Thank you so much for this. My screen was far more heavily cracked than the one you show, and also didn't turn on at all. I was also worried about damaging an otherwise-fine camera - I've used it for the past year with black gorilla tape over the cracked-screen for water resistance. The newly-replaced screen looks better than I remember, and works perfectly.
My xt3 screen powers on, then after 30 seconds of recording, it glitches with colours and lines, rgb, and goes dead. Do i need to replace it or is it another issue?
I just followed the steps and all went well, I thought. But now the camera does not even power on at all. I can see a few flashed on Green light from the LED on the back, and looking trhough the viewfinder, the LCD display there also flashed momentarily, but then all goes black. So the camera can't be used. I'm trying to figure out what I could have done wrong in this simple process. Yes, I did touch the connector on the display cable with my bare fingers at one point. But surely that cannot corrupt the whole camera? Can the new display be faulty and draw too much power or something? I have next to zero knowledge in this field, was just hoping to save some bucksand replace the screen myself :(
Hi, sorry to hear about your issue, though I don't have a solution. All I can suggest is retracing the steps ensuring all connections are clean, use contact cleaner, and connections are correctly fixed.
@@larry8056 От паров клея это. Нельзя так клеить. Клей наносить только на рамку (пластиковую) дать просохнуть и потом уже прижимать. Только так, и болльше никак. Сам так убил один экран.
Ok it seems the XT3 has different connectors, the connector ribbon is still short so this guide should work. If you follow guide you should be able to remove cover to see what the connectors look like and if they are same as the the screen you are ordering. There seems to be some who are unhappy with the sound on this video! Note at the time I had a sinus infection, I also have a deviated septum both of which meant my breathing was as good as could have been. If you are unhappy with the sound, please skip to another video showing howto to change the screen. thanks
Ordered the screen, did all the steps and made absolutely no mistakes during the process BUT the screen unfortunately still does not power on :/ I guess it must be something wrong with the motherboard or other part of the camera?? Btw the screen is not cracked or anything I just thought that that is the damaged part as it doesn’t work. Also, no tapes have been ripped or damaged.
Unfortunately if it did not power on before screen replacement it is unlikely to power on after screen replacement. This is a solution for broken screen.
Hi, thanks for the video. I think my flat cable that connects the screen to the body of the xt2 is damaged. Do you have any tips for that, specifically for the part that is connected in the camera body? Thanks.
My screen got white lines on it then stopped working. I cant get it fixed as I live in a remote country. Do you think I should check the cable connections ? And yes you are right there is nothing about screens on xt2 online because my camera has been busted a year and Im always looking for a fix.
I tried to repair my xt3's cracked screen and now its not turning on at all- ahhh! Tried to reattach the old LCD but neither will turn on. The camera itself still works fine but just LCD doesn't work anymore. Do you have any suggestions??? I'm desperate
Yes took photos and put it back in the same way as best I could- maybe the copper shield isn’t exactly on correctly or maybe something is jammed in one of the connector on the motherboard. I’m starting to think I damaged the flat ribbon cable connected to the motherboard, but it appears undamaged from what I can see… I’m worried to open up more of the body though because I don’t want to create more damage @Michael Innes
Ни в коем случае не далайте так, как делал автор ролика. Клей наносится только на пластиковую рамку (чёрную) и ему даётся время что бы улетучился растворитель. И только после этого, аккуратно вставляете и прижимаете дисплей (сильно не давить). Иначе привет жёлтые пятна на местах склеивания.
Thank you very much for posting this guide.
I was able to replace my screen with ease thanks to this video.
Does it work as well for XT20?
Thank you so much for this.
My screen was far more heavily cracked than the one you show, and also didn't turn on at all.
I was also worried about damaging an otherwise-fine camera - I've used it for the past year with black gorilla tape over the cracked-screen for water resistance.
The newly-replaced screen looks better than I remember, and works perfectly.
Do the touch features of the screen still work after this repair for an X-T3?
My xt3 screen powers on, then after 30 seconds of recording, it glitches with colours and lines, rgb, and goes dead. Do i need to replace it or is it another issue?
I just followed the steps and all went well, I thought. But now the camera does not even power on at all. I can see a few flashed on Green light from the LED on the back, and looking trhough the viewfinder, the LCD display there also flashed momentarily, but then all goes black. So the camera can't be used.
I'm trying to figure out what I could have done wrong in this simple process. Yes, I did touch the connector on the display cable with my bare fingers at one point. But surely that cannot corrupt the whole camera?
Can the new display be faulty and draw too much power or something? I have next to zero knowledge in this field, was just hoping to save some bucksand replace the screen myself :(
Hi, sorry to hear about your issue, though I don't have a solution. All I can suggest is retracing the steps ensuring all connections are clean, use contact cleaner, and connections are correctly fixed.
My xt3 have some kind of small reddish 'smear' on the left side of the screen... Dont know why.
did you figure it out? i have the same problem
I have the same but purple, did yours clear up?
@@larry8056 От паров клея это. Нельзя так клеить. Клей наносить только на рамку (пластиковую) дать просохнуть и потом уже прижимать. Только так, и болльше никак. Сам так убил один экран.
Ok it seems the XT3 has different connectors, the connector ribbon is still short so this guide should work. If you follow guide you should be able to remove cover to see what the connectors look like and if they are same as the the screen you are ordering.
There seems to be some who are unhappy with the sound on this video! Note at the time I had a sinus infection, I also have a deviated septum both of which meant my breathing was as good as could have been. If you are unhappy with the sound, please skip to another video showing howto to change the screen. thanks
Could you do this with an x-t5?
Hi admin, Does the xt3 and xh1 have the same lcd screen?
At 14:20 you said "Fix Copper Cable Shield From Old Screen" Can you please explain that part, please. Thank you for this video.
Have a look at around 8.30 you will see a copper shield on right of screen. It is this shield you need to move to new screen.
@@thefixer2468 Alright, thank you!
Ordered the screen, did all the steps and made absolutely no mistakes during the process BUT the screen unfortunately still does not power on :/ I guess it must be something wrong with the motherboard or other part of the camera?? Btw the screen is not cracked or anything I just thought that that is the damaged part as it doesn’t work. Also, no tapes have been ripped or damaged.
Unfortunately if it did not power on before screen replacement it is unlikely to power on after screen replacement. This is a solution for broken screen.
What's the specific screen part called to order?
what is the best vendor to purchase the screen replacement. If you could provide a link that would be great. thanks
Where did you buy the replacement screen?
Ebay
Hi, thanks for the video. I think my flat cable that connects the screen to the body of the xt2 is damaged. Do you have any tips for that, specifically for the part that is connected in the camera body? Thanks.
Then find a ribbon cable replacement
where i can Buy XT100 LCD Flex Display Screen Hinge Cable FPC??
My screen got white lines on it then stopped working. I cant get it fixed as I live in a remote country. Do you think I should check the cable connections ? And yes you are right there is nothing about screens on xt2 online because my camera has been busted a year and Im always looking for a fix.
You can try checking the cable and connections, worth a try.
@@thefixer2468 thank you so much I shall give it a go 😀
От клея могут появиться жёлтые пятна по краям. Клей надо наносить на рамку и давать ему просохнуть. А вообще лучше клеить на специальный скотч.
Thank you [the this video!
Ordering a screen now. Wish me luck!
Hey! Did you ever repair the screen? How'd it go?
I tried to repair my xt3's cracked screen and now its not turning on at all- ahhh! Tried to reattach the old LCD but neither will turn on. The camera itself still works fine but just LCD doesn't work anymore. Do you have any suggestions??? I'm desperate
You may have damaged a connector or are not connecting it correctly.
How do I know if I damaged something? How do I know if ai connected it correctly?
@@MariaWentley by ensuring you put back as you took it apart, I am assuming you took photos of every part of disassembly?
Yes took photos and put it back in the same way as best I could- maybe the copper shield isn’t exactly on correctly or maybe something is jammed in one of the connector on the motherboard. I’m starting to think I damaged the flat ribbon cable connected to the motherboard, but it appears undamaged from what I can see… I’m worried to open up more of the body though because I don’t want to create more damage @Michael Innes
Thank you
The breathing is killin me lol
I guess it's the same for the X-H1. Repair costs 250 euros. I am buying the screen and glue. Thank you very much.
Hey, howd it go?
wow!
Utiliser un sèche-cheveux chaud... et une lame de rasoir très fine... pour retirer le circuit collé à l'arrière...
Utiliser de l'alcool (dégraisser), avant de placer un filet de colle sur les bords de l'écran (remontage)...
Please teach us how to replace HDMI port!! I swear you!
I wish I saw this before I removed the whole connector and opened up the whole back of my X-T2 🤦♂️
Ни в коем случае не далайте так, как делал автор ролика. Клей наносится только на пластиковую рамку (чёрную) и ему даётся время что бы улетучился растворитель. И только после этого, аккуратно вставляете и прижимаете дисплей (сильно не давить). Иначе привет жёлтые пятна на местах склеивания.
Now it's glued it can never be repaired again.
Now what is glued?
It was already glued, John - that's why he used the heat gun, to pry apart the existing glued screen. He left it the way it came.
fatal, bad movie quality