I am only 19 seconds in and I already see a potential explosion. If you have the courage to make BHO never do it around any electrical equipment or anything that can generate a spark. Butane is a very heavy gas and it tends to linger and it can ignite at 35F. The safest way to do this is in a open area away from any electrical wires, outlets or anything else that can produce a spark even static electricity can cause butane to explode
I'm a scientist you should invest in a closed loop system ! Vac oven with a gas recovery system or AKA if you can't afford that go online and buy vacuum purge pump stainless steel Purge pot . You can pull numerous vacuums .. open up the system to allow gas to vent Purge Purge Purge and you don't even have to hit it with the VAC pressure will pull all gases out of your concentrate without affecting any of your terpenes as well as your THC molecules ..
I run bho quite regular I believe the floaties are lipids and waxes from the plant and probably some sugars. And the advice on the unbleached coffee filters and silicone collection container is spot on. And yes too much butane will make your stuff thin also not to mention the evaporation time
Ok so now press the same amount of weed and see the different in yield and then after put the pressed weed in that thing run some butane through it see if theirs difference and then see how much you lose from the press left over.
In between cans, I like to shake up the extractor to make sure everything was soaked and touched by the solvent. Sometimes you can end up with a dry mid section especially if it's kinda packed in there.
Too my knowledge I believe that it is ice water.water forms from either inside with the butane or from the actual tools that hold the leaf material for blasting i.e from being inside the frazer
thats why pre warming the collection dish in a double boiler system with hot water underneath the pan, blast right into that and it boils off as you blast
Those frozen floaties in the extract is most likely water from your bud. If you make a smaller opening or several small openings more pressure will build up inside your extraction tube and literally force the THC infused solvent straight out of the holes. This will make your extraction more efficient.
@@Skunkhunt_42 it's possible but unlikely, especially if one decarbs first. I've been extracting for about a decade now and I've noticed this happens when the bud isn't dry enough, holding too much moisture. I always set my bud out to dry in the air (especially if they have moisture packs) before I extract and noticed that nice, almost "cracker dry" bud, will never have these floaties in it. This is how I've come to this conclusion. It's also frozen which strongly indicates water ice. Something to also keep in mind is that dry bud can also absorb moisture from the air so, if you do an extraction on a day with high humidity, good chance that your bud will absorb some unwanted moisture. And you'll see these floaties but they aren't anything to worry about, they evaporate away.
Hey brother just a tip I like to blast straight into really really hot water on l double broiler set up it cuts down out the evap process and takes less time in the vac purge anyways happy blasting
The stuff floating looks to just be your concentrate! It didn't appear to go away. A huge mat of it got poured into the dish and paper at the end. So idk I'm not a scientist lol lol
These modern vacuum packers have an optional vacuum hose. I wonder if that might not give better taste to draw off the gas rather than force it off with heat. Like freeze drying, kinda😉
dry cracks are only starting at the darker uncured areas...if you gave it 5 times the cure time, dry might be stronger...it's well known that the dryer the wet pour, the stronger it is.
My first attempt i did an oz but it was homegrown stuff. Its difficult getting a quality result without purging it through a vacuum pump. I winterized mine after a day n a half of boiling it off on a waterbath. After a night of constantly replacing the hot water i threw her in the freezer for a bit and that was my finally product. Burnt and tasted like butane badly so i Know i fucked up by not vacuuming it off. O well better luck next time
Now i understand why when i smoke dabs i get that rush like when i used to huff butane. I did it to many times an guess thats why i really didn't get into smokeing dabs i would rather smoke vapes or good bud. Nice video tho. Thanks for sharing. Might try it some time looks like you used a half or more im guessing of course could use that to make some green crack mixed with grinded up weed or hash. An smoosh it together to form a round hard rock that could be smoked with different highs depending on what strains you would happen to use.
My dad was an electrician. I’m not sure if you guys know this, but every outlet no matter if it’s plugged in or not, electricity bouncing in it. That would mean that plug next to the butane. Gas would explode that dish in a second like a firework that dude is crazy to be blasting butane so close to that plug.
I did the 1st part without the vacuum 10 years ago. I would then put it in a vial & use a lighter to boil it. Best oil I ever had. Out of an ounce, I would get around 5-6 grams of potent product. I also used a hair dryer to evaporate all the butane. How many grams did you get from the 2 ounces you used? I did this with my grow at the time & the strain was Northern Lights 5 X Blueberry.....
Had a tube years ago, we would freeze the packed tube before we started and quit putting butane in when it started looking less yellow coming out the end
Usually a couple of hours until the tube was a little frosty, seemed like the runs that we didn't freeze it long enough it just took more butane to chill it down at the beginning
I think if he would have used less butane it would have burned off faster. I have been told that one can is good enough and no more than 2 cans per push
2 cans will only do a Oz really and depends on how many trichromes are on the weed. You need to run gas through till it runs clear. The stuff floating on top of the butane is the fats from the cannabis
Gotta make it run clear or your leaving trichomes in the waste.😢 I personally like all mine out of the waste so however many that takes that's just enough.
You are such a cool guy I agree so much with what you say in your video. You are so right about how people are about selling bulshit weed but they claim it's grade A when you grow your own shit you know that you got great a shit there is so much what you say that I am the same way about, I also want to thank you because you taught me some things in this video, I had no idea how to make dabs, and I did not know that you could eat them in pill form, because that sounds like something like I want to do. That's how I found your video trying to research how to make oil for edibles. Thx friend go get them chickens LOL
I was focusing so hard at what you were doing the rooster 🐓 in the background jump scared me and I thought your butane can was about to explode or something.. 😆 🤣 😂
Try packing it tighter and when the color of thr liquid coming out isn't green stop ading butane oh and most important dont heat over 98 degrees the terps are distroyed at 114 degrees let it evapetate slow the darker the product the better
Soak weed in ipa 1hr strain thru cloth then re strain thru coffee filters then boil down using metal bowl placed in water in electric frypan makes thick oil u can smoke
thats only going to remove whats crashed out of solution....just go about the process as usual but defat/wax the solution afterwards with alcohol, crystal clear oil afterwards and can be forced into certain crayst states, like sap, pull and snap and shatter
Couldn't it be crystallization of some of the desirable chemicals? Chemical devolved in solvent -> solvent evaporates causing precipitation of potentially thc
@@jamesgrix2201 no it wont crash out of solution like that...the fats,waxes,and lipids do first especially with a liquid solution. even when winterizing the THC still doesnt drop out until conditions are met
Definitely want to be careful as the Pyrex will burst sometime or another,use a double boiler type heat larger Pyrex with boiling water and concentrate dish floating in it!!!also try whipping it with a whipping tool(dab tool etc) .
@@grimreaper-fg9xz I put my Pyrex plate on top of a pot of water and let it sit there and the warm water would evap it. And it worked just fine. You can still use the hot plate to evap the left over butane
@@anthonymaize5764 pressure doesnt have much to do with it....super saturation and controlled release of gas is what causes it to crystallize, but yes jars work but break most of the time in my experience, idk if i just cant find the sweet spot or what but a metal pressure chamber i can every time in a few weeks
That butane gas is the most dangerous method for pure cowboys 🤠 easy enough with a teashirt printing press heat induction or u know u can save n buy a nug smasher
Here’s a pro tip. Dont smoke while you’re off gassing butane lol. That’s how that building blew up in Detroit. All those canisters were butane bottles blowing up.
broooooo.....with tubes you gotta "cook it" as i always called it....when you get close to popping through the filter tip the tube upside down with the can in the top still and blast air into it for a few seconds.from the can....then flip back upside down and continue blasting, ive done tests on this with already blasted product and there is almosth nothing left afterwards. vs like how your doing ti i can still make a damn good batch of edibles with your spent bud
I think that stuff is ice mixed with oil the ice came from moisture in the air being frozen like the frost on outside of the tube. I zoomed ahead so did you say anything about decarbing the pot first.
Man my arm holding the tube always got so sore at the 4th can. I'm assuming that's a 100 gram tube from the size, looks like the same one I used to use. I always bent the teeth of a fork and whipped up my extract with it right as it starts getting really thick to de-gas and bring out the terps.
@@bammbamm6869 and if you use a fan that says your broke and cant afford a proper fume hood.....probably shouldnt be blasting with possible sparkes from a fan blowing close to something just as flammable as ether
It's not deadly/toxic when done properly. You need PURE butane. A LOT of high % THC oil in dispensaries is BHO, and it's safe. Cans can be sketchy bc you don't know what the contaminates may be. I like pressed better but the good stuff is pressed from sift or keef. Whereas butane and sometimes CO2 runs can get a similar % THC using flower. BHO made from sift is basically pure THC when done right.
iv dbeen doin it sith butane for 15yrs along time b4 dabs as a slan existed i do it different tho i use a coke bottle (plastic) comes out better then honey ae
I just use a pot with lukewarm water in it then I sit a stainless steel bowl in it then I spray my stuff straight into the bowl by the time I get done almost all of it has already evaporated then I only have to wait a couple minutes for the rest of it to evaporate then I'll hit it with a blow dryer to evaporate anything that is left in it using the air of the blow dryer to move it around that way I don't get that shity butane taste like most people have
Do you really need 4 cans for 60 grams ??? I send mine to be extracted with 2 cans to 2 ounces and it comes out not very much but very potent but I feel as if I may be getting taken ????
I never would've thought smoking weed and making some brownies would one day turn into something that looks like cooking crank. No wonder so many people think stoners are hard core druggies, they're seeing videos like this.
Diamonds also known as THCA is an extremely sophisticated process and shouldn't be attempted by anyone who doesn't know wtf they're doing. And you need a proper blast chamber box since there is a high risk of explosions.
That stuff you was wondering about floating, it could be chemicals added to what they spray the legal weed with, not sure if the buds you used was home grown or store bought but legal weed has chemicals to make the strains
It's the mass of organic material that makes up the final product once fully processed watch as it all combines to make the last stage of actual mass that you smoke .
I am only 19 seconds in and I already see a potential explosion. If you have the courage to make BHO never do it around any electrical equipment or anything that can generate a spark. Butane is a very heavy gas and it tends to linger and it can ignite at 35F. The safest way to do this is in a open area away from any electrical wires, outlets or anything else that can produce a spark even static electricity can cause butane to explode
I know i saw that right off the bat too.
It has a very wide explosion window as far as it’s concentration in air too.
Right when he's like "I got my hot plate at about 100 degrees". I was like "not right now tho right?"
Well outside the gas will rasie to fast in side yes tape your outlets wot duck tap if summer tinfoil windows God was with him this DAY😂😂❤
😂😂😂😂
I'm a scientist you should invest in a closed loop system ! Vac oven with a gas recovery system or AKA if you can't afford that go online and buy vacuum purge pump stainless steel Purge pot . You can pull numerous vacuums .. open up the system to allow gas to vent Purge Purge Purge and you don't even have to hit it with the VAC pressure will pull all gases out of your concentrate without affecting any of your terpenes as well as your THC molecules ..
I run bho quite regular I believe the floaties are lipids and waxes from the plant and probably some sugars. And the advice on the unbleached coffee filters and silicone collection container is spot on. And yes too much butane will make your stuff thin also not to mention the evaporation time
yep exactly what they are insolubles, sucks butane is a bitch to try and dewax with at AP vs iso, or id say just filter it off
Legend also said he is no longer around after lighting up that ole Marlboro red.
I personally like using non bleached coffee filter instead of the screen mesh. It helps block any plant matter that may seep thru
I use both
The contacts on thermostat can spark amd cause an explosion at the hotplate
Ok so now press the same amount of weed and see the different in yield and then after put the pressed weed in that thing run some butane through it see if theirs difference and then see how much you lose from the press left over.
Man, I just got a full dose of nostalgia!
Legend says its still bubbling to this day ...
You watch to much tik tok
? That didn't originate in tiktok your from Gen Z I'm assuming sorry for your loss
@@joshrangel1296 he meant your attention span has become tok'd
@DasGoodSoup sorry never heard of that term either I'm assuming another tiktok trend ?
I’ve heard a 4 year process is the best way to smoke or dab.
In between cans, I like to shake up the extractor to make sure everything was soaked and touched by the solvent. Sometimes you can end up with a dry mid section especially if it's kinda packed in there.
Too my knowledge I believe that it is ice water.water forms from either inside with the butane or from the actual tools that hold the leaf material for blasting i.e from being inside the frazer
thats why pre warming the collection dish in a double boiler system with hot water underneath the pan, blast right into that and it boils off as you blast
This is pretty much the same reason,
why I got interested in learning about chemistry😂
THE STUFF FLOATING AROUND IS ICE
Those frozen floaties in the extract is most likely water from your bud. If you make a smaller opening or several small openings more pressure will build up inside your extraction tube and literally force the THC infused solvent straight out of the holes. This will make your extraction more efficient.
I came to the comments wondering what those floaties were! Thanks!
What if it were thca-monohydrate? The mol ratio of thca:h2o inside the trichome is apx 1:1.....
@@Skunkhunt_42 it's possible but unlikely, especially if one decarbs first. I've been extracting for about a decade now and I've noticed this happens when the bud isn't dry enough, holding too much moisture. I always set my bud out to dry in the air (especially if they have moisture packs) before I extract and noticed that nice, almost "cracker dry" bud, will never have these floaties in it. This is how I've come to this conclusion. It's also frozen which strongly indicates water ice.
Something to also keep in mind is that dry bud can also absorb moisture from the air so, if you do an extraction on a day with high humidity, good chance that your bud will absorb some unwanted moisture. And you'll see these floaties but they aren't anything to worry about, they evaporate away.
@@tarlnobert8033 you're welcome! ✌😄
good info.. But when you say make several small openings are you meaning like pockets in the tube? So not to pack the tube densely
Hey brother just a tip I like to blast straight into really really hot water on l double broiler set up it cuts down out the evap process and takes less time in the vac purge anyways happy blasting
Chemistry is dope!
If you want an easier reclaim method you can use a silicone baking dish as your basin.
i always used a silicone or hard plastic restaurant scraper
@@hugostiglitz4452 you don't need a scraper if the dish you run your butain wash in is made of silicone.
Good tip. Do you take it down to shatter or will it come out when it's still sticky like tar?
@@ElohimYellow i agree but over time the shock of temperature will degrade the silicone over time...glass wont.
Use a silicone bowl stick it in the freezer for 10 minutes when it's done the whole bit comes right out
Amazing Very Cool.
WE USED TO DO THIS IN THE 90s ya we set out dish in a warm dish of water also
The stuff floating looks to just be your concentrate! It didn't appear to go away. A huge mat of it got poured into the dish and paper at the end. So idk I'm not a scientist lol lol
I used to do this 10
Plus years ago. 😊
Great video
These modern vacuum packers have an optional vacuum hose. I wonder if that might not give better taste to draw off the gas rather than force it off with heat. Like freeze drying, kinda😉
A single stage vacuum pump works very nicely
Dude is gonna go to the moon. Literally.
dry cracks are only starting at the darker uncured areas...if you gave it 5 times the cure time, dry might be stronger...it's well known that the dryer the wet pour, the stronger it is.
I have that same blue bowl with the ring😂
Thx, I’ll stick with the cold press
that floating is mold u can spoon it out if u look at it under the micro scope u can see the mold i was having same thing
My first attempt i did an oz but it was homegrown stuff. Its difficult getting a quality result without purging it through a vacuum pump. I winterized mine after a day n a half of boiling it off on a waterbath. After a night of constantly replacing the hot water i threw her in the freezer for a bit and that was my finally product. Burnt and tasted like butane badly so i Know i fucked up by not vacuuming it off. O well better luck next time
If you purge it instead of just holding it doesn’t freeze the bud as much and you don’t have to use 4 cans
Now i understand why when i smoke dabs i get that rush like when i used to huff butane. I did it to many times an guess thats why i really didn't get into smokeing dabs i would rather smoke vapes or good bud. Nice video tho. Thanks for sharing. Might try it some time looks like you used a half or more im guessing of course could use that to make some green crack mixed with grinded up weed or hash. An smoosh it together to form a round hard rock that could be smoked with different highs depending on what strains you would happen to use.
If there is butane left in your product it will taste like you put a bar of soap in your mouth after a hit. Just fyi
~ZJAK
What is u on about
Ah butane. I can feel the headache with every hit now
My dad was an electrician. I’m not sure if you guys know this, but every outlet no matter if it’s plugged in or not, electricity bouncing in it. That would mean that plug next to the butane. Gas would explode that dish in a second like a firework that dude is crazy to be blasting butane so close to that plug.
you remind me of the guys I would play call of duty with when I was a little kid
i got a quarter of resin the other day ago for 45 bucks. and never had to risk blowing my self up.
That's da cook off yellow stuff at the top 🔝
Same way we do it in N.Z
Am i the only one that noticed this dude only uploaded one video after this one 3 years ago. Feds ran up on his ass lololololol
Put the baking dish in a hot water bath. Much safer and more effective
The stuff floating is the outer membrane of the trichomes
I did the 1st part without the vacuum 10 years ago. I would then put it in a vial & use a lighter to boil it. Best oil I ever had.
Out of an ounce, I would get around 5-6 grams of potent product. I also used a hair dryer to evaporate all the butane.
How many grams did you get from the 2 ounces you used? I did this with my grow at the time & the strain was Northern Lights 5 X Blueberry.....
Put a fan above your ventilation to prevent your body from taking in oxygen
Had a tube years ago, we would freeze the packed tube before we started and quit putting butane in when it started looking less yellow coming out the end
how long would you freeze the packed tube?
Usually a couple of hours until the tube was a little frosty, seemed like the runs that we didn't freeze it long enough it just took more butane to chill it down at the beginning
@ozCurt hope it helps man, good luck
I think if he would have used less butane it would have burned off faster. I have been told that one can is good enough and no more than 2 cans per push
2 cans will only do a Oz really and depends on how many trichromes are on the weed.
You need to run gas through till it runs clear.
The stuff floating on top of the butane is the fats from the cannabis
I’ve been told means u don’t kno shit
1 can per ounce usually is good enough depending on how tight its packed how easily it flows tube size all come into play
Wow drink it.
Gotta make it run clear or your leaving trichomes in the waste.😢
I personally like all mine out of the waste so however many that takes that's just enough.
i make same verry good system
You are such a cool guy I agree so much with what you say in your video. You are so right about how people are about selling bulshit weed but they claim it's grade A when you grow your own shit you know that you got great a shit there is so much what you say that I am the same way about, I also want to thank you because you taught me some things in this video, I had no idea how to make dabs, and I did not know that you could eat them in pill form, because that sounds like something like I want to do. That's how I found your video trying to research how to make oil for edibles.
Thx friend go get them chickens LOL
I was focusing so hard at what you were doing the rooster 🐓 in the background jump scared me and I thought your butane can was about to explode or something.. 😆 🤣 😂
Lol!😂
Where do you get the filters for tube from
Always wondered if butane had benzene in it as does gasoline, Benzene is a known Carcinogen
Not unless it’s been subjected to 900 degrees at some point
Try packing it tighter and when the color of thr liquid coming out isn't green stop ading butane oh and most important dont heat over 98 degrees the terps are distroyed at 114 degrees let it evapetate slow the darker the product the better
are you refering to the end product or how saturated the liquid is???
Soak weed in ipa 1hr strain thru cloth then re strain thru coffee filters then boil down using metal bowl placed in water in electric frypan makes thick oil u can smoke
One arc from that plug in..
The floaters I believe are the bad waxes probably get a better product if you scoop those out
thats only going to remove whats crashed out of solution....just go about the process as usual but defat/wax the solution afterwards with alcohol, crystal clear oil afterwards and can be forced into certain crayst states, like sap, pull and snap and shatter
@@hugostiglitz4452 defat the solution? Please expound
Couldn't it be crystallization of some of the desirable chemicals? Chemical devolved in solvent -> solvent evaporates causing precipitation of potentially thc
@@jamesgrix2201 no it wont crash out of solution like that...the fats,waxes,and lipids do first especially with a liquid solution. even when winterizing the THC still doesnt drop out until conditions are met
All the money you end up having in butane in a year you could have a really nice press. Probably not even a year depending on how often you do this
That was very helpful. Going in business. Lol. I wish. Gotta get a roaster. Ty my dab friend....
Definitely want to be careful as the Pyrex will burst sometime or another,use a double boiler type heat larger Pyrex with boiling water and concentrate dish floating in it!!!also try whipping it with a whipping tool(dab tool etc) .
That's impressive! Glad you had the sense to process that outdoors ... the explosion comments are pretty unnecessary. Cool! Pete 🏴
I never used a hot plate I just used water to evaporate it and it works just fine.
How do you use water tk evaporate water
@@grimreaper-fg9xz I put my Pyrex plate on top of a pot of water and let it sit there and the warm water would evap it. And it worked just fine. You can still use the hot plate to evap the left over butane
If you put some in jar with a lid on it and open it once in awaile you will make thc diamonds (90%+ purity and the rest is terpenes).
Yeah it dont work like that
@bylly nallee actually it does you create thc crystals with presure fact check me.
@@byllynallee9238 th-cam.com/video/Z7XZ7hcg8bk/w-d-xo.html
@bylly nallee you don't take all the butain out of the material when you put it in a Mason jar so it will gain presure.
@@anthonymaize5764 pressure doesnt have much to do with it....super saturation and controlled release of gas is what causes it to crystallize, but yes jars work but break most of the time in my experience, idk if i just cant find the sweet spot or what but a metal pressure chamber i can every time in a few weeks
That butane gas is the most dangerous method for pure cowboys 🤠 easy enough with a teashirt printing press heat induction or u know u can save n buy a nug smasher
You sounded like bubbles from trailer park boys in some parts of this video
very true one can is all you need , this is complete over kill!
Here’s a pro tip. Dont smoke while you’re off gassing butane lol. That’s how that building blew up in Detroit. All those canisters were butane bottles blowing up.
Luiaa bro 🍻🔥
That was a Demon 😂
broooooo.....with tubes you gotta "cook it" as i always called it....when you get close to popping through the filter tip the tube upside down with the can in the top still and blast air into it for a few seconds.from the can....then flip back upside down and continue blasting, ive done tests on this with already blasted product and there is almosth nothing left afterwards. vs like how your doing ti i can still make a damn good batch of edibles with your spent bud
the stuff in your gas is just ice i tried to take it out but found it was ice so now just leave it to melt at end
I think that stuff is ice mixed with oil the ice came from moisture in the air being frozen like the frost on outside of the tube. I zoomed ahead so did you say anything about decarbing the pot first.
wondering if those magnetic stirers used by chemists would help constantly stirring it while being reduced on the hotplate
Electric hotplate
I myself used to stir mine a lot and I believe it helps 😁
We call this honey in the UK 🇬🇧
Man my arm holding the tube always got so sore at the 4th can. I'm assuming that's a 100 gram tube from the size, looks like the same one I used to use. I always bent the teeth of a fork and whipped up my extract with it right as it starts getting really thick to de-gas and bring out the terps.
If you're gonna play with butane, avoid any spark risks.
Frrr u can here the lighter in the background😂 making me nervous
Nice
I thought you put a fan on it and it evaporates super fast. My buddy from Cali did it like that at there shop in Humboldt.
Yes you are correct, that's how we do it in Cali...plus you want to push that butane away from you. It lessen the chance of something bad happening 🔥
Yes you are correct, that's how we do it in Cali...plus you want to push that butane away from you. It lessen the chance of something bad happening 🔥
@@bammbamm6869 you sound like a hood chemist.....keep it away from spark and flame outside over a hot water bath.......wheres your risk there
@@bammbamm6869 and if you use a fan that says your broke and cant afford a proper fume hood.....probably shouldnt be blasting with possible sparkes from a fan blowing close to something just as flammable as ether
@@hugostiglitz4452 bro, I was talkin about the old days
Just use a press bro that stuff is fkn deadly
Yes sir live rosin babayy
It's not deadly/toxic when done properly. You need PURE butane. A LOT of high % THC oil in dispensaries is BHO, and it's safe.
Cans can be sketchy bc you don't know what the contaminates may be. I like pressed better but the good stuff is pressed from sift or keef. Whereas butane and sometimes CO2 runs can get a similar % THC using flower. BHO made from sift is basically pure THC when done right.
@@FlyingPusssyfoot when done right…
@@weedismyreligion to be fair I wouldn't use this video as a tutorial lol
@@FlyingPusssyfoot 🤣👍
Just out of curiosity how much flower went into that tube and is it ground or whole flower?
I think he mentioned 60 gr in the beginning.
How much did you use?
Glad that butane can didn't blow up that was laying by the grill
The static spark from the control knobs has caused lots of fires for lots of people. Even direct sunlight outside can cause fires. This is all bad!
You should look into getting a pair of insulated ninja brand gloves your hands will thank you
The material is prob doing a phase change state.
iv dbeen doin it sith butane for 15yrs along time b4 dabs as a slan existed i do it different tho i use a coke bottle (plastic) comes out better then honey ae
That’s upload to you city folks
Nothing like a $20 oreo!lol
Or a 25$ single macaron.. 😱
I just use a pot with lukewarm water in it then I sit a stainless steel bowl in it then I spray my stuff straight into the bowl by the time I get done almost all of it has already evaporated then I only have to wait a couple minutes for the rest of it to evaporate then I'll hit it with a blow dryer to evaporate anything that is left in it using the air of the blow dryer to move it around that way I don't get that shity butane taste like most people have
Why the butane??? I thought the best way was to get two pieces of scotch paper and throw bud inside then press with two hot sides
Do you really need 4 cans for 60 grams ??? I send mine to be extracted with 2 cans to 2 ounces and it comes out not very much but very potent but I feel as if I may be getting taken ????
GOOD SHIT MY GUY
,nice roster
Oh crap.. lmfao. My chickens 🐔 are out ..😂😂😂😂😂
Thanks for the dab lesson. Never done that before but might try. I grow my own here in Maine and it's legal.
Please dont just buy a press
If its legal im sure ypu can buy a press and dont have to go and fuck your shit up with some butane my guy
Don’t try it that shit is mostly butane
If anything in the area sparks youre now on fire
You're in Maine. Have somebody process it for you. Trust the professionals.
I never would've thought smoking weed and making some brownies would one day turn into something that looks like cooking crank. No wonder so many people think stoners are hard core druggies, they're seeing videos like this.
Almost everything about smoking dabs is the same as smoking meth the only difference are the highs are opposite 😂
Did you grind up your bud before hand?
I was told to make sure leaves or product to be dried beforehand
It's water left in the can when they water it down
I'd like to learn the other methods for making shatter wax diamonds I've seen the smashing buds for rosin and I make ice water bubble hash and bho
Diamonds also known as THCA is an extremely sophisticated process and shouldn't be attempted by anyone who doesn't know wtf they're doing. And you need a proper blast chamber box since there is a high risk of explosions.
You can turn the hot water on in the bath tub and just let the dish sit in the tub far enough away so the water doesn't splash in the dish
Place the glass tray in warm water the gas will evaporate faster.....
Medda-Honey!!
That stuff you was wondering about floating, it could be chemicals added to what they spray the legal weed with, not sure if the buds you used was home grown or store bought but legal weed has chemicals to make the strains
Huh?
Have the plants been flushed properly
Mmmmmm
Its not, it is ice.
It's the mass of organic material that makes up the final product once fully processed watch as it all combines to make the last stage of actual mass that you smoke .
I'd rather just smoke 😂
Fr 😂
I feel you for real, who wants to smoke gas? Especially butane as a lighter.
Hey wondering if anyone could help me out is there a way to do this without a vacuum chamber
The butain is the buzz not the weed when you add cems it’s over