STAGE 2 map for 1.9tdi
ฝัง
- เผยแพร่เมื่อ 7 ก.พ. 2021
- This is my stage 2 map , used in my audi a4 b6 avant 1.9tdi pd130 awx. I used this map for almost 2 years without problems.if you like this kind of video , you can check my other videos too and help me with a subscribe.
My car mods:
-straight pipe 63mm
-single mass flywheel ceramic disk(custom)
-front mount intercooler + hardpipes
-AL injectors from ARL
-Hybrid turbo gt1749va with cold side from gt2052v
estimated power -around ~200hp
Music in this clip is downloaded from : www.bensound.com - ยานยนต์และพาหนะ
Thank you very much for taking the time to make these videos , a very interesting insight to custom mapping.
Love the video get me subbed waiting for more,
Keep up the good work
Maybe could you do an stage 2 for an asv (110) vp? I love seeing your videos
Hi there very interesting the part where the dur maps correspond to a certain working degree or rpm, didnt know that, always learning, i just have one question, to achieve that SOI you add to work on SOI limiter map a bit right?Or its not necessary? I have a 1752vb in my pd130, and my work on the ecu till now is good, the car feels great, but i have to put FMIC, some IAT temps happening with SMIC. Greatings from Portugal.
Hello, Nice video.
What do you use to read and write in the ecu?
Thanks
Do you have any reccomandation, on a A4 B5, with PD130 engine. 4bar map sensor. PD150 injectors, GT1856V, FMIC and straight pipe? what i should run when it comes to injection quanity etc still runing a stock clutch so dont want to max it out at 250. trying to keep it for a while haha
Hi!
How can I get the turbo to fill up sooner? Regards,
Ed
Can you make a video with 1756vk and Cupra intercooler which dowpiwpe 70mm and hard pipes 60mm
I have a question. I have vag edc suit but I don’t have the stock map file or any data to change. Can I download it from my ecu through a obd 2 port or do I have to download a file online?
Waiting some other tutorials in winols. Thanks!
Hello friend, I have a question, can I add 100mg to the maps or will it block the ECU?
Hi do you recommend remap map to ecm titanium?
u are legend help me with all videos
Does edc suite only for for vag group?
why yo dont use stock injectors??
Daca fac o mapa identica de 101cp cu asta, are cv ? De cați cp e mapa ?
Great vídeo, can you share the file? Tanks
Salut ! Observa ca esti roman , imi poti spune daca partea rece de pe gt2052 se potriveste pe partea calda la gt1749 ?
Yes. The gt1749va turbine is only rated to 1.6 bar without egts getting excessively hot. So a gt1752va would only do 2.6 bar boost pressure safely. I dont know about the vb.
Salut, sesizez ca esti roman dupa accent, la un alh cu turbina de asz, cam cat de cat boost ar fi nevoie?
turbina aia functioneaza pe asz cu 2350mbar maxim pe harta de fabrica. o poti duce la un 2500...max 2550 ,ca sa nu o violezi prea tare.
Would you write for guys like me in South Africa
Hi i want to do the same thing using the vnt20 (gt2052) cold side with 1749va. I want to know how much diference is in spool time? The lag is much noticiable? Thanks in advance!
there is not such a big difference in spool time. it depends on your afr. more fuel , faster spool.
@@AnotherCarChannel1 thanx!
Hej, i dont get it why it uses duration table 0 only if its 25 degrees before tdc. I mean how should it know how long the injector is gonna be open otherwise ?
the map "selector for injectior duration" at 25 degrees uses duration table 0 that's why
You say on the torque map that it will inject around 75-80mgs instead of the requested 70mgs because you changed the ratio. You never showed that ratio change?
i was talking about duration maps . in duration map 1 ,i inject about 36 degrees at 4k rpm. and 36 degrees its more than 70mg. With stock 520 AR/BA injectors from awx/avf engines you need ~32 degrees at 4000rpm for 70 mg of fuel, but i have 550 injectors from ARL, with bigger nozzle..thats why i said i inject around 75-80mg.
@@AnotherCarChannel1 Thanks. I thought I had maybe missed a new trick for scaling bigger injectors.
Hello can you please contact me? I have the same setup but on a passat. I am interested in the map , could you please send me it?
Software download pls edcsuite
Hi, i have copied your settings but i'm overboosting +2bar, how do i get this down to the target? :/
You had to make your n75 setup higher.
@@lukasstiftner1167 doesnt it affect the engines "breathing"? Loosing power?
@@lukasstiftner1167 i have set it at the High boost to 94% just for it to be around the target but does it not affect the engines "breathing" 😅😅
@@mads501010 Max on n75 duty I would make 78%.
@@lukasstiftner1167 but then its too High in boost 😅😅
Hi can I use this map for 105 PD ?
105 PD original? Go stage 1
@@pedrovicente3926
Thanks
Hello my friend please you can help me im hace a problem whit my stage 2 1.9 TDI pd ajm, whit ARL inyectors, 3bar map, 2052v turbo please thanks so much!!
whats your problem i want to do the same setup as you with my ajm?
@@acclrtester183 hello, I would like you to give me your opinion about my stage 2 and also that you guide me to solve my problem is that I have a pressure peak in the duty cycle at 3100-3400 rpm... and I wanted to lower it a bit since I know It goes from 2bar... I want 1.8 bar max.. how can send you my file and my logs
@@juanicosanchez2792 sorry it's not my video. I am also intersed in this setup this why i asked about your problem! i'm planing to install soon a 2052 in my ajm.
Is this safe for a 1752vb?
Look for a compressor map and find out the compression ratio.
I have a few questions about your turbo
what do you want to know?
@@AnotherCarChannel1 what is it
Its a hybrid turbo. Half its from audi 2.5tdi . The cold side.
@@AnotherCarChannel1 can i comtact u anywhere else ive got a few more questions
@@joegermaine4208 facebook.com/adriano2br