Nice Work! I am in the middle of doing this to flare a grey sewage pipe but did not have a smooth surface to push it on, so it split and collapsed. Now I found a smooth surface to push it on. I wanna flare it from 110 - 160mm to fit my existing kitchen fume extractor fan on it and keep it in the attic where it makes less noise.
Thanks for the great demonstration,is it ok to use 2 pieces of inch and a half pipe instead of one piece of four inch ? i dont have enough space the 4 inch.
So if I say have a port length of 12 inches that would set my tune once I stalled unflared , but then I went to flare l both ends , would that effect the tuning now having flared ends ? Not sure if this little change effects tuning if any or at all . Because to me seems it could effect it because of the preset length determine the frequency ...just. question I had
If you add flares to the 12" pipe, like using epoxy, it will not change the tuning. If you flare the ends of the 12" pipe, its not going to be 12" any more. It might be 9" and that changes the tuning. Rule of thumb is that flares are not counted as far as port length is concerned.
I like the process of flaring the port like this. I thought about adding some upright pieces to 4 sides of the lazy susan to keep the mold from sliding off when you were heating/spinning the port.
Is that a sheetrock jack in the background? Also I have asked others this question a not got a response.. Can I run 2 Taramps Smart3k's to a common chamber 4 12''s. Two on each amp. If so how there is no phase adj.
AMICUSTOMS Whats better a L port box or Aero port box and does wattage and size of sub matter for each type of box, like is one better for lower wattage system or higher wattage system?
I want to build a class 4 box that fits on the rear deck of a 2004 grand marquis. I want the port tuned as low as possible. I love a low end monster. and I want it pass thru the rear seats arm rest so the bass will only enter the cabbin (no trunk rattle). I want to use 4 sundown audio 8". my questions are with the airspace , and a is port possible for the build. well over all is it possible to build and if so any possible combinations that will accomplish the job will be appreciated.
i used an aeroport calculator and it says i need an 8 inch port. does it mean that my port length including the flares from end to end needs to be 8 inches?
I use term-lab and it says to use a 6x10.25 flared port. Do I cut 10.25 and them flare it? Also does the flare have to be the same size on each end? Great video by the way.
Brother love the video, can u please please tell me how many inches extra would i have to add to my length of port for this? Thank ahead of time & thanks for video bro.
I do have a question.. is it absolutely necessary to partially aero flare the opposite end of the pvc for a sub box on the end that goes into the box ? I never knew that is there any gain or loss to doing that
Does the length and diameter of the port affect the sound? Is there a way to calculate how lone the tube needs to be or do you just tune your amp to get the right sound?
I think that using his rule of thumb for the tube and round over radii is just a short cut to ensure you have approximately/at least double the cross section area at the flared end compared to the basic pipes area. Thats just my guess though
+Sebastian Williamas Aero increases efficiency as it allows the air to exit smoother and faster. Yes it affects the tuning you have to add length due to the flare.
So friend, not even the RE told me the duct's measure to tune the box, like length and diameter, the model of my subwofeer is RE SEX 10D4 V1, the manual says to make a box dutada of 35.4 liters plus the duct, could help me?
@@AMICUSTOMS please keep making videos your videos are very useful and important to people that do want to learn more information I follow from Canada 🇨🇦 #YSW
@@AMICUSTOMS yes building more speakers boxes for car audio what about home theater systems boxes i follow you 💯 from 🇨🇦 #YSW keep up all of your great work you are doing
Good process but i do notice its not a even flare for a flat surface. Id suggest a taller center on the mold to keep it from wobbling or a exterior brace to go up higher around the outside to keep it centered at you press the mold
Was hopin to see u at slamology andy! will u be attending any shows this year within a 3 state radius of Pennsylvania? the Carolinas are kinda pushin it for me..12hr drive. but id doit if I knew u b there.
flares may look pretty but builders must keep in mind that any flare design will not affect the bass output quality, its simply for cosmetic appearance
could u give me some box advice for a dd redline 800 18.. pretty similar to hdc4. long story short I've made 2 boxes.. 1 6.75 cuft after port and sub and 110sqin of port 24in long.. kills lows 171.1db at 44hz. box 2 5.2cuft after displacement 19.5sqin of port per cube, 18in long.. sounds loud as shit but did a 146.9 at 48hz. in a bravada at cab I believe is 44hz so why is my "spl" box down on score... need some help
Hey man quick question. I'm going to build a under seat front facing box for my 08 Silverado for 4 soundqubed 8's. Probably going to lift my seat 3 inches to make room for the biggest box possible, what size aero port do you recommend? And what length?
Something like that longer ports tune to a lower frequency but you have to have calculated the box volume with its bracing, subwoofer and port installed. Also taking note that the subwoofer or subwoofers can play at the that frequency safely. There are apps called box calculators that do mostly all the above for you.
Thanks for posting never thought it would have melted or molded as easily as it did great work
Nice Work! I am in the middle of doing this to flare a grey sewage pipe but did not have a smooth surface to push it on, so it split and collapsed. Now I found a smooth surface to push it on. I wanna flare it from 110 - 160mm to fit my existing kitchen fume extractor fan on it and keep it in the attic where it makes less noise.
Thanks for the great demonstration,is it ok to use 2 pieces of inch and a half pipe instead of one piece of four inch ? i dont have enough space the 4 inch.
What do you think about having the port towards the driver side? Is it supposed to be twice as loud? Or
If you flare both ends, how do you get it in the box? One end has to be smaller than the other
Yes onensode is slight smaller than the mounting port diameter
So if I say have a port length of 12 inches that would set my tune once I stalled unflared , but then I went to flare l both ends , would that effect the tuning now having flared ends ? Not sure if this little change effects tuning if any or at all . Because to me seems it could effect it because of the preset length determine the frequency ...just. question I had
If you add flares to the 12" pipe, like using epoxy, it will not change the tuning. If you flare the ends of the 12" pipe, its not going to be 12" any more. It might be 9" and that changes the tuning.
Rule of thumb is that flares are not counted as far as port length is concerned.
What’s better aeroport or side port ? It’s for a 8 inch massive hippo
Awesome work brother!👍👏
I like the process of flaring the port like this. I thought about adding some upright pieces to 4 sides of the lazy susan to keep the mold from sliding off when you were heating/spinning the port.
Is that a sheetrock jack in the background? Also I have asked others this question a not got a response.. Can I run 2 Taramps Smart3k's to a common chamber 4 12''s. Two on each amp. If so how there is no phase adj.
Bud, do you have a 10" aero port laying around, need it to be 17 " long...
I'll buy it of course...
Koool, I'll be attempting my first aero ports box. Doing 4 6" ports for 3 15s..To buy 4 6" would cost me 150 bucks..Thanx for the info.
AMICUSTOMS Whats better a L port box or Aero port box and does wattage and size of sub matter for each type of box, like is one better for lower wattage system or higher wattage system?
Thick walled pvc works great, I built one today.
What u use to do it?
@@johnkintner1637 heat gun and doggie bowl
I want to build a class 4 box that fits on the rear deck of a 2004 grand marquis. I want the port tuned as low as possible. I love a low end monster. and I want it pass thru the rear seats arm rest so the bass will only enter the cabbin (no trunk rattle). I want to use 4 sundown audio 8". my questions are with the airspace , and a is port possible for the build. well over all is it possible to build and if so any possible combinations that will accomplish the job will be appreciated.
when building a bandpass subwoofer box is it better to have ports or slots & should it be larger on the outside or does that matter?
Reverend Timothy Petrey really depends on the design there isn't a one size fits all answer to this question.
I wonder if I can do that with jb weld or something like that instead of that expensive looking stuff he used?
What he used is cheaper
Awesome video came across this channel late in my life.
Also what speakers were you making this the blue ones in the end of video looks nice was brief
Hi, Which gives better performance in SPL, aeroport or long vents? thanks..
i used an aeroport calculator and it says i need an 8 inch port. does it mean that my port length including the flares from end to end needs to be 8 inches?
Do you think this would work with PP pipe aswell? PP is the most common material where I am from
I use term-lab and it says to use a 6x10.25 flared port. Do I cut 10.25 and them flare it? Also does the flare have to be the same size on each end? Great video by the way.
Brother love the video, can u please please tell me how many inches extra would i have to add to my length of port for this? Thank ahead of time & thanks for video bro.
That’s awesome! Thanks for the tip
I do have a question.. is it absolutely necessary to partially aero flare the opposite end of the pvc for a sub box on the end that goes into the box ? I never knew that is there any gain or loss to doing that
While it's not absolutely necessary, it reduces port turbulence/chuffing noise.
@garrettrichards5559 just line it with self adhesive felt, hobby lobby
Nice video. Thank you for sharing.
question if you have a 3 sub box, three chambers inside, would I need to put a port in each chamber???
if each chamber is sealed off from one another, then yes you'd need 3 ports
Drew Rogers thanks man appreciate it
np, good luck on your build
Would shortening an aeroport lower or raise the tuning frequency?
Tee it would raise tuning
thank you!
Where did you find the thin walled pvc? Can't don't it anywhere
+james55975 There's schedule 40 and class 200. Class 200 is what you want, which is what he used. Call an irrigation store.
Does the length and diameter of the port affect the sound? Is there a way to calculate how lone the tube needs to be or do you just tune your amp to get the right sound?
I think that using his rule of thumb for the tube and round over radii is just a short cut to ensure you have approximately/at least double the cross section area at the flared end compared to the basic pipes area. Thats just my guess though
The length and diameter determine the tuning. It’s a science. I do not suggest guessing at it.
Ithis is what i visioned. Thank u
I think that you should try a thicker PVC pipe for more resonance.
how does an aero port differ from a regular port. also does the flared ends affect the tuning.
+Sebastian Williamas Aero increases efficiency as it allows the air to exit smoother and faster. Yes it affects the tuning you have to add length due to the flare.
Thanks
Thank you for all you do bro!
Do you really need to flare the other end? If so reason.... Ty
Lower mach percentage....smoother air flow, no port noise (assuming you have the proper diameter)
easy, efficient and effective, my kind of diy
So friend, not even the RE told me the duct's measure to tune the box, like length and diameter, the model of my subwofeer is RE SEX 10D4 V1, the manual says to make a box dutada of 35.4 liters plus the duct, could help me?
Nice idea bro very useful atleat for me, .......love you bro from INDIA.
andrew, whats your thoughts on aero vs slot ports. i got 2 hdc3 15s and ampere 3800 and i wanna get the most clean low bass with ability to hairtrick.
My view is under 10 cubes box should run aero, over 10 cube do slot port. That is what I have done and tested and seems to be the cut off.
@@AMICUSTOMS please keep making videos your videos are very useful and important to people that do want to learn more information I follow from Canada 🇨🇦 #YSW
@@AMICUSTOMS yes building more speakers boxes for car audio what about home theater systems boxes i follow you 💯 from 🇨🇦 #YSW keep up all of your great work you are doing
Excellent video vlog and how to make areoports
You cut out the circles with a jigsaw? How the heck you get them so perfect?
Also where did you get the pipe? I can't find those ANYWHERE!!, I've called like 10 places, searched online, etc
Wow, yours is bigger than mine..
your heat gun that is. Holy massive heat gun! What's it's rating?
i use a heatgun and a metal mixing bowl
Where’s the best place to buy pipe this thin??
nice video! thanks for the info!
Very clever! Thumbs up!
Fkng outstanding!👍👍👍👍👍
Are you still helping people with their configurations of subwoofer I can use a little help tuning my custom box I mean I'm not totally green
Do you still make three areo ports
Cool video thanks for the tips that box is awesome to 👍🏼👍🏼✌🏼💪🏼🔈💪🏼🔉💪🏼🔊
Hi buddy do you sell aero ports? I would like to buy two in 5" x 20" ports if you do sell.
any hints or tips or follow ups from this video boss?
Net aero port or without net airoport please give answer
Good process but i do notice its not a even flare for a flat surface. Id suggest a taller center on the mold to keep it from wobbling or a exterior brace to go up higher around the outside to keep it centered at you press the mold
Incorrect but thanks for the feedback the flare is even, and the mold works fine I have made dozens of flares with this same mold no issues.
@@AMICUSTOMS the tube standing on the table looks uneven and tilted
@@stevenb320 it might look it but it isn’t, the flare is even
Was hopin to see u at slamology andy! will u be attending any shows this year within a 3 state radius of Pennsylvania? the Carolinas are kinda pushin it for me..12hr drive. but id doit if I knew u b there.
I will be giving this a try
where can i buy this thin walled PVC, cant find that here in NYC
BOB carvey what bout Home Depot or lowes???
no you cannot buy it there.
BOB carvey. do u have True Value hard ware store or a 84 lumber???
@BOB carvey there are also online retailers but like the other people said, a hardware store is the cheapest and fastest option.
yes i have true value store
thats pretty cool of making an aero port. thanks.
have you ever heard of the bumpboxx?
flares may look pretty but builders must keep in mind that any flare design will not affect the bass output quality, its simply for cosmetic appearance
That's awesome!
AMICUSTOMS awesome video. Keep these up please that was helpful
Is this thin wall pvc?
How do you size the port for a box?
Whats the box going in.
2011 f150 under the rear seat
could u give me some box advice for a dd redline 800 18.. pretty similar to hdc4. long story short I've made 2 boxes.. 1 6.75 cuft after port and sub and 110sqin of port 24in long.. kills lows 171.1db at 44hz. box 2 5.2cuft after displacement 19.5sqin of port per cube, 18in long.. sounds loud as shit but did a 146.9 at 48hz. in a bravada at cab I believe is 44hz so why is my "spl" box down on score... need some help
147.1db on 1st box*
+chris jones needs more port area on the SPL box
AMICUSTOMS 20sq in per cube isnt enough?
If not what should i try? 5 cuft after displacements with 24sqin per cube tuned to 40hz or what would u suggest
I use PAM non-stick cooking spray, when baking ports.
What song is that, at the end of your video?
8
Where are u located can u make m3 3 5 in 13 long
Great idea. Thanks
amicustoms i would like to ask a question if you don't mind?
carlos espinoza ok
AMICUSTOMS hey man question if you have a 3 sub box, three chambers inside, would I need to put a port in each chamber???
Bob EVANS yes
nice work mate that is helpful
single cab truck box?
Quad cab ford rear front fire under seat box.
song at the end ?
Saludos desde Colombia y gracias por tomarse parte de su tiempo en enseñarnos parte de su saviduria
Good !!🤝
good explain,
Great video thanks. Can you design a mould for me?
Good video man nice work
So cool! Thanks brother!
Nice video, do as many of these as you can
Hey man quick question. I'm going to build a under seat front facing box for my 08 Silverado for 4 soundqubed 8's. Probably going to lift my seat 3 inches to make room for the biggest box possible, what size aero port do you recommend? And what length?
6 inch aero about 20 inch long
should have some clamps to hold while you turning it to make the port so it wont slide around if that makes sense
Whats the name of the song at the end of the video?
The longer the pipe the Deeper the bass?
Something like that longer ports tune to a lower frequency but you have to have calculated the box volume with its bracing, subwoofer and port installed. Also taking note that the subwoofer or subwoofers can play at the that frequency safely. There are apps called box calculators that do mostly all the above for you.
Nice vid man thanks
Awesome technique , keepum coming
Nice I knew there was a way to do that
Can you make one for me?
Pretty cool man 💪🏼💯👌🏼
Nice thanks!
Wonderful! Thanks!
Thats perfect bro
Oh yeah ,love that mold
Awesome
i like the box looks biutiful men
Is a areo port is better than regular port
Thanks for sharing.
Dude where are you...why no more videos
jmar662 jmar662 I am still putting up vids, just been busy building SoundQubed’s demo van for them.
AMICUSTOMS will you be loading videos of the build
Thanks , that is a great way to do a flare on a port thanks for the info , ...
muy buen trabajo