There are a few ways to disable the seat belt alarm on a BMW E60. Use a seat belt emulator. A seat belt emulator is a device that plugs into the seat belt buckle and sends a signal to the car's computer that the seat belt is buckled, even if it's not. This is the most common way to disable the seat belt alarm. You can find seat belt emulators online or at some auto parts stores. Disconnect the seat belt sensor. The seat belt sensor is located under the seat. You can disconnect the sensor by removing the screws that hold it in place and then disconnecting the electrical connector. This is a more permanent solution, but it's also more difficult to do. Use a diagnostic tool. If you have a diagnostic tool, you can use it to disable the seat belt alarm in the car's computer. This is the most technical solution, but it's also the most reliable. Here are the steps on how to disable the seat belt alarm using a diagnostic tool: Connect the diagnostic tool to the car's OBD-II port. Launch the diagnostic tool software. Find the airbag module in the vehicle list. Enter the security code for the airbag module. Change the setting for the seat belt alarm to "disabled". Save the changes and exit the diagnostic tool software. Once you have disabled the seat belt alarm, the chime will no longer sound when you start the car or if the seat belt is not buckled. However, it's important to note that disabling the seat belt alarm can be dangerous. If you are in a collision, the airbags may not deploy properly if you are not wearing your seat belt. Therefore, it's important to weigh the risks and benefits before disabling the seat belt alarm. I hope this informaton is helpful for you.Thank You.
es, the LAUNCH CR629 OBD2 scanner should be able to read air flow rate in grams per second (g/s) on live data. Here's why: The CR629 is advertised to support "Full OBD2 Functions" which includes reading live data streams www.launchcrp.com/products/launch-cr629-car-obd2-scanner. Live data streams typically include Mass Air Flow (MAF) sensor readings which measure air intake in grams per second obdsoftware.my.site.com/s/article/How-to-read-OBDII-live-data-A-mechanic-guide. While the CR629 manual might not explicitly state "grams per second" as a unit, the live data reading for MAF sensor should display a value that you can interpret as air flow rate. Here's a tip: Once you connect the scanner and turn on the car, navigate to the live data section on the CR629. Look for a parameter labeled "MAF" or "Mass Air Flow". The value next to it should be the air flow rate, possibly in grams per second or a similar unit. If you can't find it or the unit is unclear, consult the CR629 user manual or search online for specific information about the data stream readings for your car model.
Click the link below for a limited-time discount!⬇
✅👉Best OBD2 Scanner: ✅✅✅ (Amazon)✅✅✅
✅Buy LAUNCH OBD2 Scanner:(Amazon) amzn.to/4d5jA77
✅Automotive Tools & Equipment:(AMAZON ) amzn.to/3W5PjhD
✅Best Code Readers & Scan Tools:(AMAZON )amzn.to/4cYLmSG
✅ ANCEL AD310 OBD II Scanner:(AMAZON ) amzn.to/3tIiBIV
✅BlueDriver Bluetooth Pro OBDII Scan Tool :(AMAZON ) amzn.to/3NXvYfc
✅MOTOPOWER MP69033 Car OBD2 Scanner :(AMAZON ) amzn.to/3RUdq
can you with this delite seat belt alarm on bmw e 60?
There are a few ways to disable the seat belt alarm on a BMW E60.
Use a seat belt emulator. A seat belt emulator is a device that plugs into the seat belt buckle and sends a signal to the car's computer that the seat belt is buckled, even if it's not. This is the most common way to disable the seat belt alarm. You can find seat belt emulators online or at some auto parts stores.
Disconnect the seat belt sensor. The seat belt sensor is located under the seat. You can disconnect the sensor by removing the screws that hold it in place and then disconnecting the electrical connector. This is a more permanent solution, but it's also more difficult to do.
Use a diagnostic tool. If you have a diagnostic tool, you can use it to disable the seat belt alarm in the car's computer. This is the most technical solution, but it's also the most reliable.
Here are the steps on how to disable the seat belt alarm using a diagnostic tool:
Connect the diagnostic tool to the car's OBD-II port.
Launch the diagnostic tool software.
Find the airbag module in the vehicle list.
Enter the security code for the airbag module.
Change the setting for the seat belt alarm to "disabled".
Save the changes and exit the diagnostic tool software.
Once you have disabled the seat belt alarm, the chime will no longer sound when you start the car or if the seat belt is not buckled. However, it's important to note that disabling the seat belt alarm can be dangerous. If you are in a collision, the airbags may not deploy properly if you are not wearing your seat belt. Therefore, it's important to weigh the risks and benefits before disabling the seat belt alarm.
I hope this informaton is helpful for you.Thank You.
Hi on live data, can it read in grams per second, G/S? On air flow rate? Any reply appreciated cheers from Australia ❤subbed and liked 👍
es, the LAUNCH CR629 OBD2 scanner should be able to read air flow rate in grams per second (g/s) on live data.
Here's why:
The CR629 is advertised to support "Full OBD2 Functions" which includes reading live data streams www.launchcrp.com/products/launch-cr629-car-obd2-scanner.
Live data streams typically include Mass Air Flow (MAF) sensor readings which measure air intake in grams per second obdsoftware.my.site.com/s/article/How-to-read-OBDII-live-data-A-mechanic-guide.
While the CR629 manual might not explicitly state "grams per second" as a unit, the live data reading for MAF sensor should display a value that you can interpret as air flow rate.
Here's a tip:
Once you connect the scanner and turn on the car, navigate to the live data section on the CR629.
Look for a parameter labeled "MAF" or "Mass Air Flow". The value next to it should be the air flow rate, possibly in grams per second or a similar unit.
If you can't find it or the unit is unclear, consult the CR629 user manual or search online for specific information about the data stream readings for your car model.
@@weeklytools dude! Thanks heaps for the quick reply! I had to subscribe and like 👍. Thanks again! 🙂
you are most welcome Sir.