AMSOIL: Diesel Bypass Filter Solution
ฝัง
- เผยแพร่เมื่อ 20 ส.ค. 2024
- If you rely on serious diesel power, AMSOIL diesel oils and bypass filtration systems provide the protection you need to fight wear and extend engine life. Inside your engine, soot particles smaller than a human hair are attacking your turbo, cams, and bearings
It is up to your diesel oil and filtration system to protect these critical components and maintain your diesel power. Unfortunately, no matter how good your oil and filter, some dirt and soot will contaminate your engine.
Diesel pickups come equipped with a full-flow filtration system. All the oil required to properly lubricate your engine flows through the filter fast enough to properly maintain proper operation and achieve sufficient oil cleanliness. These full-flow filters remove particles from the oil large enough to cause catastrophic damage (typically 20 microns or larger) but they allow smaller particles to get through and circulate inside your engine, causing wear.
The solution to this issue is the AMSOIL bypass filtration system. These systems feature a second filter that eliminates most solid contaminates from diesel oil. Watch to find out how the AMSOIL bypass system sets the standard.
To order the bypass system or diesel oil for your specific vehicle, go here: www.amsoil.com...
Here are five tips to help you protect your diesel: blog.amsoil.co...
Follow us on social media:
Facebook: / amsoil.inc
Instagram: / amsoilinc
Twitter: / amsoilinc - ยานยนต์และพาหนะ
Amsoil has different By-Pass configurations that can be used for gas engine or hydraulic oil applications.
I have been using By-Pass filtration on my diesel trucks accompanied by oil analysis and have extended my oil drain intervals far beyond that of the OEM recommendations.
got a link for gas variety
@@Baigle1 It's just a filter, it doesn't care what type of fuel the engine burns. If you can find a way to route the oil through it, it's going to work.
great video.. i am running this system and have never got the oil to go clear again like in the video but i think this is because in the demo when it is switched over to the by pass filter its running 100% not 10%. still its better than nothing.
The reason is because the bypass filter is filled with fresh clean oil in the demo, and they only run it for a short time after switching it to the bypass filter. Every single demo you see like this they will cut away after 10-15 seconds. A 2 micron filter will filter down to 2 microns, but you'll never get new clear oil out of one. You'd need a centrifuge to get pure clean oil. Even then I'd imagine recycled oil is filtered through some kind of sub micron filtering or something else to get it clear again.
@@emrwtf tricksters. Not a fair demo thanks for pointing this out.
They may use a media bigger then 2 microns to show what is happening. Ive used amsoil for about 20 years. In oil analysis it's performed better then Rotella and some other oils I tried. another logger noticed a huge wintertime starting gain on his 700 hp chipper.
The demo is using black fine particles, it's not the same as old black oil, that has had constant heat and pressure and friction on it, and other changes done to it. Your bypass filter is working good and as it should. The color change in this video is simply removing those very fine black particles. And that is what it does. There is more going on in an engine that makes it turn darker. This is not a demo to show it can change the color or keep it a certain color, it's showing you exactly what it's supposed to do, filter those fine particles.
That's because in real life, your engine will have those ultra small soot particles under 2 microns, which will still color the oil. However, the oil will not be as thoroughly black and opaque as oil that hasn't been bypass filtered.
Thanks you for your outstanding
By-Pass oil filter, it is helping me cry!
No wonder Amsoil products are the best.
Yes but you are Amsoil dealer :) All dealers tell me it's great LOL
@@SerasPhilly it is great lmao
Amsoil beat all oils tested in the Project Farm you tube oil shoot out.
@@SerasPhilly Go look at the final shoot out on Project Farm between the 2 best oil winners. Amsoil finished first and he's not a dealer. chuckle chuckle.
@@firewoodtime2 Unfortunately, he didn't test bypass filters. Yes, Amsoil is probably the best overall oil, also, very expensive.
Seen this system hooked up to a 6.7 cummins with new amsoil and filter, within 1000k miles the oil was as black as it was before adding an amsoil bypass filter system. Just change your oil every 4k-5k
Nearly all commercial diesel engines are equipped with a bypass oil filter from the factory to extend oil changes due to soot loading. A pore blockage PARTICLE COUNT on your oil analysis report will determine if fine particles are a problem requiring removal by this system, most engines don't need the additional filtration unless oil changes are extended beyond the OEM recommendation.. This same demonstrator was used thirty years ago as an illusion.
I see no high filtration filters on the C15, C13 Cats and ISX Cummins on the trucks I drive, just regular cans, please explain.TIA
@@Clunk49Oil filters can do both full flow and bypass, that technology has been utilized since the 70's by Mack & Mercedes. Mack & Volvo use a separate bypass filter. www.cumminsfiltration.com/sites/default/files/pdf_archive/pdfs/product_lit/americas_brochures/LT36043.pdf Baldwin also has an excellent dual element oil filter for the ISX. Some people add on an extra bypass filter, its completely optional and comes in a spin on or a cartridge style (TA/Petro is a vendor for one brand).
Thanks!
An excellent video!
this kit will not fit a 2020 GM L5P Duramax diesel engine....Amsoil does not manufacture the correct oil fill cap to work with this engine. Amsoil no longer sells the oil fill cap separate from the kit, which now forces it's previous customers to shop elsewhere for by pass filter kits. Truly a big disappointment.
Can i do this to a 6.9/7.3 idi ?
0:10 hardwood cylinder liners, nice. What is that? Mahogany?
looks like walnut to me.
Mahongany is open-grain you goose.
Honestly the factory filter was cleaning allot out before the switch was turned. I question the added media they used for demonstration. Because had they left the factory filter going longer it looks like it would of cleaned the fluid nearly identically the retutning fluid looks a tinted a shade darker from factory filter but not far off. I'm willing to bet this was rushed with thicker particels the factory filter could of easily removed.
Let's try a longer more detailed test with proven factors.
They used charcoal with a minimum size of 5 microns to ensure their bypass filter returns the oil to a golden colour. In actual life, soot particles can be 1 micron of even sub-micron in size; leaving the oil dark even if "clean"
What you asking is not good for their marketing. They do same con art as banks and fass.
I've pointed banks on few cowboy things or bad designs but they never replied to the hard questions...😁
I’d like a test with used motor oil, not a liquid with a carbon additive
I put one of these systems on a V8 and after 2k miles the oil didn't appear any cleaner/clearer then i used a clear plastic bottle and ran the motor to see whats coming out of the bypass filer line....dark oil
it may filter to smaller particulates but it defiantly does not "clean/Clear" oil
@@prodigy6000 that obvious and nothing surprising. As said above most american so called famous companies are just con artists that using lack of customer experience or knowledge. They sale pure bullshit.
Why they don't export to europe ? Coz in europe statistic buyer got huge mechanical knowledge so they won't be able to bend him over.
We did few tests of american tuning products and it was a joke no near promised specs in advertising.
can gas engines ues this filter also , i have a vw non desiel my deisel jetta cam went out i had to scrap the car
Why dont you test using used oil?
Silmi Isa used diesel oil will still be black. It’s a common misunderstanding to see black oil in a diesel and think it’s bad or dirty. Oil turns black due to temperature and is not a bad thing. This demonstration is meant to show particle removal only. To use, used, black oil, would not be able to demonstrate the removal of particles.
@@Misesian86 in particle filteration, the most important info that interest me is the particle filter size (micron) and filtered oil flow rate, especially after several milage served (typical condition). Hope we can get those info too.
Silmi Isa couldn’t tell you the flow rate. I run Amsoil bypass on my three semi trucks. The oil samples show it works. Oil is still very clean at 20% beyond manufacturer recommended interval. These newer trucks don’t use much oil, so I still change it due to TBN depletion. 20% beyond recommend interval isn’t bad. On the Volvo and Cummins trucks, I’m able to go closer to 30% longer.
How big are the particles in what was poured in???????
Pretty obvious they were 2-20 microns. Probably a single specific size, like 10 microns.
I would like one for my 2020 Silverado. I don’t see one on your site. Should I get the universal kit?
Make a version for gas engines and 1/2 the price and I'm IN.
So why do diesel trucks that have this system still have oil black as the ace of spades just after 1000 miles?
Oil turning black is normal. As soon as you turn on the engine with clean oil, and it gets to temperature, it will turn black. As soon as the oil is subjected to heat, it turns black. The black in this demo is carbon black to simulate wear particles. The black you see in every day operation is not soot, but oxidation, and is normal, not indicative of anything undesirable. Dark oil or black oil is meaningless, oil samples are the only way to know if it’s good or not. I have 3 semi trucks and all three have an Amsoil system on it. I even gave a bypass filter on one of my reefer units, from a different manufacturer. Oil bypass filtration is a proven, effective technology.
@@Misesian86 I don't buy that at all. Oil has to burn to turn black that fast, which would be burnt oil. What's burnt is the diesel fuel, which is sooty, which is scraped into your pan by the rings or blowby. Dark oil and black oil are two different things. On my corolla after 1k miles its still not soot black, which is what the dude was asking about. Black that you cant see through is soot, not oxidized oil. You can test it yourself by heating some motoroil up to 250 in a pan on your stove. keep stirring it, it wont turn soot black. It may darken up some, but it wont turn soot black.
A diesel engine is always gonna have black oil, but its not due to oxydation.
@@emrwtf
Heating it in a pan does not subject it to pressure. Oil turning black means it’s doing its job. No amount of bypass filtration will fix that. I run oil samples on all my stuff. I know what the soot content is. On both my semi truck and reefer unit, it’s less than 1%. Anything higher than 3% should make you examine things. Between heat, pressure, and soot, oil will darken and turn black. My point is that the color of oil is meaningless. If you took two identical samples, one full flow, and one with a bypass filter, the one with bypass will have substantially fewer particles, over 1 micron in size. The point of bypass filtration is extend drains and reduce engine wear.
@@Misesian86 Everyone has a right to their opinion. We can agree that bypass filters work, and leave it at that.
@@emrwtf Diesel engine oil is black due to soot from combustion. Having owned both diesels and a Corolla, I can confirm that (with Amsoil and filters) the oil never turns truly black, but more of a golden brown, because it doesn't have the same source of soot that a diesel does.
Why is the oil black after changing it with the bypass filter on a diesel? What does that mean if it's black?
Brent S...............The black oil in Diesels is small particles of "SOOT" that are very small, like .0000009 that you see. When these small particles AGGLOMERATE (Gain Growth) and become larger, the by-pass filter will then take them out,but the very small soot particles will still be there causing the oil to look black.
It can’t remove all the particles greater than 2 micron. Why? Because one is likely generating enough fine soot that one is re-adding soot to the oil as it’s being cleaned. . One question is how many engine hours does it take for the filter to catch up and remove say 50% or the soot from the last lead foot.
Not long. The flow rate means that all of the oil is filtered every X minutes, somewhere between 1 to 10. Depends on the engine and the setup.
What kind of pump is that being used
Does it come for 1.5 liter diesel engines?
It will work for any engine just need the oil filter adapter to screw into you engines oil.filter location or custum make one for your engine if you cant find one that fits
What pressure is required for your demo unit
Can this system fit any Toyota? 1vd-ftv engine?
I’m planning on order one for my 2015 duramax but you have a dual filter bypass and a single which cost more..so which ones better?
Did you go with one? My 2015 has 100K miles and I'm thinking about a bypass system.
@@ericwiltz6584 no i didnt still waiting for a response lol
@@JonLIsALoser I don't like the dual remote bypass idea. It doesn't make sense to me, and I have heard some people have problems with it. Get the single bypass remote filter system and retain your existing full flow filter.
@@JonLIsALosersingle
Will this product lower oil pressure to the engine and cause damage from lack of lubrication
No. It only draws a small percentage off the oil flow. I've got one on my 6.0 Powerstroke and it's great!
@@BestEngineOil did you mounted the filter the same way as the Sinister diesel videos or another way?
@@banderasXx69 Since I had purchased the kit from Sinister Diesel before becoming an AMSOIL dealer, I went ahead and installed it. It's an excellent kit if you want the truth, it includes the awesome AMSOIL bypass oil filter and a bypass coolant filter. VERY happy with it! My 6.0 stock injectors love the finer (cleaner) oil now as a result!
Mine dropped ever so slightly at cold and midrange, but I also switched from fleet blend oil to amsoil signature series.
@@StarHunter28 Oil pressure is not everything. As long as there is enough, there is enough. Extra doesn't help anything.
I run thinner oil, for start up (5w-40 for diesels) and yes, the oil pressure is lower on startup, but in reality, the flow is higher because it flows more easily. Oil pumps are positive displacement, pumping a non-compressible liquid. Therefore, for each revolution of the engine, X volume of oil is pumped. If the oil pressure is lower, that just means it is pumping more freely (or in a worn engine, it's getting out in more places more quickly).
When it gets too low, like if there is fuel dilution, that's where you have problems, because the oil is too thin to prevent wear.
Hmm how come my oil doesn’t end up clean like that but is a sooty mess.. not saying they don’t work or aren’t good to have, I just bought one and have it on my older truck too.. just saying
David B.................Soot particles are very very small, in the range of .0000000009 (1 MICRON) so the oil will be black, as there is NO OIL filter that will take out that small of a soot particle. However, when these small particles Agglomerate (come together and gain in size) The 2 micron By-pass filter will take this size particle out, but the oil will be black!
Does this work on gasolina engines too?
Dont need that on gazoline engine.... change your oil regularly
Yes. They do. I installed one on my 6.2L sierra. Amsoil made it, says Amsoil on it. So yes, gas engines benefit from these. Diesel engines don't need them either if you want to put it frankly. Nothing needs them. They benefit from them.
I need an ams oil filter for my 2017 arctic cat alterra 400 atv
Nope
Как называется это оборудование?
Question I have. Why not just make this same filter to fit the OEM housing? Instead of having to do all this to add your own. I mean I want this but really don't see why I have to add all this bypass stuff and install a whole new housing.
The filter is too restrictive to be a primary filter
Too restrictive
It would be way too restrictive, not allowing enough oil pressure for the engine to run safely. Heck, might be lucky to just run the engine 30 seconds like that before is had a total failure or just stopped running.
On your website its not available for 2021 silverado1500 3.0l duramax. When will it be available?
Just means they don't have a specific kit for that application. You can still buy the parts and put it together yourself. You just need an oil source, and a return, usually the oil sending unit, and then returned through the filler cap, or oil pan tap.
There's hardly any full flow filter that filters less than 40 µm you just wouldn't get enough flow
I put 300 miles after the install. Oil is still as dark at it was... Is that normal?
Oil is still dark, yes that's normal. But if you look at it very, very closely you'll see the oil has much less soot in it, compared to the same miles on your truck's oil without the bypass filter. I will admit the demonstration in the video does not accurately portray oil color of a LIVE, running diesel engine. It DOES show the idea or concept of bypass filtration. A running diesel engine is generating soot and giving away as much free soot as possible wherever exhaust meets oil, like cylinder walls in the combustion chambers. And the engine is running 600 to 2000-3000 rpm under normal conditions and pumping quite alot of oil per minute for lubrication, and other things like powering injectors in my 6.0 Powerstroke for example. The regular oil filter is a full flow filter, it filters the full flow of the oil while still allowing the necessary high oil pressure for adequate oil throughout the engine. Meanwhile at the same time the bypass oil filter is only filtering a very small percentage of the oil flow so as not to interrupt the necessary high oil pressure which would cause engine failure and a terrible, expensive repair. And it's doing so down to a much smaller particle size, which is the whole point and purpose of it. It is the best way I know to filter down to 2 microns instead of the regular 20 microns in size the regular filter provides.
@@BestEngineOil thank you!
Does it remove the zinc
No.
Does Amsoil Bypass filter lower oil pressure on 6.0 Powerstroke?
Thank you for the question, Michael. The AMSOIL Bypass System will not affect the oil pressure in the engine. The pressure needed to for the bypass system is reserve pressure the engine oil pump generates, and will not have reduce the oil pressure to the engine parts.
We hope this is helpful. If you have any additional questions, please contact our Tech Team at Tech@amsoil.com or by phone at 715-399-8324. Thank you!
-The AMSOIL Team
When I installed this kit and switched from synth blend to amsoil signature, my oil pressure dropped about 10 psi cold, and 5 psi midrange. However at idle it is about 3 psi higher after working hard so I think it's just due to the oil being superior and more stable.
Where did you guys get this test rig from?
Did you get an answer?
@@lloydrees7674 no
Acme Testing Supply.
So it’s not a bypass, it’s a slipstream.
Not that I doubt Amsoil products, but now that I know it’s a slipstream, I’ll be looking at one in the near future.
price in Bangladesh please help us
Likely can’t get it. Based in America maybe you could ship it?
These tests are misleading . Would love to see this test done on 10k oil.
@qwerasdffzxcv - It's a demonstration, not a text. Countless laboratory oil analysis reports validate the effectiveness of the AMSOIL bypass oil filtration system. - 30 year Independent AMSOIL Synthetic Lubricants Dealer.
The Amsoil filter is made by fram
so changing oil more or paying hundreds of dollars for by-pass it may take out the particles but the additives break down dont they? i lost my trust with amsoils 25k gas filters, i went to about 10k miles and the oil was black as if it was in my 1970 chevy with dino oil. normally when i cange every 3-5k my oil is still clear on teh dipstic.. somehow i dont feel amsoil is telling the whole story. plus with the info on bypass filters....WHY WOULD ANYONE WANT TO GO TO 25K AND LOAD THE OIL WITH 50X THE AMOUNT OF DEBRIS BELOW 20 MICRONS? THAT DONT MAKE SENSE. ONLY THING THAT DOES. IS PUT TEH BYPASS FILTER ON, AND CHANGE THE OIL THE SAME. AND HAVE YOUR ENGINE LAST LONGER.
These demonstrations always cut away after a few seconds of the bypass filter running. It is instantly clear because the bypass filter is filled with clean, fresh oil. So when it is switched over you think, wow that's amazing. They are more than likely only dumping larger micron particles into it also. There's no need for this type of illusion BS but they all do it. Diesel oil is still gonna be black due to the sub 2-3 micron soot particle in it. It would turn black with 0.5 micron soot in it too. Like people have commented before, you have to send in oil samples to know how it's doing. If you look at other peoples data that is posted all over the place, you can easily extend your oil changes by double the miles, but to be sure you'd need to sample and decide for yourself. In my opinion they are worth installing if you plan to keep the vehicle long term. If you get a new car or truck every 2-3 years you probably don't need to bother. 2 micron particles will still wear on your engine, just slower than 20 micron particles. Think of it like sanding with 200 grit and 800 grit on wood. If you use enough 800 you'll still sand it down, just takes longer.
@emrwtf - Making incorrect, damaging statements about a company is illegal. It's called libel. People committing libel can be sued in court and lawyers are very expensive. Libel is also in violation of TH-cam established rules.
@@HiTechOilCo little late to the party bud. That comment was a year ago. Also it is my opinion, which is perfectly legal as per the constitution. Just like it is perfectly legal for you to have an opinion about my opinion. You really have nothing better to do?
scam
Waste of money
@henryvasques8629 - Reducing oil change costs, greatly reducing wear and improving fuel economy is a waste of money? How do you figure?
pretty much. Just change your oil on time.
The high school engineering degree has spoken
It's a lie. Doesn't work. Other utubers have tested it. Sorry
Steven Bryant............I installed one of these system on a 1994 Dodge/Cummins powered pickup, and ran it for 10 years/155,000 miles, and took oil analysis every 12,000 miles, and never changed out the oil, so yes, they do work!
@stevenbryant3752 - Making incorrect, damaging statements about a company is illegal. It's called libel. People committing libel can be sued in court and lawyers are very expensive. Libel is also in violation of TH-cam established rules.
I smell bullshiiieettt
@bonholio0o - Not at all. It's old hat The AMSOIL bypass oil filtration system has been used for decades.
can this be used with gas engines?
Fake!!!!
I agree with you. The oil coming out of the first filter was just as clean as the second filter.
th-cam.com/video/vXmX5LJk2IE/w-d-xo.html