This is the best video on this topic I’ve seen. I watched several. . . . Followed all of of instructions and suggestions, and my photo turned great. Beyond my expectations.
I've tried so many different ways to try to transfer pictures onto wood with not to luck. Until i watched your video, by far yours was the best I've ever tried, Thank you for the tips, you saved my alot of headaches , good job amigo
I enjoyed watching because the video started off letting you know where various point's of interest were. Furthermore, you might consider using a Monochrome, or Black and White photo as well as consider the direction of the wood grain. I learned a lot the way you presented your information. It was informative, concise and left room for opinion and growth!
This is the most thorough video I've seen on this so far, and the timeline at the beginning was very thoughtful! The editing is pleasant too! I'm surprised it has so few views really Thanks for taking time to make this! : )
I wish I could share my failures. I have tried and tried to transfer with the polly. I have done a thin coat, a thick coat, and everything in between. I have waited any were from 1 hour to 28 hours. Every time 60 - 90% of the photo runs off with the paper. Ppl please, any suggestions would be SO helpful!!
i've noticed when doing it this way , a fair amount of the image rubs off with the paper. Is there any step i'm missing or rushing that you've found could cause this?
I used the minwax matte polycrylic to adhere my picture to cedar plank. I have tried to take all the paper off in five or six steps but when it dries it's completely cloudy. Did I put too much polycrylic on? It doesn't look like it's cloudy from the paper but rather cloudy from something else
Thank you for this video! I read so many posts and watched too many videos only to find out that I need a lazer printer. Your the only person I've found that mentions this. Thank you!
Hey Mark, thanks for the comment. I personally haven't tried having a print be outside in the elements, but I don't think the polycrylic is recommended for outdoor use. Maybe you could put a better finish over the final project that is more suited to be outdoors, possibly a polyurethane or varnish!
Have you tried doing the print on a wax paper or the glossy side of a sheet of labels (without labels of course). I have seen others doing it but not using polycrylic.
I've tried many times but I can never get the paper off without ripping the image and ruining the product is there something I am doing wrong? Can you go into more detail about how you remove the paper after everything has dried?
Hey Stephanie. I know it’s really tough, it seems like in the end it’s impossible to not take some of the photo off. I think the biggest thing for me was to not be too rough when rubbing off the paper. Also make sure that the paper is wet enough when rubbing, if it’s too dry I think that could take some of the ink off easier. Hopefully those might be helpful, I wish I had the process down a little more myself!
Can you please tell me why my paper ripped when I was rubbing the picture off, this is very frustrating, I have tried this so many w!!!! I used a laser printer and also the same polycrylic !! Please help me understand what I am doing wrong!!!!😢
This was a very good video. I inkjet printed some pictures and was just curious if the polycrylic would go through the paper photo and ruin it, but I guess I'll just have to see if it does, lol. Thank you for sharing.
Hey thanks for watching! That’s a pretty interesting thought. I’m not 100% sure what would happen, but my guess would be that it probably will go through the paper and mess up the ink. Let me know what happens if you do try it! 😃
Thank you for the hint about taking the paper off in several layers. The other video I watched didn't mention that and I went in too hard and took off the ink :(
Thanks so much Charlotte! I don’t think I’d know for sure if it would work, but my guess would be that it wouldn’t. I don’t think the ink could make it through the oil, but maybe if it’s light enough it just may work. 👍🏼
@@LucasMoore thank you for this tutorial. How would I go about this if I am transferring a laser image to acrylic painted wood slice? Could I seal it with a coat of the polycrylic let it dry- then do another coat for transfer?
I have tried this half a dozen times with pine and everytime chunks of the picture rub off with the paper. I let it dry over an hour even. What am I doing wrong?
So you WET it before taking off the picture . All the videos I’ve been watching just take it right off w no issues yet I cannot figure out how they do it ! I am frustrated . Maybe this is the KEY , wetting it ?! Let’s see if it works for me or else I just can’t keep trying . I tried mod podge, poly and a medium gel all unsuccessfully today . Looks amazing !!
Woah that would be so cool, I would love to see how that turns out! That's an interesting point, tbh I don't know much about that I will have to learn about the cells thanks for the tip 👍
Question... want to transfer a photo onto a black painted (store bought) frame. Will this method work for something painted and already finished? If you have an email I can send example, but basically I am going to take a picture and extend the picture into the frame. Maybe you can visualize? Picture, surrounded by a mat, but the edges of the picture extend beyond the mat onto the frame. Preferably a painted black frame. Think night shot, a mat to isolate the picture, then a frame to extend the edges of the picture. Black frame for darkness of night but color image added to it to extend the picture... I hope that makes sense?.?.
Thank you for this video! When I tried this the paper seemed to bubble a little after I smoothed it down and it was too wet to smooth out again without tearing it. Any suggestions on how to fix that or is it normal?
Thank you so much - one of the best instructables I've seen! I am tempted to try it. Completely off topic, but noticed your sofa...is it a Hans Olsen (Danish mid-century)? I have two Hans Olsen lounge chairs that look just the same - the rosewood arms (and typically chrome/nylon strapping at the back) are quite distinctive features.
Hey thanks for watching and commenting. I don’t think that the sofa is a Hans Olsen. We got it off Wayfair so I would say it’s definitely nothing too fancy haha.
This was great. I especially appreciate the fact that you took the extra time for the very thoughtful tips at the end. Thanks!
Thanks so much for that Dan, I appreciate you taking the time to watch and comment!
This is the best video on this topic I’ve seen. I watched several. . . .
Followed all of of instructions and suggestions, and my photo turned great. Beyond my expectations.
I've tried so many different ways to try to transfer pictures onto wood with not to luck. Until i watched your video, by far yours was the best I've ever tried, Thank you for the tips, you saved my alot of headaches , good job amigo
I enjoyed watching because the video started off letting you know where various point's of interest were. Furthermore, you might consider using a Monochrome, or Black and White photo as well as consider the direction of the wood grain. I learned a lot the way you presented your information. It was informative, concise and left room for opinion and growth!
Lucas, Thank you for the excellent lesson. Looking forward to trying it. I’ve seen many ways
to do it but I will try your’s.
amazing video Lucas. Best how to I've seen
Wow, thanks so much. I appreciate you checking it out!
Best ever explanation ever👍👍👍
Thank you so much, glad it was helpful!
Outstanding video. Very nicely done and lots of information. Thank you!!
Thank you so much, you have by far been the best to advise on how to do this x
Loved how simple and clear this video was!!!! Great work
Thank you for the advice, I tried and failed at this so many times I will have to try it the way you are telling us!! Thanks again!!!
Your the goat for throwing in the table of contents at the beginning
Andrew Logar haha appreciate it! I thought about it last minute but figured it could be really helpful
Great tips at the end. Awesome video. I've watched a lot of tutorials
Love this Lucas. Thank you for sharing.
Awesome! Thanks so much for watching and commenting!
FANTASTIC! 👍🏾
Thank you so much! :)
Thank you sir, I know what I’m gonna try this weekend!!
This is the most thorough video I've seen on this so far, and the timeline at the beginning was very thoughtful! The editing is pleasant too! I'm surprised it has so few views really
Thanks for taking time to make this! : )
Wow, thank you so much that's really encouraging to hear I'm so glad you enjoyed it! I appreciate you taking the time say that :D
@@LucasMoore Of course! I'm glad it is!
@Raymond Landen 100% Scam, you really have to love money more than anything, sheesh
IN HINDI,,hindi me video please......
Beautifully shot video
Thanks souch for sharing this. I found it very helpful and informative.
I wish I could share my failures. I have tried and tried to transfer with the polly. I have done a thin coat, a thick coat, and everything in between. I have waited any were from 1 hour to 28 hours. Every time 60 - 90% of the photo runs off with the paper. Ppl please, any suggestions would be SO helpful!!
I like it I will try it thankyou for teaching
Brilliant, well presented and informative.
Thanks, Im glad you enjoyed it!
Explained in simple way . Thanks
This was super detailed, and thus very helpful. Thanks!!
Thank you so much for taking the time to watch and comment!
THANK YOU ! I’m super excited to try this.
Thx a lot. I wonder if a roller works better than a putty knife.
I tried various papers. Let’s see if I put enough polycrylic on
9:07 was my favorite expression of using the flow of the wood grain for the right picture!
Hey, thanks for the idea - my daughter and I are going to give this a go today! Thank you for sharing!😊
Great job! I love it!!!
Thank you!! :D
Do you know if this would fade away with rain? Wanna use this technique for some outdoor exhibition
i've noticed when doing it this way , a fair amount of the image rubs off with the paper. Is there any step i'm missing or rushing that you've found could cause this?
Ciao La foto è con carta semplice o con la carta speciale per le photo?grazie
I have the poly spray. Can I use that?
I used the minwax matte polycrylic to adhere my picture to cedar plank. I have tried to take all the paper off in five or six steps but when it dries it's completely cloudy. Did I put too much polycrylic on? It doesn't look like it's cloudy from the paper but rather cloudy from something else
Thank you for this video! I read so many posts and watched too many videos only to find out that I need a lazer printer. Your the only person I've found that mentions this. Thank you!
How does this procedure hold up outside in the elements?
Hey Mark, thanks for the comment. I personally haven't tried having a print be outside in the elements, but I don't think the polycrylic is recommended for outdoor use. Maybe you could put a better finish over the final project that is more suited to be outdoors, possibly a polyurethane or varnish!
Have you tried doing the print on a wax paper or the glossy side of a sheet of labels (without labels of course). I have seen others doing it but not using polycrylic.
I've tried many times but I can never get the paper off without ripping the image and ruining the product is there something I am doing wrong? Can you go into more detail about how you remove the paper after everything has dried?
Hey Stephanie. I know it’s really tough, it seems like in the end it’s impossible to not take some of the photo off. I think the biggest thing for me was to not be too rough when rubbing off the paper. Also make sure that the paper is wet enough when rubbing, if it’s too dry I think that could take some of the ink off easier. Hopefully those might be helpful, I wish I had the process down a little more myself!
A giant Thank you for showing this procedure. It is greatly appreciated!!!
Can you please tell me why my paper ripped when I was rubbing the picture off, this is very frustrating, I have tried this so many w!!!! I used a laser printer and also the same polycrylic !! Please help me understand what I am doing wrong!!!!😢
This was a very good video. I inkjet printed some pictures and was just curious if the polycrylic would go through the paper photo and ruin it, but I guess I'll just have to see if it does, lol. Thank you for sharing.
Hey thanks for watching! That’s a pretty interesting thought. I’m not 100% sure what would happen, but my guess would be that it probably will go through the paper and mess up the ink. Let me know what happens if you do try it! 😃
can you do this on a panted surface
what is the "different technique" using an inkjet printer?
Top video mate
Very cool...thank u!
Much love for the timelist
Thank you for the hint about taking the paper off in several layers. The other video I watched didn't mention that and I went in too hard and took off the ink :(
By far, this is one of the most insightful videos! Thank you for being thorough!
Also where did you frame them
I used acrylic gell medium and mod one yellow box after transferring my picture is turning white pls reply what to do where I'm going wrong
So good bro thank ya
You are welcome man, appreciate you taking the time to check it out!
I,ll have to try this. Thanks.
Can you get a laser print from an S D camera card ?
What is the paper material that you used?
How long did u wait for it to dry each time you had re wet it
Thank you! Great info, I’m excited to try this soon!
You are very welcome, thanks for checking out the video and taking the time to comment!
Keep up the great work excellent video-Daniel
Love it keep it going ..
they make a spray can poly crylic ... will it work?
does an actual printed photo work? like the kind you drop off at the store for developing....
Great not boring
Very good explanation, thanks.
where do you get you 8 X 11 piece of pine?
Looks great!
Thank you!! 😃
Amazing! Very very cool. Do you know if this would work on already lightly oiled bamboo?
Thanks so much Charlotte! I don’t think I’d know for sure if it would work, but my guess would be that it wouldn’t. I don’t think the ink could make it through the oil, but maybe if it’s light enough it just may work. 👍🏼
Thank you very much! I looked for this a lot of time!
Thank you so much for taking the time to watch and comment!
@@LucasMoore thank you for this tutorial. How would I go about this if I am transferring a laser image to acrylic painted wood slice? Could I seal it with a coat of the polycrylic let it dry- then do another coat for transfer?
I have tried this half a dozen times with pine and everytime chunks of the picture rub off with the paper. I let it dry over an hour even. What am I doing wrong?
amazing, thank you, you're awesome)
I think a pint is now 25d on amazon
i tried this ,the picture came out on the canvas but when i sealed with the polycrylic it caused the picture to bearly show ,why is that?
Is the polyurethane oil base
Will this work with regular pictures or just copy paper
Awesome video thank you 😁👍
You didn’t show how you wet the photograph. Did you use a sponge or just dip your fingers in water?
The video is best&helpfully.
1 question what is name of paint chemical
Minwax polycrylic water based sealer. Gloss is shiny, satin is less shiny.
what paper setting you use for the laser to print on the label paper
Does this work on black and white photos or does it need to be color? Just tried on and nothing transfered lol
Thank you so much.
Thank you for this!! Is there a way to make this food safe? I’d like to make a charcuterie serving try!
Well I just tried birch because I grabbed a random piece from my stash ... total fail lol almost no ink stuck
So you WET it before taking off the picture . All the videos I’ve been watching just take it right off w no issues yet I cannot figure out how they do it ! I am frustrated . Maybe this is the KEY , wetting it ?! Let’s see if it works for me or else I just can’t keep trying . I tried mod podge, poly and a medium gel all unsuccessfully today . Looks amazing !!
Can you use osmo as a finisher?
Awesomeness
Great video.
Wow, this is great . I am a just starting I am going to try this
I’m interested in doing this on a guitar body. Also the ink not staying could be from the wood being closed cell or open...
Woah that would be so cool, I would love to see how that turns out! That's an interesting point, tbh I don't know much about that I will have to learn about the cells thanks for the tip 👍
Can you transfer a picture to a piece of wood that has been stained but not varnished? Thanks for the video.
Hi. Great video. Can you show the way to do it with an inkjet printer?
Our Upcycled Life would have a video or two on using an inkjet printer
How hard is it to put b/w pic on hardwood?
What kind of printer did you use?
how long can last the picture on the wood ? Nice video, thanks
Where can I get beautiful photos from?... I love this video
Wow thanks so much Cynthia! You can visit my website www.lucasmoorephotography.com for prints of my photos!
great video
What will happen if I use inkjet printed photos?
I was scrolling through the comments wondering this exact thing
Question... want to transfer a photo onto a black painted (store bought) frame. Will this method work for something painted and already finished? If you have an email I can send example, but basically I am going to take a picture and extend the picture into the frame. Maybe you can visualize? Picture, surrounded by a mat, but the edges of the picture extend beyond the mat onto the frame. Preferably a painted black frame. Think night shot, a mat to isolate the picture, then a frame to extend the edges of the picture. Black frame for darkness of night but color image added to it to extend the picture... I hope that makes sense?.?.
Why do some people that use Polycrylic easily peel off the paper with no mess? Can't seem to find a review that breaks down specific paper types.
Thank you for this video! When I tried this the paper seemed to bubble a little after I smoothed it down and it was too wet to smooth out again without tearing it. Any suggestions on how to fix that or is it normal?
So, what happens if you do use a inkjet printer and follow your steps?
Thank you so much - one of the best instructables I've seen! I am tempted to try it.
Completely off topic, but noticed your sofa...is it a Hans Olsen (Danish mid-century)? I have two Hans Olsen lounge chairs that look just the same - the rosewood arms (and typically chrome/nylon strapping at the back) are quite distinctive features.
Hey thanks for watching and commenting. I don’t think that the sofa is a Hans Olsen. We got it off Wayfair so I would say it’s definitely nothing too fancy haha.
good evening, could you please advise of the finish for the polycrylic, should it be better in satin, Gloss or matt?
thank you, great video