Congratulation for your initiative, go on. your are one brilhante worker. This is what the world necessity, people helping people, teaching your knowledge you sediment the your personality on you, preserving your exemple for the world.
@benzblogsVlogs hi thanks for the great work I'm asking if i can disconnect one of the sensing input 7 or 8 until the motor tourn on high speed 1500 then connect it back to have full output directly? Would that harm any of the avr or generator?
@benzblogsVlogs the engine must run in pre-heat and idel speed for 36 seconds in same time it gives 25 hz with 190 volts and I'm afraid that it will damage some equipments so I want a way to disable the avr until the 36 pass and the engine speeds up to 1500
If ever over current is the problem meaning your load is above the total full load of your generator now if volatge is the problem Meaning that you need to check the voltage during load and without load if satable of not
Thank you boss i enjoyed watching and learned about stability. My generator DSE110 is has a huge difference in the phases no matter how much i tried to adjust the voltages it will still show me under voltage what can i do for this situation
I have done that several times I Have even changed the contact terminal. I notice the phase 1 terminal has worn out and I immediately change it because there was some amount of spark trace I saw. But it still showing under load and at times it will run normal.
Hi I bought an SDMO T16 diesel generator for power restoration when the local utility company has blackouts. The generator works well and runs well but five minutes after loading the voltage starts to have these huge swings in values. The problem only occurs when loaded, so I’m thinking it’s not a AVR problem. Do you have any suggestions?
Ok meaning the confige or the nominal volatge in the module not reaching out from volatge from your alternator for exampls you module nominal is 220 it shout be the volatge reaching 220 not below if below it happen like this loading voltage
hi Brother...i have a question regarding same AVR MODEL the voltage will drop in a sudden when heavy fog is coming or due to rain....my location is Saudi Arabia thank you
Hello, I have an SS341 that I can't get control of throught DSE. I have trim all the way up and can't get it to drive down or up. I am stuck at 102 percent
the avr itself. It was stuck at 102 percent. I went straight from back of DSE AVR A and B to AVR A1 and A2. I got control but when I restart the engine, AVR goes up on it's own@@benzblogsVlogs
@@elporky6420 before you do the adjust ment for the avr put first in the midle posation the voltage thin adjust the setting in the module so you can get the exact value for +- percentage
Bro Can you share me or tell me how is AVR , Speed controller Located ? Are they coming single module in big DG? Ecm means avr and governor modules? Can you share schematic how gensent controller is connector with avr , speed controller,ecm etc, cannot find anything google as a full schematic
Bro avr is connected only in the alternator while ecm is connected in engine The function of avr is to regulate the volatge while ecm is to control engine fueling and metering like sensors
If no out put just double check your fuses and check the resistance of your exciter field if there is around 10_20 ohms still good now you can start exciting
Follow the vedio that i send to you take the exciter wire and strat the genset try to inject 12 vdc but before you do remove all the connection from your avr and each one put some insolation for safety thin follow the vedio if build voltage from 300-500 means avr only is defective if now build while exciting thin ither exciter or diode but after that message me back
Just do this check first if your rpm or your speed is stable if stable thin you can adjaut the volatge from you avr and stability but if rpm not atable you have to fix that first before you adjust the stability of the avr
Hello brother. How are you? I am a new subscriber to your channel. I am honored to join you to follow. I have a problem with the 45KVA generator. Its voltage was unstable and suddenly I lost one of the phases and 2 phases remained working as required. The problem is in one phase. It no longer exists. What is the problem and what is the solution? Is the AVR malfunctioning or is there Another problem. Is there a problem if you run the generator on 2 phases? Thank you. I wish you success
Now if you lost one whase of your volatge means other winding is damage already no if you want to know open the alternator use migger test if winding still in good condation in main winding
Now if unstable your volatge due to other line lost so if you have multi meter check the volatge where your avr sensing is connected my be its affected coz the is line failure
Thank you, engineer, and thank you for your interaction with me. I wish you success, brother. But can I make the generator run on 2 phases? I checked them. They carry a stable voltage of 230V.
Sir pano naman kung pag start ng generator tapos mag flactuate yung volts then pang stable ng rpm papalo sa 490V yung voltage nya? Ano kayang cause nun at how to fix po. Salamat and godbless
Now kong hindi stable ang speed hindi talaga stable ang bogay ng boltage kc malaking apikto sa alternator yang hubting ang makina unahin mong fix ang makina thin bago avr
good day sir,good idea po may makukuha kami kaalaman about generator,lalo na kagaya ko bago palang dito sa generator.
Welcome2 thank you
Napaka importante Ng mga nalaman ko d2 vlog nyu sir.... maraming salamat Po sir ....stay safe and god bless you sir
Salamat sa pagtitiwala sir
Bless you too
Nice one idol salamat sa pag share ng video mo.dagdag kaalaman na naman yan idol..
#1 ka tlga idol. God Bless for sharing
Sir thank you bless u
Thanks brother for the clear demo and explanation appreciate 🙏💐
Welcome bro
Congratulation for your initiative, go on. your are one brilhante worker. This is what the world necessity, people helping people, teaching your knowledge you sediment the your personality on you, preserving your exemple for the world.
Thank you sir bless you keep safe God be with you
@benzblogsVlogs hi thanks for the great work
I'm asking if i can disconnect one of the sensing input 7 or 8 until the motor tourn on high speed 1500 then connect it back to have full output directly?
Would that harm any of the avr or generator?
If you do that it not reaches to the speed 1500 it will shutdown undervoltage or under freq because there is safety configuration during that process
@benzblogsVlogs the engine must run in pre-heat and idel speed for 36 seconds in same time it gives 25 hz with 190 volts and I'm afraid that it will damage some equipments so I want a way to disable the avr until the 36 pass and the engine speeds up to 1500
@@ماقل.ودل the problem there it will work but it give more harder work from your avr and your alternator excitation to work with
Your videos are very useful
Welcome sir
Good work... excellent.
I'm asking for what's the problem ... Over current voltage.
Sir over current at the same time over voltage?
If ever over current is the problem meaning your load is above the total full load of your generator now if volatge is the problem
Meaning that you need to check the voltage during load and without load if satable of not
Nice idol more vlog thank you for sharing. Godbless idol
Same with you bless u too
Great! Keep up the good work buddy
Thank you
You are the best.
Bless u bro
Good job sir, god Bless you
Bless u sir
Very good video sir. Please do more of these vids
No prob sir
Thank you boss i enjoyed watching and learned about stability. My generator DSE110 is has a huge difference in the phases no matter how much i tried to adjust the voltages it will still show me under voltage what can i do for this situation
Is this 3phase or single phase
Check your wiring and configuration and the fuses
Use multi meter to check ✅
It is a three phase sir
I have done that several times
I Have even changed the contact terminal. I notice the phase 1 terminal has worn out and I immediately change it because there was some amount of spark trace I saw. But it still showing under load and at times it will run normal.
Good explain, thank you
Bless u sir
is that compatible with the brush generator?
No brush type have defferent type of regulator
Nice information 👌
Thank and bless you sir
How to fix over frequency alarm in Genset ? Thanks
Check first if all stable speed and voltage not go to module config and add delay for 5 sec for over freq
Hi I bought an SDMO T16 diesel generator for power restoration when the local utility company has blackouts. The generator works well and runs well but five minutes after loading the voltage starts to have these huge swings in values. The problem only occurs when loaded, so I’m thinking it’s not a AVR problem. Do you have any suggestions?
Ok meaning the confige or the nominal volatge in the module not reaching out from volatge from your alternator for exampls you module nominal is 220 it shout be the volatge reaching 220 not below if below it happen like this loading voltage
What do you recommend? Do you believe the problem is with the AVR?
hi Brother...i have a question regarding same AVR MODEL the voltage will drop in a sudden when heavy fog is coming or due to rain....my location is Saudi Arabia thank you
Sir you need to install anticondensation heater to avoid that problem
Ita use toremove existing moist in your alternator
Nice 👍
Thank you
Nice 👍👍👍
excelente información muy completo
Thank you
Hello, I have an SS341 that I can't get control of throught DSE. I have trim all the way up and can't get it to drive down or up. I am stuck at 102 percent
Your the engine or avr
the avr itself. It was stuck at 102 percent. I went straight from back of DSE AVR A and B to AVR A1 and A2. I got control but when I restart the engine, AVR goes up on it's own@@benzblogsVlogs
@@elporky6420 before you do the adjust ment for the avr put first in the midle posation the voltage thin adjust the setting in the module so you can get the exact value for +- percentage
Could you help me with as440 indicator light not coming on?
In your module
Double check your configuration look to your loading voltage ithere same amount with your nominal or higher juat put 95% from your nominal boltage
Sir ung pag adjust ng stability clockwise o counter clockwise?
Sir pweding clockwise pwedi ring anticlockwise kong saan po sya magstable pero dapat kongi lang ang pihit
Sir how we can calculate excitation voltage. Please provide formula for calculation.
th-cam.com/video/bNfpvuttD-wh/w-d-xo.htmlere you can see the excitation base on the manifacturer
Please explain mx 341 AVR CARD because AVR regulation go to direct 100% In my DEIF CONTROLLER HOW TO SOLVE EXPLAIN
If i have time i hive u axlaination
Did you put 150 ohms for your speed control?
Sir papaano mag insulation resistance sa main stator, rotor, at exciter module ng mga ganyan na type na generator
Sir kailangan mo lang ng migger in order to test this kind of insulation test
Bro
Can you share me or tell me how is AVR , Speed controller Located ?
Are they coming single module in big DG?
Ecm means avr and governor modules?
Can you share schematic how gensent controller is connector with avr , speed controller,ecm etc, cannot find anything google as a full schematic
Bro avr is connected only in the alternator while ecm is connected in engine
The function of avr is to regulate the volatge while ecm is to control engine fueling and metering like sensors
@@benzblogsVlogs engine speed controller? It is another module or it is the ECM?
Can I please know how we can change its connection from 220v to 380v
What avr you use
So i can make the wiring for u
My generator always over frequency shutdown what could be the problem
Souble check volatge and hz if stable thin check your config put delay for over and under 5sec
Hey brother i have problem with my AVR there is no input power how can i check the reels please
If no out put just double check your fuses and check the resistance of your exciter field if there is around 10_20 ohms still good now you can start exciting
th-cam.com/video/ZRACQ2uzbNM/w-d-xo.html
Follow the vedio that i send to you take the exciter wire and strat the genset try to inject 12 vdc but before you do remove all the connection from your avr and each one put some insolation for safety thin follow the vedio if build voltage from 300-500 means avr only is defective if now build while exciting thin ither exciter or diode but after that message me back
Sory sir, I'm try adj.The AVR. Affer that, still unstable voltage & hz, of generator 😔😔😔
Do have vedio if posible
Dear engg.... How to solve the voltage fluctuations on load
Just do this check first if your rpm or your speed is stable if stable thin you can adjaut the volatge from you avr and stability but if rpm not atable you have to fix that first before you adjust the stability of the avr
sir pano po kaya kapag nag under volt warn? sa AVR po ba yun?
Sir pweding sa load and sa config feom the module
NİCE
Shukran
Hi brother kirloskar 400kva voltage up down why how to solve this problem
Double check first engine is stable or not if not make correct first thin voltage stability
Hello brother. How are you? I am a new subscriber to your channel. I am honored to join you to follow. I have a problem with the 45KVA generator. Its voltage was unstable and suddenly I lost one of the phases and 2 phases remained working as required. The problem is in one phase. It no longer exists. What is the problem and what is the solution? Is the AVR malfunctioning or is there Another problem. Is there a problem if you run the generator on 2 phases? Thank you. I wish you success
Now if you lost one whase of your volatge means other winding is damage already no if you want to know open the alternator use migger test if winding still in good condation in main winding
Now if unstable your volatge due to other line lost so if you have multi meter check the volatge where your avr sensing is connected my be its affected coz the is line failure
Thank you, engineer, and thank you for your interaction with me. I wish you success, brother. But can I make the generator run on 2 phases? I checked them. They carry a stable voltage of 230V.
Do you have watesup my brother
I need contact with you please for this problem .and thank you so much my brother
Anung purpose ng droop c.t sir ?
Para saan din po ang droop adjustment sa avr ?
Droop sir using only if your in paralleling or synchronizing
Sir pano kong ang hz mismo ang pumapatak sa 55hz tapos biglang bumababa sa 45hz tas ang normal na bigay is 48hz? Then ang ang generator is umuugong?
Sir that is overload if your enhine like this make aure your kva is in correct load
Sir paano kong wla tlaga voltahe na lalabas sa output ng generator pinalitan ko na lahat ng diode posible ba na sira na ung avr?
Pag avr lang sira dapat may boltahi parin lahit 40-50
Ganito testerin mo yung exciter ilang ohm dapat omabot yan ng 10-18 gnayan ok payan
Mag migger test kana
Sir pano naman kung pag start ng generator tapos mag flactuate yung volts then pang stable ng rpm papalo sa 490V yung voltage nya? Ano kayang cause nun at how to fix po. Salamat and godbless
Sir ganito una mong tignan if pag start mo dapt stable rpm mo or speed para doon kalang magfucoz sa avr
Now kong hindi stable ang speed hindi talaga stable ang bogay ng boltage kc malaking apikto sa alternator yang hubting ang makina unahin mong fix ang makina thin bago avr
Anong makina at ilang kva