I have inherited a Precor 931 treadmill . It was partially under water due to a flood . Now works fine but has an unbearable rumple noise seeming from front and back . maybe the roller ( belt rollers ) bearings have been rust-pitted . Please try to offer some advice . I appreciate all your helpful videos . Johnnie C . Nova Scotia
My brand new 445 has a rattling sound in the rear roller when going less than 2mph. It sounds like a loose piece of metal that rolls when the roller rotates. I can hear it if I manually turn the belt very slowly with the machine off too.
I have a very strange noise coming from my treadmill. It’s a deep drum base sound that repeats twice per 1 belt cycle. It seems to be coming from the rear roller region. It gets louder and with a higher pitch the faster the belt moves. Any suggestions on what it might be and how to fix it?
That is the overlapping fold where the belt is seamed together and is thicker at that point... so every time it rolls over the roller it makes that thud and once at the front and once at the back... Thud... Thud... Thud.. Thud..
Mine is clicking :( A ball got stuck under it and it stopped while it was still on. Any advice on how I can fix it? Belt is moving fine and the lights on then screen are all on and normal, just terrible clicking sound. Thanks!! :D
Hi, I'm having the crackling sound. Where can I buy the treadmill lubricant? Also if I am hearing the crackling sound is that dangerous? Or is it still OK to walk on?
Hello, my treadmill is making this constant deep sound that gets louder the faster my treadmill gets, as if the running deck is grinding against the surface. Is there a way to stop the noise?
@@scottsnyder2229that's what I'm wondering . He wasn't very descriptive on where to apply stuff . I'm guessing you lift the belt and just spray a little underneath though
@@coloradocardio Thanks so much for your reply. With a new deck/belt/ and replaced front roller, it seems much better BUT......it grumbles/vibrates at startup speeds of 1-3, but goes away "magically" at speeds 4+. Belt and rollers are aligned. Thoughts? I noticed I can twist the DRIVE belt 90 Degrees from the center point between pullies. Perhaps that's an issue? Not sure if moving the front roller back toward rear of treadmill will help tighten the motor belt or not.
I'm having the exact issue as the first part in the video where there's a clicking sound when it's running between 1-2mph. I put a dry rag under there and ran it a little bit. The rag had some dirt on it but still have the same clicking sound. Precor 9.27
It's hard to tell what sound you are getting and where it is coming from, it could be coming from your rollers or there is just more dirt underneath the belt. But without seeing/hearing your treadmill run I'd just be guessing.
@@coloradocardio th-cam.com/users/shortsfC8FRVyx5vk?feature=share I’m the same person, couldn’t log in from my phone to that account. The treadmill is obviously fully turned off in the video but does the same when it’s on so I’m guessing it can’t be the motor?
Your running deck might have come loose and needs reattached. Or the front roller has come out of it slot and not sitting right. Take off the front cover and run without it on see if you can see where the noise is coming from.
Bar of soap on the drive belt worked perfect. Thank you!
Excellent!
I have inherited a Precor 931 treadmill . It was partially under water due to a flood . Now works fine but has an unbearable rumple noise seeming from front and back . maybe the roller ( belt rollers ) bearings have been rust-pitted . Please try to offer some advice . I appreciate all your helpful videos . Johnnie C . Nova Scotia
My brand new 445 has a rattling sound in the rear roller when going less than 2mph. It sounds like a loose piece of metal that rolls when the roller rotates. I can hear it if I manually turn the belt very slowly with the machine off too.
I have a very strange noise coming from my treadmill. It’s a deep drum base sound that repeats twice per 1 belt cycle. It seems to be coming from the rear roller region. It gets louder and with a higher pitch the faster the belt moves.
Any suggestions on what it might be and how to fix it?
That is the overlapping fold where the belt is seamed together and is thicker at that point... so every time it rolls over the roller it makes that thud and once at the front and once at the back... Thud... Thud... Thud.. Thud..
Mine is clicking :( A ball got stuck under it and it stopped while it was still on. Any advice on how I can fix it? Belt is moving fine and the lights on then screen are all on and normal, just terrible clicking sound. Thanks!! :D
Hi, I'm having the crackling sound. Where can I buy the treadmill lubricant? Also if I am hearing the crackling sound is that dangerous? Or is it still OK to walk on?
You can get treadmill silicone on Amazon. It is still ok to walk on just get the silicon sooner than later.
@@coloradocardio ok thank you so much
Hey my tredmill is making a clicking noise from the motherboard and has a bit of a smell , tredmill is erratic with speed ,what could be the issue ?
Replace motherboard (IFT Box) eBay has them used for around $100
Hello, my treadmill is making this constant deep sound that gets louder the faster my treadmill gets, as if the running deck is grinding against the surface. Is there a way to stop the noise?
You can put liquid silicone underneath the belt to reduce friction
So you put the lube right on the belt, I think you say that in the vid. OR btwn the underside of the belt and deck?
@@coloradocardio
@@scottsnyder2229that's what I'm wondering . He wasn't very descriptive on where to apply stuff . I'm guessing you lift the belt and just spray a little underneath though
Most (or all) or Precor decks are lubricated for life. The Precor decks are double sided and can be flipped. Other brands handle lubricant well.
Ture, however after they have been replaced with aftermarket parts (Belts and Deck) these will need to be siliconed or lubricated.
What's wrong if my c956i Precor makes a vibrating grinding sound at first run up, but after cycling the power switch, acts as normal?
You running belt might be dry and will need treadmill silicon applied to the under side of the belt/deck so it runs smoothly.
@@coloradocardio Thanks so much for your reply. With a new deck/belt/ and replaced front roller, it seems much better BUT......it grumbles/vibrates at startup speeds of 1-3, but goes away "magically" at speeds 4+. Belt and rollers are aligned. Thoughts? I noticed I can twist the DRIVE belt 90 Degrees from the center point between pullies. Perhaps that's an issue? Not sure if moving the front roller back toward rear of treadmill will help tighten the motor belt or not.
I'm having the exact issue as the first part in the video where there's a clicking sound when it's running between 1-2mph. I put a dry rag under there and ran it a little bit. The rag had some dirt on it but still have the same clicking sound. Precor 9.27
It's hard to tell what sound you are getting and where it is coming from, it could be coming from your rollers or there is just more dirt underneath the belt. But without seeing/hearing your treadmill run I'd just be guessing.
@@coloradocardio
th-cam.com/users/shortsfC8FRVyx5vk?feature=share
I’m the same person, couldn’t log in from my phone to that account.
The treadmill is obviously fully turned off in the video but does the same when it’s on so I’m guessing it can’t be the motor?
Roller bearings make a crackling sound at low speed also.
My tredmill is making a clicking noise front left side.
Check your drive belt that is connected to the motor, put a little soap on it and see if that makes the noise go away. If not let me know
Can olive oil lubricate it lol
WOW never thought or heard of that but possibly would work I don't see a problem with it. et me know if you use it and how it works for you.
Mine makes a noise when i step its like i was banging on a door
Your running deck might have come loose and needs reattached. Or the front roller has come out of it slot and not sitting right. Take off the front cover and run without it on see if you can see where the noise is coming from.
What's up with the 💅🏾?
I love them!