Oh man you are real hero, you save my ass, Right after first ride I tried to unlock max speed and I mess up all setting and everything stops working, now it's working again and I can reach about 42km/h on Phnholun P20
P01: Jasność LCD/LCD brightness P02: 0: KM; 1: MILE; jednostka prędkości mile/kilometry P03: 24V, 36V, 48V, 60V; napięcie baterii (służy tylko dla wskaźnika LCD bar battery) (LCD battery level only) P04: czas uśpienia w minutach (domyślnie 10minut) - czas wyłączenia roweru przy bezczynności; sleep time P05: PAS number selection: 0, 3 file mode: 1,5 gear mode: ilość trybów PAS, albo 1-3 albo 1-5 albo 1-9 P06: Wheel setting inch: rozmiar koła w calach P07: Speed gauge magnetic steel number: range: 1-100; ilość magnesów na kole do pomiaru prędkości? P08: Speed limit setting: ograniczenie prędkości - 100 brak ograniczenia P09: zero start, non-zero start setting： 0: zero start; 1: Non-zero start; ? konfiguracja manetki gazu? P10: The drive mode is setting： 0: Power Drive; 1: Electric drive 2: Power Driven and Electric Driven Coexistence; konfiguracja manetki gazu? P11: Help sensitivity setting：range: 1-24; czułość wspomagania P12: Help start intensity setting：range: 1-5; intensywność wspomagania podczas ruszania tzw "kop" P13: Power Magnetic Steel Disk Type Setting： 5, 8, 12 Magnetic Steel Types; parametry silnika, nie zmieniać bo przestaje wspomagać P14: Controller limit value setting：range: 1-20A ; limit prądu kontrolera, nie zmieniać P15: Controller undervoltage; napięcie minimalne wyłączenia, dla baterii 36V ma być =29V dla baterii 48V ma być =39V P16: ODO zero setting： length press key 5 seconds ODO zero; resetowanie przebiegu roweru P17 :Automatic cruise optional：0: No enabling cruising, 1: enabling cruising; tryb tempomatu (musi być zaprogramowany żeby działało) P18: Display speed ratio adjustment： range: 50 % ~ 150 %, korekta wyświetlania prędkości, domyślnie 100% P19: Zero PAS selection： 0: 0 file, 1: does not include 0 file; w trybach PAS można wyłączyć tryb 0 - brak wspomagania P20 :0:2 Protocol 1:5 S Protocol 2: Standby 3: Standby ??? Ustawienia bardzo podobne w wielu modelach M6C LCD, nie ruszać P13 bo przestaje wspomagać
Are PO8 and P13 used for spped control? I am looking at buying a bike with this display. If PO8 is used for setting the power to the motorI am not sure how you set it to the nominal or peakpower of the motor. I would simply set it to the expected km the motor shoul push?
Update Ron" i found that the Battery has movement [lateral ] this has caused the terminals to burn, [this explains the E06 /08 fault] i have clamped it tight, its solved the problem, but need new teminals, them silly 2 pin hole type are burnt,
Aye ron" my display M5 needs repaced, the switch on the bars broke, tried Shengmillo theres had a short cable with round plug, mine is long full lenth square 5 wire, explained this ,but no joy,. so bought a aftermarket from chine ,see how it goes wen arrives,
@@RonWalkerCairngormGuides Bikes been good, 480miles, apart from error 8./6. sometimes, this is connections just need split and cleaned, ,dry days are here ,so need the switch gear, etc,,[ i can link out the broken switch, to get it running,] ,but its not ideal,
My peddle assist was working great....just got the bike. Now it's now working! I've checked settings several times, any suggestions or advice? Thank you for your video
@RonWalkerCairngormGuides I got a senada drifter 500 watt and holy snaps man I messed it up and it was capping at 20 followed ur steps and this thing goes 35 holy crap man seriously thank u do much I subscribed ❤❤❤❤❤❤❤❤❤
@@RonWalkerCairngormGuidesis the speeds accurate cuz I change PO 18 it was on 100 and on 150 my bike says it goes 42 mph is the speed accurate hope u get back to me if not I got a speedometer in my town I'm gonna check tonight I really hope it's accurate
Last week I received my MX02s very happy with it. But after going through the settings and changing the PAS mode to 9 and back to 5 I cant reach PAS = 0. Now it by default start with PAS 1 and if I go down it stays on 1. So basically I only have PAS 1,2,3,4,5 or 1,2,3,4,5,6,7,8,9
@@RonWalkerCairngormGuides How can I set the throttle twist grip to only support me up to 6 km/h when starting? And how do I reduce the maximum speed to 45 kmh, like with an S Pedelec?
Set P08 to 25, the speed limit is in kilometres. You can set the speed limits anywhere from 1-100. 100= no speed limit for off-road only and 25 kilometres is the EU and UK legal speed limit which is equivalent to the UK's 15.5 mph.
@@RonWalkerCairngormGuides Thank you very much. I've just done that, but for some reason, 25 = 12mph (throttle - testing indoors). I set it to 32, and it's now about 15mph. PAS 2 - 5, throttle hits 24mph.
@@emadmoussa2576 have you tried P18 the speed offset, the throttle settings are different from pedal assist, you can turn off the throttle to stay legal in the UK?
@@emadmoussa2576 If you set P10 to one you can turn off the throttle and just have pedal assist. I now have my bike set to just 3 PAS rather than 5 and use just 1 or 2 most of the time. The higher settings and speeds just gobble up the battery!
I have a fortis electric bike and my settings only go to 17. Can you please help me to restore factory settings. As they have been changed and now my bike doesnt work. Help please someone
Hi. I just bought the MX03. Is it possible to set the throttle to full power in any assist level? I just want to use the throttle to get me up to speed when accelerationg from zero without having to change to higher assist levels and then down again every time. Thank you.
The different assist levels cut out above a certain speed depending on which level you are in but should all offer some throttle assistance when starting. I generally keep mine in PAS2 or 3 to conserve the battery.
Do you know if it's possible to adjust this max speed for each individual PAS level? For me by default, PAS 1 is around 35km/h, which is way too fast. I'd like to set it up like PAS1= 15kmh PAS2= 20kmh PAS3= 25kmh And so on. Is this even possible or do I have to stick with these pre defined PAS max speeds?@@RonWalkerCairngormGuides
@@Zorandel1 On the old MX02 and 03, PAS 1 shouldn’t be as high 35 kmh the maximum on my bikes in PAS 1 is 13 kmh so something strange there! A list of the standard settings are in the video description but unfortunately you don’t have much control of the maximum speed which is set for each PAS setting.
@@RonWalkerCairngormGuides Thanks to your video, I checked all the settings. I tried many different setups and the only thing that affects PAS speeds is P08, which is max speed. For me the P08 default that my bike came with was 55. If I set it to e.g. 19, then my bike goes up to around 22kmh. But then it goes like that on all PAS settings. There's no difference between PAS 1 through 5. Only when I change it back to P08=55, does it begin to behave differently on each PAS level. Very weird...
Hi can you help me with the manual? It's a awesome bike! I set the maximum speed on 35km. When I use 'pas 3' I go around 24km. When I put it on 'pas 4' I go 35km. I would like to set it more equal. For example, when I put it on 'pas 3' I go 24km, when I put it on 'pas 4' I go around 30km and when I put it on 'pas 5' I go 35km. how do I set this up? I read the user manual, but don't know.
AFAIA the speed and max current settings are fixed within the contoller hardware and you can only make a few minor adjustments to the PAS through the M5 controller. Happy to be proved wrong though!
I talked with the manufacturer a little while ago, the speed is usually locked to 24 kmh, however if you power up the controller by pressing the menu button while holding the brake, you get an E 02 message when you start it up, keep holding the brake and change the p08 setting to 100, and your speed will be completely unlocked.
SHENGMILO and HEZZO are from the same manufacturer in China, I have faced a lot of problems with their products since April 2021. 9 out of 10 items come with either an intrinsic issue or with a developing issue. Please for your own good avoid these two brands once and for all.
Hi Guys, Please help, I've the mx02 about a year n a half now, with about 4500 km on the clock, it's well maintained and looked after, 2 weeks ago I lost power while on a cycle, the display gave me error code 010 flashing, after a bit of research I figured the controller might have given up, I ordered one n it arrived this morning, I replaced it carefully making sure all connections were solid, I switched her on & I'm still displaying "E 010" 🙈, I cleaned all the battery contacts and double checked all connections including the power lead down near the motor, still no dice, anybody have experience or experienced this issue before? And if so how would I go about resolving it? It's my daily transport n I'm kinda goosed without it, any help or information would be greatly appreciated 🙏🙏
Disconnect the headlight and headlight switch then disconnect the battery and reinstall it and see if code dissapears I had the same issue and it was the headlight/swith causing the fault when I disconnected them it went away after resetting the battery
![[#2024MAMA] BIGBANG (빅뱅) - 뱅뱅뱅 (BANG BANG BANG) + FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/EQsYfiPR9uM/mqdefault.jpg)
Dziękuję bardzo za pokazanie swoich ustawień. Tak namieszałem, że nie miałem wspomagania na korbach. Teraz wszystko działa
Great...you read us numbers. What do they mean????
th-cam.com/video/_C5iPqk6lSo/w-d-xo.htmlsi=onfewJ2OiDtHA9jS
know im a bit late but he put everything in the description, hope that helps
@@baffen3248 But doesn't really say what they are/should be/what any of it actually means. I'm confused.
Oh man you are real hero, you save my ass, Right after first ride I tried to unlock max speed and I mess up all setting and everything stops working, now it's working again and I can reach about 42km/h on Phnholun P20
Well actually my max speed is about 35km/h display is lying... I don't know how to set max speed 50km/h
Glad to be of help 😊
Same lol video helped
Love the sunlight across the screen. Here's a thought, Do Over!
muchas gracias ron es muy util este video gracias crack un saludo de jesus de españa.
P01: Jasność LCD/LCD brightness
P02: 0: KM; 1: MILE; jednostka prędkości mile/kilometry
P03: 24V, 36V, 48V, 60V; napięcie baterii (służy tylko dla wskaźnika LCD bar battery) (LCD battery level only)
P04: czas uśpienia w minutach (domyślnie 10minut) - czas wyłączenia roweru przy bezczynności; sleep time
P05: PAS number selection: 0, 3 file mode: 1,5 gear mode: ilość trybów PAS, albo 1-3 albo 1-5 albo 1-9
P06: Wheel setting inch: rozmiar koła w calach
P07: Speed gauge magnetic steel number: range: 1-100; ilość magnesów na kole do pomiaru prędkości?
P08: Speed limit setting: ograniczenie prędkości - 100 brak ograniczenia
P09: zero start, non-zero start setting： 0: zero start; 1: Non-zero start; ? konfiguracja manetki gazu?
P10: The drive mode is setting： 0: Power Drive; 1: Electric drive 2: Power Driven and Electric Driven Coexistence; konfiguracja manetki gazu?
P11: Help sensitivity setting：range: 1-24; czułość wspomagania
P12: Help start intensity setting：range: 1-5; intensywność wspomagania podczas ruszania tzw "kop"
P13: Power Magnetic Steel Disk Type Setting： 5, 8, 12 Magnetic Steel Types; parametry silnika, nie zmieniać bo przestaje wspomagać
P14: Controller limit value setting：range: 1-20A ; limit prądu kontrolera, nie zmieniać
P15: Controller undervoltage; napięcie minimalne wyłączenia, dla baterii 36V ma być =29V dla baterii 48V ma być =39V
P16: ODO zero setting： length press key 5 seconds ODO zero; resetowanie przebiegu roweru
P17 :Automatic cruise optional：0: No enabling cruising, 1: enabling cruising; tryb tempomatu (musi być zaprogramowany żeby działało)
P18: Display speed ratio adjustment： range: 50 % ~ 150 %, korekta wyświetlania prędkości, domyślnie 100%
P19: Zero PAS selection： 0: 0 file, 1: does not include 0 file; w trybach PAS można wyłączyć tryb 0 - brak wspomagania
P20 :0:2 Protocol 1:5 S Protocol 2: Standby 3: Standby ???
Ustawienia bardzo podobne w wielu modelach M6C LCD, nie ruszać P13 bo przestaje wspomagać
Are PO8 and P13 used for spped control? I am looking at buying a bike with this display.
If PO8 is used for setting the power to the motorI am not sure how you set it to the nominal or peakpower of the motor. I would simply set it to the expected km the motor shoul push?
Update Ron" i found that the Battery has movement [lateral ] this has caused the terminals to burn, [this explains the E06 /08 fault] i have clamped it tight, its solved the problem, but need new teminals, them silly 2 pin hole type are burnt,
Thank you so much my ebike m5 display settings are changed i dont know how reset but i was all copied seting your video ❤ now my ebike have normal😂
Easily done, glad to be of help
Aye ron" my display M5 needs repaced, the switch on the bars broke, tried Shengmillo theres had a short cable with round plug, mine is long full lenth square 5 wire, explained this ,but no joy,. so bought a aftermarket from chine ,see how it goes wen arrives,
Hopefully it’ll work! How has the bike been going, what mileage have you now done?
@@RonWalkerCairngormGuides Bikes been good, 480miles, apart from error 8./6. sometimes, this is connections just need split and cleaned, ,dry days are here ,so need the switch gear, etc,,[ i can link out the broken switch, to get it running,] ,but its not ideal,
My peddle assist was working great....just got the bike. Now it's now working! I've checked settings several times, any suggestions or advice? Thank you for your video
No idea
Speed limmiter shut off please ?
Check the description for controller settings
Thank you so much
Glad to help 😊
Bro seriously thank u so much@@RonWalkerCairngormGuides
@RonWalkerCairngormGuides I got a senada drifter 500 watt and holy snaps man I messed it up and it was capping at 20 followed ur steps and this thing goes 35 holy crap man seriously thank u do much I subscribed ❤❤❤❤❤❤❤❤❤
@@RonWalkerCairngormGuidesis the speeds accurate cuz I change PO 18 it was on 100 and on 150 my bike says it goes 42 mph is the speed accurate hope u get back to me if not I got a speedometer in my town I'm gonna check tonight I really hope it's accurate
I do that, but it doesn’t come up anything like that Mine comes up as 5E
My display says 43 my speed is 25, explain this?
How can u restore / reset the old setting ? The fabric setting ? Thanks u
There’s no software reset you have to manually enter the settings as each bike is different!
Last week I received my MX02s very happy with it. But after going through the settings and changing the PAS mode to 9 and back to 5 I cant reach PAS = 0. Now it by default start with PAS 1 and if I go down it stays on 1. So basically I only have PAS 1,2,3,4,5 or 1,2,3,4,5,6,7,8,9
Are P19 and P20 set to 000?
@@RonWalkerCairngormGuides 19 was set to 1. I changed it to 0. Now it’s working like original. Thanks for the tip
@@RonWalkerCairngormGuides How can I set the throttle twist grip to only support me up to 6 km/h when starting?
And how do I reduce the maximum speed to 45 kmh, like with an S Pedelec?
@@dennis9038 Maybe This setting: P08: Speed limit: Agreement No. 2 range 0-100km / H, 100 means no speed limit;
At the start your not explaining what the numbers represent in each
Setting section
It’s all in the video description!
Can you please tell me how to limit the PAS speed to 15.5Mph?
Set P08 to 25, the speed limit is in kilometres.
You can set the speed limits anywhere from 1-100.
100= no speed limit for off-road only and 25 kilometres is the EU and UK legal speed limit which is equivalent to the UK's 15.5 mph.
@@RonWalkerCairngormGuides Thank you very much. I've just done that, but for some reason, 25 = 12mph (throttle - testing indoors). I set it to 32, and it's now about 15mph. PAS 2 - 5, throttle hits 24mph.
@@emadmoussa2576 have you tried P18 the speed offset, the throttle settings are different from pedal assist, you can turn off the throttle to stay legal in the UK?
@@RonWalkerCairngormGuides I'm afraid not. Not sure what it does.
@@emadmoussa2576 If you set P10 to one you can turn off the throttle and just have pedal assist. I now have my bike set to just 3 PAS rather than 5 and use just 1 or 2 most of the time. The higher settings and speeds just gobble up the battery!
Hello, how to open the ligth ?
The light switch is on the handlebar next to the horn switch on the RHS!
A few of these settings are different to my m5, and mine only goes up to 17, not 20
What model of bike and when and where did you get it from?
I have a fortis electric bike and my settings only go to 17. Can you please help me to restore factory settings. As they have been changed and now my bike doesnt work. Help please someone
fix error 10?
I don't get that I get SP and 4 zero's on my screen
My pedal assit won't work only throttle
Hi. I just bought the MX03. Is it possible to set the throttle to full power in any assist level? I just want to use the throttle to get me up to speed when accelerationg from zero without having to change to higher assist levels and then down again every time. Thank you.
The different assist levels cut out above a certain speed depending on which level you are in but should all offer some throttle assistance when starting. I generally keep mine in PAS2 or 3 to conserve the battery.
Do you know if it's possible to adjust this max speed for each individual PAS level? For me by default, PAS 1 is around 35km/h, which is way too fast.
I'd like to set it up like
PAS1= 15kmh
PAS2= 20kmh
PAS3= 25kmh
And so on.
Is this even possible or do I have to stick with these pre defined PAS max speeds?@@RonWalkerCairngormGuides
@@Zorandel1 On the old MX02 and 03, PAS 1 shouldn’t be as high 35 kmh the maximum on my bikes in PAS 1 is 13 kmh so something strange there!
A list of the standard settings are in the video description but unfortunately you don’t have much control of the maximum speed which is set for each PAS setting.
@@RonWalkerCairngormGuides Thanks to your video, I checked all the settings. I tried many different setups and the only thing that affects PAS speeds is P08, which is max speed.
For me the P08 default that my bike came with was 55. If I set it to e.g. 19, then my bike goes up to around 22kmh. But then it goes like that on all PAS settings. There's no difference between PAS 1 through 5. Only when I change it back to P08=55, does it begin to behave differently on each PAS level. Very weird...
Do the 4 led lights on your battery still on all the time? Mine do
Only when I press the battery button which clicks on and off!
Im having a massive issue gettinh no power to my truttle any fixs
Is it set to P10: 002?
@@RonWalkerCairngormGuides what do you mean ?
Please keep in contact at work at the min
@@RonWalkerCairngormGuides there customer service is terrible
Hello . Mate
Hello, when i’m trying to get into the settings it’s asking for a code. Does somebody know the code required?
Not sure as no code required on my bike, what model is it and when did you buy it?
*For the M60, M80, M90, MX020, MX 21 Models of the eBike, the Code is: 866*
Hey buddy try 6666
Hi can you help me with the manual? It's a awesome bike!
I set the maximum speed on 35km.
When I use 'pas 3' I go around 24km.
When I put it on 'pas 4' I go 35km.
I would like to set it more equal. For example, when I put it on 'pas 3' I go 24km, when I put it on 'pas 4' I go around 30km and when I put it on 'pas 5' I go 35km.
how do I set this up? I read the user manual, but don't know.
AFAIA the speed and max current settings are fixed within the contoller hardware and you can only make a few minor adjustments to the PAS through the M5 controller. Happy to be proved wrong though!
I talked with the manufacturer a little while ago, the speed is usually locked to 24 kmh, however if you power up the controller by pressing the menu button while holding the brake, you get an E 02 message when you start it up, keep holding the brake and change the p08 setting to 100, and your speed will be completely unlocked.
@@Kristopherredfordi get nothing when i do what you say…
Wichs number to set The throttle to 6 km/h
You ever found this out?
SHENGMILO and HEZZO are from the same manufacturer in China, I have faced a lot of problems with their products since April 2021. 9 out of 10 items come with either an intrinsic issue or with a developing issue. Please for your own good avoid these two brands once and for all.
Hi Guys,
Please help, I've the mx02 about a year n a half now, with about 4500 km on the clock, it's well maintained and looked after, 2 weeks ago I lost power while on a cycle, the display gave me error code 010 flashing, after a bit of research I figured the controller might have given up, I ordered one n it arrived this morning, I replaced it carefully making sure all connections were solid, I switched her on & I'm still displaying "E 010" 🙈, I cleaned all the battery contacts and double checked all connections including the power lead down near the motor, still no dice, anybody have experience or experienced this issue before? And if so how would I go about resolving it? It's my daily transport n I'm kinda goosed without it, any help or information would be greatly appreciated 🙏🙏
@Ron Walker
Disconnect the headlight and headlight switch then disconnect the battery and reinstall it and see if code dissapears I had the same issue and it was the headlight/swith causing the fault when I disconnected them it went away after resetting the battery