to 3600 trs for these HONDA engines and to 3000 trs mn on the old BRIGGS AND STRATTON and 2800 trs generally for the "Chinese engines"
I did this twice and took tension off spring by bending arm up but still runs real fast. Is governor inside engine the problem? I can hear the arm stop inside engine.
@@rf5101 It turns out the governor arm got bent when the rod went out. I decided to get a new arm when I ordered the new governor and old governor arm would not slide out. I had to tap it out. It was stuck wide open. I put it back together. I resealed the pin that holds the cam in place also because it was leaking. I will let you know how it turns out.
We sell GCV160 Ignition Coil with Spark Plug that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Let me know if you are interested.
Great video, short and simple. Great for people already understand little about small engine adjustment.
Couldn’t agree more. No intros straight to the point.
Thank you very much. I was working on one of these that someone gave me and knew nothing of what they did to it. I replaced carb and it then started to run but wide open. Looks like they adjusted the governor in efforts to get it to run. With the help of this vid and one from
@Steve’s small engine saloon
Got it right.
🍻 cheers
Your welcome
So make sure everything is
turned/going right and tighten that sum b down. lol good silent video, better than half the ones guys are speaking in.
Thanks
Thank you very much, your video was very useful to me.
Bellissimo video, semplice nella sporgazione. In pratica bisogna lasciare gioco tra la leva e il perno delle masse.
very good video
THE PRINCIPLE OF THE REGULATOR is as follows:As soon as the engine starts up, the regulator (and its weights that operate with centrifugal force) located in the engine, acts on the output axis and systematically brings the gas flap "to low speed"the idle screw used as a stop, but depending on the position of the lever turtle or hare the regulator spring (precisely rigged) more or less tense has the opposite effect of counteracting this movement which tends to go towards the idle and therefore "regulate" the engine speed that is expected, maximum,to 3600 trs for these HONDA engines and to 3000 trs mn on the old BRIGGS AND STRATTON and 2800 trs generally for the "Chinese engines"
what is the part sticking out your turning in the start of the video?
Ciao .... volevo sapere se la leva va registrata in questo modo come da video sul tagliaerba GV 160 .
I did this twice and took tension off spring by bending arm up but still runs real fast. Is governor inside engine the problem? I can hear the arm stop inside engine.
I'm having the same issue as you .Did you find a solution?
@@rf5101 It turns out the governor arm got bent when the rod went out. I decided to get a new arm when I ordered the new governor and old governor arm would not slide out. I had to tap it out. It was stuck wide open. I put it back together. I resealed the pin that holds the cam in place also because it was leaking. I will let you know how it turns out.
@@rf5101 I put oil in engine and will leave it over night to make sure it’s not leaking oil before I mount it back on deck.
Thanks for keeping me informed.
@@rf5101 have you done anything to it?
I thought the clip was pushed counterclockwise.
We sell GCV160 Ignition Coil with Spark Plug that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Let me know if you are interested.
Interested
@@DarkendSun 🥳
How can we contact you?
What the......??