Hi, which pump do you have on your frame? I wanted to mount my topeak pump with the original topeak mount, but it does not fit as the frame is to wide. Thanks for your answer.
hello,i just received my cascade orbea link and install it as the official video.But i found it difficult to install shock extender（the yoke) with cascade link when the washer put on it's place。Seems like the washer should not stand between extender and the link。With no choice，i had to install extender first，and then install link to axle。
The one I got is out of stock but this is similar. 8MILELAKE Blind Inner Bearing Puller, Hole Remover Extractor Set, 16pcs Blind Hole Collet Bearing Race and Seal Puller Extractor Kit, Slide Hammer Tool Set a.co/d/6IQCkYX
Did you not use loctite anywhere when re-assembling everything? Btw...my 6 months old bearings where toast and the same tool did not do ANYTHING for me :-( Had to knock them out from the inside.
Awesome video man 🙌 . I've been considering the Cascade Link, however my Rise is mullet setup with 160/160. I am wondering if I still could use the Cascade link with my setup and won't throw off my current geometry since the link is set for 150mm rear shock position / mount.
What calculators did you use to find the spring you needed? I was on a 500lbs spring (push 11-6) and with my cascade link, my quick calculator run said to go to 575 - just installed, and I'm basically using full travel just parking lot bouncing. Curious your experience and if you felt like you ended up needing more spring.
Nice video, why did you increase the spring. Im about to install my cascade and wondered why you did this. Havent seen or heard anyone else doing that.
Hi there just get the linkage installed but now my chain is funny.. do you know how many link are in your chain? I think the longer travel require one or two extra link.
Hi, thanks for the video. I am considering the Cascade for my H30 with DVO Jade X progressive coil. Are you still happy with the Cascade? No problem with more pedal strikes or too plush from the top?
![Cascade Components [ORBEA RISE] Link Installation W/Ride Bicycles](http://i.ytimg.com/vi/7n-gPuqW7Gc/mqdefault.jpg)
I have an orbea wild and you won’t believe how useful your videos are. Thanks a lot 🙏
That's some smooth slider hammer action. Can't wait to see watch the comparison review
Years of practice on that stroke action LOL
Hi, which pump do you have on your frame? I wanted to mount my topeak pump with the original topeak mount, but it does not fit as the frame is to wide. Thanks for your answer.
hello,i just received my cascade orbea link and install it as the official video.But i found it difficult to install shock extender（the yoke) with cascade link when the washer put on it's place。Seems like the washer should not stand between extender and the link。With no choice，i had to install extender first，and then install link to axle。
Can you post an Amazon link for the tool you used to remove the frame bearing? Cheers!
The one I got is out of stock but this is similar.
8MILELAKE Blind Inner Bearing Puller, Hole Remover Extractor Set, 16pcs Blind Hole Collet Bearing Race and Seal Puller Extractor Kit, Slide Hammer Tool Set
a.co/d/6IQCkYX
@@allshownogolf Cheers dude!
Did you not use loctite anywhere when re-assembling everything?
Btw...my 6 months old bearings where toast and the same tool did not do ANYTHING for me :-( Had to knock them out from the inside.
Awesome video man 🙌 . I've been considering the Cascade Link, however my Rise is mullet setup with 160/160.
I am wondering if I still could use the Cascade link with my setup and won't throw off my current geometry since the link is set for 150mm rear shock position / mount.
I think it can be done, but not sure if you want the rear travel to be more than front though?
Is you bike the aluminum version I heard the aluminum version has trouble installing, but it seems like yours went in no problem
We updated the link awhile ago, there are no issues on alloy frames anymore.
hey, I have an Orbea Rise H30 bike and I have this strange shooting from the right swing arm, what do you recommend doing?
What calculators did you use to find the spring you needed? I was on a 500lbs spring (push 11-6) and with my cascade link, my quick calculator run said to go to 575 - just installed, and I'm basically using full travel just parking lot bouncing. Curious your experience and if you felt like you ended up needing more spring.
@@bokehcreativesfineartstudi4304 TF Tuned 👍🏻 no problem so far
@@allshownogolf thanks!
How much do u weigh?
@@YLDCRD 230 fully geared up
Great video
Nice video, why did you increase the spring. Im about to install my cascade and wondered why you did this. Havent seen or heard anyone else doing that.
Increase in travel will definitely need an increase in spring rate. You can check the TFTune spring calculator 👍🏻
Hi there just get the linkage installed but now my chain is funny.. do you know how many link are in your chain? I think the longer travel require one or two extra link.
@@fabrizioferla5789 Not sure, I didn't need to change chain size though
È stato facile togliere la Loctite 638? Come hai fatto?
È stato abbastanza facile. Hai solo bisogno di riscaldare le parti.
I want to try this bit im overstroked to 160mm already. Wonder if it would work.🤔
If you're already running offset bushings with 216x63mm shock then I wouldn't be cause it would probably boost it too beyond 170 of rear travel.
Thats what i thought. I just hate the creaking w the stock setup. Ongoing issue.
You can watch my old vid on that, easy fix with strong locktite so the linkage doesn't move around the axel splines. Cheers
Hi, thanks for the video. I am considering the Cascade for my H30 with DVO Jade X progressive coil. Are you still happy with the Cascade? No problem with more pedal strikes or too plush from the top?
It's amazing you will love it!
Great to hear, thanks! Did you ad a stiffer spring with the Cascade? And no more creaking linkage?
@@btentusscher yes you will need stiffer spring due to increased travel. No creaking with the spacer kit
I’m using the Cane Creek Valt progressive 550-670lbs spring (my weight 88kg) and don’t want to go higher. Problem you think?
@@btentusscher I'd plug it into the online calculator, or even just try riding it and see how you feel and see if you bottom out
Hi mate much extra weight does this add on replacing stock ones + the new preload
Hey bud I didn't weigh them
@@allshownogolfdid it alter the bb height? Is it lower now more pedal strikes ? Also is your set up long shocked?
@@1spiders1 I used stock shock configuration so BB height is the same, no geo change
@@allshownogolf ok so how is it then? Worth £350 ?
@@1spiders1 Yes, I have follow up videos for my impressions but I love it
You obviously went for the "cheap" cranks :-D
🤣😅🤙🏻