Hello I have a ouxi h9 and I put this one on it but it doesn’t accelerate and it also goes out from itself. Do you know what to do? also when I put it on the fatbike the cables were different. The one on my fatbike is xmdy and the one that I ordered is xsd. Please help me
@anoublezbie Most LCD displays & controllers. Are programmed together if you try to mismatch them it ma cause not to run correctly. Even burn up the LCD or controller. Not all are compatible with each other.
@@anoublezbie Not a lot of information out on that display at this time. However, arcode 08 usually indicates either a faulty throttle or a hall sensor issue in most cases. I suggest unplugging the LCD display as well as the throttle. Checking the pins if everything looks good. Reconnect these wires in most cases, if they're not quick. Disconnect and these are high go connectors. They will have Arrows to lineup and snap back in place. In one case I even seen This code comes up because the tire size was programmed incorrectly.
Hello I really need to know how to remove the speed limiter on E-Mountainbike MONTIS EM 1726 by FISCHER with bafang display. Can u tell me how or if its possible? The e bike is really fast but its limited at 25-27kmh
Without knowing what display you have, it's hard to say. Never heard of it, so I'm guessing that must be an Amazon bike. On the back of the display, there should be a number embossed into the plastic or a sticker on it that will give you a number like KT - 153.
@@theebikeguy3852 Thanks was able to figure it out it was 6666 👹 it was a M5 display & controller off a fake super 73. Just have to enter it every time I want to access the settings
Hey i have the same display as you, but mine won't give any power and the speedometer isn't accurate do you maybe know what to do? My bike is a Ouxi V8
First try disconnecting both of you Breaking inhbiters. If you do not have power and if you had went into the settings and messed with anything that would cause it not to run, it could also throw the battery to read inaccurate or if you mess with the magnet numbers you could burn up to display or the controller. If you haven't done any other hat and the speed ometer is just slightly off the only thing you would have to do is adjust the wheel size to change the speed As far as it. Not working usually there is an Error code..... Do you have pedal assist but not throttle? If so, most likely your throttle is defective.
@@MrAgben You would have to get into the display. And bypass the power switch solder it on the board to where it comes on immediately. Not a easy task.
This was sooo incredibly helpful, thank you so much. Although I'm still looking for what the person I bought it from has shown me; apparently he was able to set the maximum speed in each PAS "level" but I cannot remember for the life of me how he did that. Is that actually feasible?
@@xshu_. If you are referring to pedal assist, I believe the M5 will drop down to 0 on the LCD display. One. Through 5 is pedal assist if you put it on 0. There should be no pedal. Assist only showing your speed and the knowledge that you travel.
I dont get pedal assist at any level, even level 5.. i think i need to disable the manual "mode" next to the PAS 1-5 section but i can't find anything online. I hoped you would know a solution
@BenBlaauw-dp8ps If you have throttle only and no pedal assist. Then Like Likely you have a cut wire on the pedal assist Are possibly the petal assist Hall scensor is bad
@@ThomasIwang-z5k Try to. Disconnect the LCD display from the controller for 5 minutes. I'm not sure if the M5 has 3 or 4 which equals a security code I forget.
You might try to charge the setting on P10 This will switch peddle assest and throttle, Also, you may try disconnecting the LCD display from the controller.Plugging it back in also disconnect the motor from the controller and plug it back in. If it does not work it may have a partly faulty controller or motor if it does not work, Do you have any air codes on the screen? I can explain to you how to run a test on the motor to find out if it is the problem if that does not work. For some weird reason, I have seen some of these say manual on the screen. Others do not have anything there and they work fine so it's kind of weird honestly I really don't know what that is. But in the past it is not affected. Any electric bike that I worked on with this display.
@@lordsmobilekrim3763 Try to disconnect each hygo connector. Make sure no pins are bent lineup the Arrows reconnect. Also, with the throttle disconnected, turn on the bike and see if it shows an error code. If there are no error codesit will be likely the throttle.
Go to 16P. Press The minus button for approximately 5 seconds.I believe this screen We'll flash 000. Then press plus and money said the same time To get out of the settings. Power it off and back on it should reset
I've done all that I can get in but when I go to next setting the numbers won't change up or down? I have to replace it I think it maybe faulty nothing works the other bike has no problem
Most likley a communication receive from controller to the LCD display...if this is a Hygo Conecter plug, unplug the LCD Display, make sure no pins are bent or any Corrosion is present. If everything looks good line, the 2 arrows up on each side of the high go connector press firmly to reconnected. See, if that clears the code. If not, you may have to buy a new l. C. D display.
And as far as helping your battery last longer, no the battery has it's own cut off settings in it's BMS which over rides anything the bike controller tries to do.
How do you count the polls in the motor? DiroDi Rover Plus Gen 5 Video is very helpful
th-cam.com/video/peXdUegyfTA/w-d-xo.htmlsi=qxKxS657B_q2DrrL
Hello
I have a ouxi h9 and I put this one on it but it doesn’t accelerate and it also goes out from itself. Do you know what to do? also when I put it on the fatbike the cables were different. The one on my fatbike is xmdy and the one that I ordered is xsd. Please help me
@anoublezbie Most LCD displays & controllers. Are programmed together if you try to mismatch them it ma cause not to run correctly. Even burn up the LCD or controller. Not all are compatible with each other.
@@theebikeguy3852 hi. What does error e008 mean on a h6c display?
And what happens if I ride with it
@@anoublezbie Not a lot of information out on that display at this time. However, arcode 08 usually indicates either a faulty throttle or a hall sensor issue in most cases. I suggest unplugging the LCD display as well as the throttle. Checking the pins if everything looks good. Reconnect these wires in most cases, if they're not quick. Disconnect and these are high go connectors. They will have Arrows to lineup and snap back in place. In one case I even seen This code comes up because the tire size was programmed incorrectly.
@@theebikeguy3852 oke
Hello I really need to know how to remove the speed limiter on E-Mountainbike MONTIS EM 1726 by FISCHER with bafang display. Can u tell me how or if its possible? The e bike is really fast but its limited at 25-27kmh
Without knowing what display you have, it's hard to say. Never heard of it, so I'm guessing that must be an Amazon bike. On the back of the display, there should be a number embossed into the plastic or a sticker on it that will give you a number like KT - 153.
@@theebikeguy3852 The display is Bafang DP C10
I have a new M5 display that is asking for a 4 digit code before I can get into the display settings. Are you aware of anything like that?
@@mattbuyak2128 try 9999 or 0000
@@theebikeguy3852 Thanks was able to figure it out it was 6666 👹 it was a M5 display & controller off a fake super 73. Just have to enter it every time I want to access the settings
@@mattbuyak2128 Oh, lovely. The mark of the Beast. How nice.. lol
@@mattbuyak2128hey
Hey i have the same display as you, but mine won't give any power and the speedometer isn't accurate do you maybe know what to do? My bike is a Ouxi V8
First try disconnecting both of you Breaking inhbiters. If you do not have power and if you had went into the settings and messed with anything that would cause it not to run, it could also throw the battery to read inaccurate or if you mess with the magnet numbers you could burn up to display or the controller. If you haven't done any other hat and the speed ometer is just slightly off the only thing you would have to do is adjust the wheel size to change the speed As far as it.
Not working usually there is an Error code..... Do you have pedal assist but not throttle? If so, most likely your throttle is defective.
Thanks I'm having all these problems with my kit thanks guys
Can u set the display to auto-on when turning the battery switch on?
@@MrAgben You would have to get into the display. And bypass the power switch solder it on the board to where it comes on immediately. Not a easy task.
This was sooo incredibly helpful, thank you so much. Although I'm still looking for what the person I bought it from has shown me; apparently he was able to set the maximum speed in each PAS "level" but I cannot remember for the life of me how he did that. Is that actually feasible?
@@beatrixujj1447
www.shengmilo-bikes.com/blogs/news/shengmilo-m5-display-settings
How do you get out of Manual?
What do you mean??? Are you talking about the bike taking off with the throttle, or peddling before it will work?
Hey how do you disable or enable the manual mode on the m5 screen ?
@@xshu_. If you are referring to pedal assist, I believe the M5 will drop down to 0 on the LCD display. One.
Through 5 is pedal assist if you put it on 0. There should be no pedal. Assist only showing your speed and the knowledge that you travel.
I dont get pedal assist at any level, even level 5.. i think i need to disable the manual "mode" next to the PAS 1-5 section but i can't find anything online. I hoped you would know a solution
@@xshu_. change settings in P10, If that does not work, you likely have a bad pedal. Assist sensor.
Did u fix this yet having the same problem even when P010 is on 2
@BenBlaauw-dp8ps If you have throttle only and no pedal assist. Then Like Likely you have a cut wire on the pedal assist Are possibly the petal assist Hall scensor is bad
hi i got a m6 display and i have evrything the same but cannot change anything
This is M5 display. The M6 display is a color display and has different settings If I recall.
Mine keeps saying errors on p02 what is this meaning plus I have no throttle power at all
hi - my M5 display will not show the actual speed - only "000" - any idea?
@@ThomasIwang-z5k Try to.
Disconnect the LCD display from the controller for 5 minutes. I'm not sure if the M5 has 3 or 4 which equals a security code I forget.
Can i make it so that when i press something my speedlimit goed back to 25 km/h?
If you're referring to the top speed. Go to PZ rotate. If it is set at 100%. Try 80% and see how that goes.
His display says “manual” . Does that mean it is pedal only? Mine says this and it is stuck there. Throttle won’t work, or pedal assist. Someone help
You might try to charge the setting on P10 This will switch peddle assest and throttle, Also, you may try disconnecting the LCD display from the controller.Plugging it back in also disconnect the motor from the controller and plug it back in. If it does not work it may have a partly faulty controller or motor if it does not work, Do you have any air codes on the screen? I can explain to you how to run a test on the motor to find out if it is the problem if that does not work. For some weird reason, I have seen some of these say manual on the screen. Others do not have anything there and they work fine so it's kind of weird honestly I really don't know what that is. But in the past it is not affected. Any electric bike that I worked on with this display.
Did you get an akez bike by chance throttle is disconnected on shipment @km0577
@asahogreve1331 I'm a 12 yr. Ebike Tec. I don't have any ebikes just a Wolf king GT PRO AND ordered a Nami
bro i have h9 display m5 but when i click - doesnt work there is no code
@@lordsmobilekrim3763 Try to disconnect each hygo connector. Make sure no pins are bent lineup the Arrows reconnect. Also, with the throttle disconnected, turn on the bike and see if it shows an error code. If there are no error codesit will be likely the throttle.
my only goes to 03p on my dyu any idea why?
Different
Companies have.
the displays programmed in a different manner.
@@theebikeguy3852 ya DYu sucks
@jamesishere6630 lol, ya get what you pay for, but for the price it's decent.
How to factory reset???
Go to 16P. Press The minus button for approximately 5 seconds.I believe this screen We'll flash 000. Then press plus and money said the same time To get out of the settings. Power it off and back on it should reset
Qual a senha para desbloquear e poder aumentar velocidade para 100?
My settings won't change any ideas why
Never seen one that could not if you hold the up and down button at the same time for about 5 sec. Should go into p settings.
I've done all that I can get in but when I go to next setting the numbers won't change up or down? I have to replace it I think it maybe faulty nothing works the other bike has no problem
Thanks for the video I got an m5 LCD screen and it is reading an error code. E-010 I've read a few different things but aren't sure. Thanks
Most likley a communication receive from controller to the LCD display...if this is a Hygo Conecter plug, unplug the LCD Display, make sure no pins are bent or any Corrosion is present. If everything looks good line, the 2 arrows up on each side of the high go connector press firmly to reconnected. See, if that clears the code. If not, you may have to buy a new l. C. D display.
Thanks for letting us know looks like I better get a new lcd mine is brand new with the motor kit 😭 😭 😭 😭 @@theebikeguy3852
Mine is shutting off in 10 seconds
@@jeembaymusic5271 Are you referring to when you're writing it or if it's just setting in one spot?
Hello
My amps goes up to 31 amps.
Was factory default @22.
And as far as helping your battery last longer, no the battery has it's own cut off settings in it's BMS which over rides anything the bike controller tries to do.
@@verily1221 factory default 12