1998 - 2004 Toyota Tacoma Backup Camera Install
ฝัง
- เผยแพร่เมื่อ 15 ต.ค. 2024
- Parts linked in the description below!
Watch a full tutorial as a 2004 Toyota Tacoma will have a backup camera installed. We will be using a license plate mountable camera and integrating it to an existing aftermarket Pioneer touch screen radio.
This video applies to Toyota Tacoma models for years 1998, 1999, 2000, 2001, 2002, 2003, and 2004. This video also includes camera wiring, complete installation, and testing.
*For the full radio install, click here: • 1998 - 2004 Toyota Tac...
*For the amp and sub video, click here: • 1998 - 2004 Toyota Tac...
*For the front speaker install video, click here: • 1998 - 2004 Toyota Tac...
*For the rear speaker install video, click here: • 1998 - 2004 Toyota Tac...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Backup camera used in this video (Amazon Associate Paid Links):
*AutoVox License plate camera kit: amzn.to/3w9lyAL
*Split Loom: amzn.to/3Wx80cR
*18 Gauge wire: amzn.to/3y2qK7x
Radio Parts Used (Amazon Associate Paid Links):
*Pioneer AVH-120BT Bluetooth Radio: amzn.to/365sQY4
---Recommended CarPlay / Android Auto Radio: amzn.to/3fTLw2X
*Metra 70-1761: amzn.to/3z8PT1y
Disclosure: As an Amazon Associate I earn from qualifying purchases - ยานยนต์และพาหนะ
Parts used linked in the description of the video!
Great video. I did find the 12V reverse wire can be accessed up by the driver floorboard, and you can splice and run the trigger wire from that location, eliminating the need to run it all the way back to the camera. And then the camera just needs ground, so you can just tie that just about anywhere, so you don't have to mess with the taillight. Thanks for the clarity about accessory power and all the explanations.
@elliiothart18 I’m looking to do this route, you connect the trigger wire to the driver side wire and the other end goes to the reverse camera wire on the harness? And you didn’t connect ground or power from the backup camera harness?
Trigger wire is power (tire that to camera harness), and tie ground to ground (camera harness, anywhere you want).
@@elliiothart18 do you have a fb to message you on, it’ll be a little easier or a email. Haha, I left a T on my red wire on the radio harness and I connect that to which wire? The to trigger it off my my reverse which wire do I go to, I also have a trailer plug and play that I’m wiring in and led c bar taillights
Thank You so much Mr Provo Beast! I have an '03 and just now got a backup camera to use with my double DIN head unit. Since I am no electrician, I had to watch it a dozen times, but I now have rear camera on demand, and in reverse! I was tempted to just do the reverse angle but glad I did the extra wire. Thanks again!
Couldn’t had made it any better thanks 😎
Thanks!
Thank you!!
I've seen in some if your older videos you turned your radio on In your house, how do you do that?
i installed this camera and the image needs to be reversed. The problem is this camera does not have a WHITE LOOP wire to cut to fix this problem. the head unit also does not have a setting to fix it either...
Will all this apply to a manual transmission Tacoma same generation?
Yep, same process!
Wehy would it say no video feed?
Either a short in the video cable, or the camera isn't getting power.
I think its a different kind of hook up, it has the red wire off both ends and i didnt see in the video where to terminate the small red on the end of the video cable closest to the camera. I played around and could only get the video to stay on always or just work as intended with the truck in reverse. I appreciate the video tho
what lift is your tacoma on?
Not a personal vehicle.
where does the green wire is connected .????
The parking brake wire? There is a wire off of the parking brake mechanism that we connected it into.
BUYER BEWARE on this camera!!! they ship them stuck in the reverse view position. I have tried two units, both do not work properly, the switch on the harness does not work on either one. DO NOT BUY THIS PRODUCT