ฝัง
- เผยแพร่เมื่อ 22 ก.ย. 2024
- 🔔 Please CLICK THE BELL if you want to see my videos! 🔔
If you've ever looked at one of those Amazon or eBay car cameras and wondered how you wire it, maybe this will help. Yes... that red lead coming out of the video cable can be used to run power to the camera... and I had a surprising accidental discovery about the ground!
Here are the cameras I am using: amzn.to/2wU6U3j
Some helpful O3D Jeeps links for you:
Most Recent Upload : goo.gl/z2AFkB
Most Popular Upload : goo.gl/y6bCWo
Check out my Channel : goo.gl/t8crvN
I was looking for a simple explanation on how to properly wire a backup camera & I found the bulk of imy answer here. I had to watch/read other tutorials for a better explanation re: the red pigtails, but you explained it perfectly. BTW, in my particular situation, the red pigtails on both ends of the RCA cable serve as "trigger" wires. The end that attaches to my Pioneer head unit attaches to the wire labeled "reverse trigger wire" & the end going to the rear camera connects to the reverse light positive wire. In my Toyotas case, it's the black wire coming out of the bulb assembly. The two triggers work in tandem to switch the camera on when putting the vehicle in reverse.
Very good. You got the basics covered clearly in less than 5 minutes compared to the "other" guys that took twice as long to make things somewhat confusing. Thank you.
Especially when they tell you their life story before describing what u were actually looking for in the first place
As far as the ground wire that is part of the 12v feed at the camera end, you may not want to connect it to ground. This is because there is already a ground connection at the head unit (monitor). If you connect grounds at both ends you can end up with a ground loop. If you have screen flicker with backup camera activated, try removing the ground connection at camera end and you may find that flicker disappears.
I've installed a dozen of these cameras and there's nothing new this video can show me- Wait What?? :O
That red wire on the video cable is for instant on in reverse. It is connected with the power wire to camera which is connected to reverse light and the one at the radio side connects to your radios wiring harness labeled reverse gear signal input. So now when you put in reverse it automatically switches to camera mode and when you put it in drive it then will go to the last mode you where on.
This was what I also thought as well. I didn’t think it was for actually powering the camera, but only to wire with the head units reverse trigger wire.
I know this post is couple months old but I got a question here I just bought a new stereo android and its got brake, reverse and key 2. can you tell me what is key 2 and brake for where do I wire them up at
Thanks
Aaron Darren if your car doesn’t have those wires, I believe you just leave them alone
@@guccimane5752 I found out what they are and your correct those wires are for vehicles who don't have keys on their steering wheel
Thanks bro
So do you hook the black and red both to the reverse light?
My head unit (cheap but good, Boss) has backup camera and alternately rear video feed selection from the touch screen, so I chose to draw power from my rear license lamp. I can now turn the camera on/off with my driving light switch.
I don't have to be in reverse to power the camera on. That way, I can see traffic behind me while driving: tailgater's license numbers or just watch behind me while parked.
I also hard-wired my mirror dash cam from my dome/courtesy lights (ignition hot,) so it starts recording as soon as I start the car and there is no wire dangling down to my cigarette lighter. I did have to buy a separate 5V USB step-down transformer, but it looks stock, with only a 2" lead going under the headliner.
My mirror cam has an extra video feed to record both from the front-facing and a second camera. I could split the feed from my backup camera and run the video signal to the dash cam to record both views.
But, I chose instead to install a second cheap camera pointing out the back window, powered the same way, for higher resolution. This would work with any brand camera, head unit combination.
Thanks man everyone else on TH-cam makes this set up look messy 🙎🏽♂️ but this videos great !!
Perfect. Just what I needed to know. Been to 4 different Auto electricians to connect a power and ground for me and they all fobbed me off to come another day as it's a lengthy job and 1 even went on to say he needs the trigger wire to run to the reverse lights too lmao. Watched your video. Camera was already in place as well as wiring. Just connected the trigger to the red on camera and it fired up in reverse. My xtrons unit actually had a wire labelled reverse behind the headunit so other trigger wire went to that. Literally took me 5 mins to get my reverse camera working. Thanks again
Can you explain this again please? My radio instructions say to connect Headunit's brown (Back/Reverse) wire on its harness to Car reverse trigger wire. I already fed the Camera at Rear Reverse light harness in trunk. I found the Bulb/harness and tapped the (+) to Red of Cam and (-) Black to Ground in trunk also. The NightVision LEDs go on when I put gearshift into Reverse but Camera does Not show up on Radio. What do I connect Brown wire to from Headunit?
@@chrisb8870 Sounds like you do have power as the leds turn on. Are you sure you connected the camera video feed to the correct input on headunit side? Try other inputs too incase they been labelled wrong on headunit.
Did you connect the small red wire on Camera wire/Near Radio to anything? I didn't connect it because I already connected other end of Red wire/Camera Side to reverse lights wiring in trunk. Do you still comnect the other red to the radios wire(Marked Reverse)
@@chrisb8870 Yh so my radio (xtrons) had a wire on headunit side for it to connect to. I used the trigger wire only and didnt connect to reverse light at all but my headunit also has canbus so it only needed the trigger wire to get it working when putting in reverse
Just tried this! It works. No need to ground the black wire to ground. Power can come from the radio connection. Connect the red cables together at the camera end. Thanks!
The red wire that runs in the harness with the yellow video signal wire is meant to be used for the signal from the camera back to the head unit so the head unit knows when to switch the screen to camera mode. This video makes no mention of this important function. Also, the only time you wouldn't need to connect the camera ground wire is if the camera mounting hardware was acting as a ground through contact with the vehicle chasis.
I have an android head unit. Can I set the rear camera to record all the time, but still take the screen when put in reverse?
The android radio turns the video mode automatically on as soon as you put reverse. Even if the camera is not installed at all!
No it doesn't.
As far as the ground wire that is part of the 12v feed at the camera end, you may not want to connect it to ground. This is because there is already a ground connection at the head unit (monitor). If you connect grounds at both ends you can end up with a ground loop. If you have screen flicker with backup camera activated, try removing the ground connection at camera end and you may find that flicker disappears.
@@batfenderman7212 if that's the case you should run the ground wire from the camera to the same spot that you grounded the head unit. You shouldn't use the RCA as ground.
This way of installing the power wire at the radio end only works if the radio switches to reverse camera mode using CANBUS, if it's a cheep Chinese radio the camera end needs the red connected to the reverse bulb 12v feed and black to ground or leave disconnected and use the phono plug ground, the red wire at the radio end will need to be connected to the radio reverse signal terminal.
I did just this and I'm still getting black screen with grid lines. I've triple checked my connections and everything seems to be connected properly, what can I try differently?
Thank you! The instructions that came with my camera said to hook up both red wires to power and I thought that didn't make since and it should be one or the other. Glad I found your video.
I too wired an aftermarket camera (nearly identical to yours) to a 2-DIN aftermarket head unit in a VW Jetta Sportwagen - these cars have CANBUS. As any other "standard" instructions, I have tapped into the Reverse Light connector. What happened was that I would turn the key to Accessories (only), shift into Reverse and have video feed. However, with the engine operational when shifting into Reverse I would only get a blank screen with only the grid lines-feature incorporated into that head unit.
I combed through a lot of videos on youtube and various information in forums and finally I have seen someone's comment who said that if the CAR HAS CANBUS - do not tap into Reverse Light. If the new head unit preserves the functionality of the Canbus then it should power up automatically the camera when shifted in reverse. That's another tip.
What I wanted to comment about is your "Ground" note toward the end. Actually I disconnected that separate or "local" ground wire when troubleshooting my situation and the camera had no feed. I too was thinking that the ground is already carried out through the RCA wire to and through the head unit which is already grounded. That was wrong. As soon as I reconnected that local ground I had video feed. I'm not sure what your further research has unveiled, but you might consider amending your video (which provides an excellent how-to, btw) with complete information concerning that local ground wire.
Thanks. good luck
Hello Ionel P. Just came across your comment while looking for the solution for my reverse camera. When I put the car in reverse, I only get that "blank screen with the grid line-features" as you mentioned. What did you say was the solution the get the camera to work normally? Thanks in advance
Peugeot 107 needs ground to otherwise there is no video feed.
This video clears it up for me. Was so confused about the two red wire sticking off the yellow rca plug.
Finally got an answer from you after watching 10 other videos. Simple and clear! Thank you for the vid!
Hello My name is ralphie, I too was searching for the rear view reversing camera. While looking through the images and reading the descriptions. It explains how one can connect the red and black wire meaning the negative and positive to any reverse brake light. I was confused for a little while, but I didn't realize there are so many different reversing cameras for different vehicles. And what I also realized is that most of these products don't include extendable wires to make the connection easy and comfortable to install. Great video.i definitely understand how it works thanks.
Awesome, thanks for the explanation of that mysterious red wire!
Great. Thanks
So question... will my radio, I just got the Heigh10... will that notify my camera to turn on or do I still have to tap into my reverse wire on the taillight?
thank you. Your first 3 minutes I think answers my questions, I will find out tomorrow.
Thank you! This makes it a lot more clear. I've been searching on the internet everywhere and have been very unsuccessful in finding an answer. Thanks again!
I was searching for this type of video, and finally, I found it! I just installed my reverse camera by connecting the red wire to the head unit backup 12+ve cable, and it worked perfectly. Surprisingly, I didn't need to connect the two red and ground wires near the camera. I assumed that the ground is already included in the video cable, and we just need to provide the +12V from the head unit.
But I'm now wondering if our rear camera will always be on while driving using this method??
I test everything works but the cables not long enough to reach to reverse light so I try to extend the cable cemara works but video is flickering?any ideas
You didn't mention the reverse trigger wire which is going to confuse people. Most people use the red wire on the RCA cable for the reverse light to trigger the camera. The way you set it up you will have access to the camera at all times but unless you run a separate wire for the reverse trigger it won't automatically come on when in reverse.
I did the wiring exactly the same as in this video, but for some reason when I switch to reverse I get the message no signal. I connected the yellow cable to the head unit's yellow cable labeled "video in". Can someone tell me what I did wrong? or could it be that I did not connect the ground to anything?
I have the same problem 😞
Just go to your reverse camera settings and select NTSC
Surely the power cable that runs with the AV cable is to connect to the back up / trigger wire on the head unit. Thus when reverse is selected, power is supplied to the back up wire, and the radio/head unit automatically displays the camera image.
yeah...this video is essentially wrong. You need to hook that red wire (w/ the video cable) to the reverse trigger on your stereo.
@John Kuehn yeah well he should be more clear. This this video is very unhelpful and misleading on what the end result.
@John Kuehn yes! That’s what I’m trying to do. Have the camera to turn on at will since my unit will let me view up to 4 cameras. So basically I need to wire the red extra wire on the video end to a constant hot? What’s hot in the back of a Jeep?
@John Kuehn yeah. I must have connected it wrong behind the radio then. I do think it’s best to wire it to reverse as it will automatically switch on the screen to show the camera when backing up right? But I got the heigh10 radio yesterday and it does allow you to install 4 cameras and view them whenever. I just can’t get the wiring correct in back I guess.
Trial and error I guess. So only one end of the video cable with the red wire needs to be connected not both ends I assume?
@John Kuehn Im pretty sure I did that. As it said power but no luck. I’ll go back in and see what I did wrong. But thanks. I’m understanding now. I thought I had to connect the red wire that’s at the end of the camera aswell. But it’s just one end. Thanks for your kindness in responding though.
An added tip that I use is to not use the ground wire spliced to the backup light ground wire. I drill a pilot hole near in the body near the camera, then rotary brush the area around the hole to get bare metal. Crimp a eye terminal to the ground wire and attach it to the chassis hole with a self tapping screw to ensure a good bond.
That seems like that’s a better idea than letting it ground thru the head units video ground. I’m no expert, but it seems like that tidbit of information he shared in this vid wouldn’t meet an actual electrician’s approval. Your way seems like it a better bet
You have the exact right way.
Can I install the red wire into the red 12v on the back of the head unit instead of the purple video viewer. And then run a wire from the kick panel and find the reverse light wire and run that to the purple video viewer cable? That way I can view the camera whenever I want as well as have it kick on when put into reverse? Thanks
Life is so simple when there is someone like you, who knows what they are doing, to show us the way. THANK YOU!!!!! Took me forever to find this amazing video.
When reverse is selected the canbus sends 12v to wire which can be used to supply power to sensors /camera or both 😁 it’s not a trigger wire it’s a 12v supply that is triggered by canbus. Earth or negative is not required as camera cable does that.
Thank God for this film....finally some answers. Great product horrible instruction sheet.
I totally agree about the instruction sheet. I had wired my camera both ways accordingly to that sheet and i still had no power going to camera. After watching this video i can go back in and fix.
how do i use this camera so i can view rear of car full-time?
I've tried everything but not getting any image on my video monitor
still not sure where to connect the little red wire to the screen side, my one is android screen after market have reverse camera rca connector, but no reverse wire to connect the red cable. i have parking sensor wire and brake in wires only.
Mike Kattan did u ever figure it out?
@@eddward758 just use a cable from your navigation that has the output of 12 volts. There should be a brown cable labeled "back" that will do the job
@@catacatalin9769 I tried connecting to that brown cable but it didn't work....
I have done exactly as you suggest - the camera works when I go into reverse. The issue is the LEDs around the camera are on 100% of the time when the car is on. I spliced the RED power wire at the head unit into the wire going to 12v Ignition?
My car, a 2007 Ford Mondeo, has a weird switched polarity tail light. What you think is ground is actually live, and turning on a signal, putting the car in reverse etc, actually switches on the ground for that light. I believe it's done this way so that if the car's control module fails, the lights turn on for safety.
So to get around that headache (and CANBUS), here's how I wired the camera.
The black lead from the camera went to a ground point near the camera. I used a tail light screw.
The red power cable connected to the red cable on one end of the video cable. I ran the video cable to the head unit and connected it to the camera socket on my headunit. The red power cable was then connected to my headunits remote turn on lead (usually used for amps etc). By doing this, I was able to get a camera that is permanently live when the stereo is on so can be used at any time.
My headunit wiring harness adapter had a reversing light signal output which I connected to the headunit reversing sensor.
Hey presto! The camera automatically shows when I enter reverse, or manually switch to the camera input.
Does Connecting the short red pig-tale the way you said to the power plug solve the interference problem?
And after putting them together i’m I suppose to connect them also to the backlight ?
The ground would be picking up off the camera ground ? what happens when the camera is incorporated into the number-plate light glass, then it would have no ground ??
Got my backup camera working finally in my 2010 tacoma. the factory one didn't work with the pioneer nex 1400 stereo. I bought a $15 cam from walmart & it still didn't work. I bought another $15 cam today from walmart & this one worked !
So how will the car know when too gets put in reverse? I just used the reverse wiring from the bulb
Great video just made my day the black wire has been doing my head in
I was trying to get through the rubber in my car and I damaged the end of the cable. I decided to cut and run the wire because it was thinner; now, I bought a new P2 power cable. Can I just cut it too and splice it to my old one? I saw that there are 3 wires. Or do you suggest to repair with a new plug?
“convenience wire “-(pigtail) that you connected to the “reverse switch-( behind radio) “ Can you explain more in-depth ... the reverse switch wire behind radio?
I should able to see a free short red wire behind Aftermarket radio harness? or find and splice continues red power wire behind radio? Did i get this right this far?
The tails are for the reverse power to head units with a reverse switch to automatically switch to camera mode.
christopher 0
Xfbidncbud
So one red to the head unite and the other red just nothing right
1 red to head unit, the other end plus the power in red are tied together and connected to the reversing light. When put into reverse, camera turns on, signal is sent to headunit to reverse.
ive done exactly that but i get "no video input on my headunit, what do i do
Dilan05 i think you have to go to your head unit and change the camera settings to on and the polarity option as well thays should give you video right away
The way you are wiring the harness, how does the headend unit knows you placed the vehicle in park?
Thanks for the informative video! I'm getting ready to install one on my TJ & the ATOTO SA102 headunit has the red 12V lead available. However if I want the camera to only come on during reversing would I use the other 12V lead close to the camera & tap into the reverse light power?
If I could give you a thousand thumbs up I would. Works perfectly. I watched so many other videos making it seem complicated when it actually isn't. Now not only can I see it when I reverse, I can tap the camera app on my head unit and turn it on whenever I want. Thanks.
hello what is a camera app i dont understand
@@Shepherdstudio1 like an Android head unit with a camera app
I'm confused why you made no mention of which wire from the harness you connected that to, yes 12vdc source but in some cases there is a few sources right at the stereo. My problem is I've already crimped my accessory red and my constant yellow and I'm looking at this blue wire that says remote output 12 volts 500 mAh, and I'm wondering if I can run it off of that rather than cut one of the lines I've already crimped.
Thanks, wasn't getting any feed until I hooked up the red trunk wire like you stated.
THANK YOU! So easy. Why hasn't anyone explained the red wire power source before. Holy cow! Trying to find the correct wire on Ram truck was driving me bonkers, every answer was different. Good video.
How did you connect it to your ram truck i8m getting power to to the Camara and lights up when in reverse but the head unit doesn't do anything
@@emoneybags6038 I’m having the same problem. What did u do to get the camera to work?
So about to install one of these in my TJ, i was planning on running the red wire off my backup lamp or hitch reverse wiring. If I am understanding correctly, I can ignore the red wire with the video feed if I am getting power from the back of the Jeep.
I am having a weird issue after connecting reverse camera to my head unit. After some intervals my head unit apparently gets a "noisy" signal and goes to "reversing mode". There's no video and the screen comes back to normal mode after a second. But this effects music playback and Normal operation. What needs to be done? I HAVE connected the ground pin to the ground though...
Very informative, it's exactly what I was looking for. Thank You!
Hi There. I have, coming from the camera to where the cable splits, two more wires. The wires are a light green and white. The seem to be looped out and then back in to the single wire side of the splitter. Any ideas? Thanks in advance
My red pigtail that comes off the yellow rca got pulled off (such a cheap pos). Its the part that connects to the rca on the camera. I wonder if i should not worry abt it or get a new wire?
Re: the red wire, I have one that is too short. How would I go about getting a wire to extend it? What size works? Thanks
So what triggers the camera to turn on when you put your car in reverse? Does one of the wires get spliced into the reverse light wire?
Hello, could you tell me how I find the reverse cable in the radio cables? It is to connect the small cable that brings the cable with the yellow plug in ford focus Mk2 2008,Thanks
Hello. Is it ok if the current flows that 10 meters through this very tinny cabel from the front of the car to the camera, is it not too big distance? Will it not affect negatively the camera after some time?
Think I may have wired mine wrong. I spliced Camera Red Power and Red RCA to Reversing Light. Black to Earth. Now on the Display I Spliced Red RCA and Display Power to Ignition. Black to Earth. Would I be correct in saying that all I needed was the RCA to Display so no need for power from Ignition ??
Cheers
A lot of people have asked but I haven’t seen an answer, does this method mean the camera can be viewed while not in reverse also since it’s connected to the head unit power source not the reverse light wire??
Does that carry power can I just hook the red wires and find a ground with the black?
Hi I have the power acoustik P-81ACRD 08-12 Accord 8.3" Touchscreen with Navi but in the back of the unit have the rca yellow for the camera but is not have the red wire
big thanks...im looking for hours...finally you answered my questions
I’m confused, I think this is a great way of doing it but wouldn’t you want it to turn on when your reversing? So would you like connect it to your reverse signal?
What's the red and black wires on the camera side for? Why does the camera need to have power and ground, doesn't it just need to have a video cable to transmit the video? So the camera won't work without the red and black connected?
Real quickly, I glanced at a pontiac g5 & the reverse lights are down beside the license plate, not within the tail light.at 1st glance, I do not see a good way of routing the camera wiring threw the trunk & out to the reverse light. I need to track the wires but, I also need opening to route the cam. Another issue I am having is the dimming if the head unit with the headlights. It does not have switched power on the red wire so, I ran a fuse tap to a switched source directly to the fusebox
Hi can you send me the link to what you did to epoxy the magnets to the camera please ?
Yes..the ground for power is connected to the video plug (the outside ring). Do a continuity test, plug in the power (red) plug at the camera end. The black is the ground and check continuity that to the video plug (outside ring) and you'll see they are connected...hence your ground.
I am having trouble getting the back up camera to work. I have a pioneer 2300nex. I just connected the red pig tail to the power wires to the camera. Then connect the RCV to the HU and the other pigtail to the red 12v wire but is still didn’t work. I tried it with the purple and wire back up camera too and it still won’t pop up. I know the camera work because it worked on my JVC with some diodes and a switch. Please help!!!
I have the apeman c770 and I don’t know what to do with the red cable, I have watched around 40 videos already and nobody explained it and manual is bad
they share the same ground or neutral line if they are directly connected to same power source (car battery). But there are dashcam monitors that are battery backed up to avoid relying on ACC of car.
I have a Wi-Fi rear camera should I wire it to a permanent live
I am making a replica Vintage broadcasting camera and want to use this setup. Is their away to wire to a Battery source so i can move around with it?
HIi bro...
I want to connect my rear cam having 5pin or 2.5mm pin ......
so how to connect 5 pin or 2.5 mm car cam pin to Android tab....? Which accessories is needed for that.........?
i connected everything the camera works on my touch screen but it wont go away? i only want it to come on when i go in reverse so im missing something
Very well explained. I did mine before watching this one. But it took a long time to figure it out. Thanks
can you cut the yellow RCA cable (though it's long but what if it is short) that goes to the head unit to connect a new wire, say 16 gauge wire, in between to extend it?
Bro, quick question .. if i use the constant power thats going to the head unit to connect the “ pig tail “ for the camera to power up.. how does it come on when i put the car in reverse?
Big help on understanding those red wire, thanks
But the head unit has a wire in the harness that is in my case is pink. It's says the short red wire next to the rca connects to that. Do you just connect the pink wire, the red wire and run them to my reverse light triggered 12v in my dash?
great video, it worked well
What if the end that plugs in radio unit isn't a video cable. It's a headphone type cable?
Are you sure the camera isnt grounded, completing the circuit? I thought thats how most worked.
This is incorrect if you want to use the reverse camera when you reverse your car. Don't follow this video if you want to use as a reverse camera. The red positive goes to your reverse tail light positive, the wire that travels with your video RCA is the trigger wire for your radio deck. Your radio deck will have a reverse camera trigger input wire. You solder to this. Too bad the video doesn't help with what most people want to use the camera is used for.
your error is in assuming that this video is about wiring a reverse camera. It is not. In fact, the camera I'm wiring in this is not used for a reverse camera at all. This video is about running power along with a camera using the red pigtail, in cases where installers need to run power along with the camera. This is not about wiring a reverse camera.
@@o3djeeps This is the problem here. 90% of the people watching this video are trying to install a reverse camera. Your video does not state that it is for a reverse camera but it doesn't specifically say that it is NOT for a reverse camera either. Yeah, your setup won't work for a reverse camera install if you want it to kick on when you put it in reverse.
@@GrnXnham All you have to do is run the reverse signal wire from your aftermarket headunit down to the kickplate where the reverse light wire is and tap into it. Then it will work when you put it in reverse and you will also have the option to turn it on while driving.
@@Nickoli0811 I'm not sure I understand how this provides camera power on demand. If you are on the reverse circuit it will only trigger power when you go in reverse.
how is the idea to connect trigger to the tail light while power to the stable power, so when we will put reverse gear camara will be on priority, otherwise we will have the option to select av2 source to turn on the camara
Short and sweet. Thank You
SWEET!!!! Easiest way to tap reverse in older cars. Don't have to trace down a line up front somewhere. Don't have to pull another line all the way up to the front of the bus!!! Only prob I can see might be Running power by low V and speaker lines, but its not like running 4 AWG or something
Hello, so it’s important to connect the ground cable (black) ?
Thank you! I looked through a bunch of videos for what the red cables meant! Even considered not putting in the backup camera because I wasn't sure about the red wire. Thanks!
I connected everything as per the video as I connected the red "power" wire to the "back up" lights. I did that, because the "back up" lights only get power when the car is put into "reverse." Since I only want my rear view camera to work when my car is in "reverse," I thought that this is the logical way to do it. Well, I am getting a "No Video Signal" message on a black screen! Any advice?
Hello, im using a NDDN-W56 toyota navigator and need assist to mount the carvox led 333 reverse cam and i cant see where to connect the reverse trigger red cable. Can you assist? Thank you
So did you get your power from the red 12v wire or did you use the yellow acc?
okey so i dont need that red cable on the yellow rca to get the camera to work ?
Wow I got minds from Ebay plus it's wireless with extra parts I'm 65 do you think I can plug this up myself 😊
Also I thought the red pig-tail was to connect to the reverse on the head screen and the other end to the reversing light as a sort of switch wire so when you put the car into reverse it switch's on the camera.
My problem is when i onn my headlight and i make a reverse the camera not open but when i off the headlight the camera reverse is onn..what is the problem of that..can u answer me sir..thanks
To whom this may concern:
My camera wire doesn't have those 3 little wires , how do I reverse the image?? I'll have a 4 channel Mini MDVR soon and (I THINK) it has image reversing on it?
If I leave out the red wire will the RCA send a signal to the headunit do I need the red wire
On a 2012 ram would u advise splicing the 12v wire and the reverse wire onto the 7 pin trailer plug wires or running both straight to the dash
Wat color is the wire
How does the camera activate when reversing using this wiring method?
It won’t.. this video is going to piss a lot of people off
@@johnarchdeacon4578 My purchase came with everything except the red / black power wires, RCA / video has red pigtails which I wired to to HU correspondent wire, can I tap into reverse power or is the red / black required ?
When you do this, do you typically wire the power wire for the back up camera to the power wire for the radio or do you run it to the battery?
I have red and yellow wires on my video im not sure what to do with the yellow pig tails
helpful video. Thank you