How to Replace Passenger and Drivers Side Blend Door Actuators 2007-2013 Chevrolet Silverado
ฝัง
- เผยแพร่เมื่อ 13 พ.ย. 2022
- Buy Now!
New Door Actuator from 1AAuto.com 1aau.to/ib/DMBMX00001
This video shows you how to install a new blend door actuator on your 2007-2013 Chevrolet Silverado. If the air temperature does not seem to respond at all to changes you make in the heat or AC settings, the blend door may not be opening or closing properly due to a faulty actuator.
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
Tools you will need:
• 10mm Socket 1aau.to/oaI3/1AXAA00017
• 5.5mm socket
• 7mm Socket 1aau.to/oaI3/1AXAA00017
• Trim Tool Set 1aau.to/oS5/1AXXX00006
• Socket Extensions 1aau.to/oaY3/1AXAA00015
• Magnet - Extendable
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - ยานยนต์และพาหนะ
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
I just repaired my A/C automatic blend motor assembly by disassembling the unit, inspected the gears, inspected the large final drive gear and its copper fingers that slide on the variable resistor pad. I put more tension on the copper fingers and used the surplus lube from inside and applied it to the gears. Reinstalled the unit and started my 2012 GMC Sierra with the A/C on, varied the temp setting cold to hot and back again, IT WORKS! Just my time and no parts.
This video is EPIC. That camera angle in the upper dash was insane. Thank you for this. I need to do this on my Avalanche soon.
That was some really good camera work. Really tight workspace and great shots of work being done
Love the video I just did this job today. 3/23. Man I would buy you dinner. Thanks for the help
which door controls the hot air mix ?
Is the driver side one that you are taking out at the beginning of the video? Is that where I would find it on a 2009 Chevy Avalanche would be on the passenger side on the floor next to the sub?
Thankyou for the video. Very helpful 🇺🇸🤘🏴☠️✌️
Thank you God bless you 🙏🏼
2007 yukon
I saw two Actuators under the airbag and one under console and one under the steering wheel. Total of 4 .
Great video
The 2009 single zone system isn't located here.... is it behind the glove box ?
Will be the same procedure for Escalade 2009?
Thanks
2010 3.9 v6 chevy impala, driver side vents not blowing cold like the passenger side. Replaced driver side actuator hoping to fix the issue. Still having the same issue. Did 3 different reset/relearn procedures, still same issue... Any ideas? Could freon level be low? Any help is most appreciated!
2014 Yukon, was replacing the actuator under the dash, and the little "protective" panel for the actuator doesn't seem to do much, but really makes things tougher to R&R the actuator. Visible at 2:57 time/mark. Can this simply be cut off, or what does it really do???? Thanks.
your milwaukee battery is almost dead buddy. useful info
Please do this for a Toyota Tundra, same years.
How do you know if it is the actuator, blower motor or flap? If you are trying to do this yourself? Would you have to take them all out?
My problem is the air and odors they are coming from outside and just one time I have the problem of mixing cool air on the driver side and hot air on the pass side I need to replace the acuator on the bottom or the one close to the air bag?
If the truck is blowing hot air out on both sides and the driver side randomly blows cool/room air temp, would this be the problem? Turned heat down all the way and turned it back up twice, and heat began blowing out both sides again.
This work for Chevy tahoe and for what is the acuator close to the air bag ?
How long does the battery need to be disconnected?
I have tahoe 2008 there is sound coming from gages like click click and mileage number coming blinking .
What mean? What the issue
Just worked on my 2010 Chevrolet 1500 Silverado. Drivers side actuater went in just like the video. The passenger side dash on my truck is totally different air bag set up. HELP!
I have a 2008 Chevy Tahoe LTZ which one is the one that lets cold air inside the car
Which one allows the ac to enter . I see 4 of them in my car
This is to fix the ac? Cuz my suburban blows air from the back vents and the system is turned on like I can change the temperature and all that
it just it won’t blow air from the front vents and I’ve been looking at tons of video but I just wanna make sure that’s what it’s for
I’m very new to cars
What happens if you changed and it was blowing cold then you turn the car off and it's back to doing the same thing ? The driver side is back to blowing heat
Did u really say 5.5 mm socket? Smh