i have a question if i can her a little bit of tapping from my engine can i do this to stop it from make a straight noise like i think its the rod a little bit
Please do a video on how to set your carb up and adjust the airflow/idle screws. Can't find a decent video to explain it properly. More maintenance videos PLEASE
Sounds like a dumb novice question but when you are lining up the marks on the flywheel and the casing, which mark on the flywheel do you line up as there are several including a "T" and an "F" along with a few other marks. I'm new to all this and just want to broaden my knowledge. Thanks 😁👍🏼
Hey my car engine is running lil rough/Shaking n turning off and making a tapping noise do u think it could be my tappets that's making it run rough n turn off
@Dean Evs Yes it does my oil out bike just stalled when I was riding in a field and just would not start what I did to get it working back to its full potential was remove all the petrol and all of the engine oil, remove the carb and clean it out with white spirit, put the carb back together after clean and add back on to the bike, I then removed the spark plug and cleaned that with petrol and cleaned inside the hole, I then followed this guide to adjusting the tappets as shown in the video I then fitted everything back together and the bike started and went better than ever :)
Why did you set it on the f mark? I was told the t mark! T is tdc? F is for when it the fly wheel tells the bike to fire? I'm confused more? Am I as per usual over thinking it just my bike has the f and t?🙇🙇🙇
@@airbornerat I use T on my flywheel I guess its a upgraded flywheel as he says the notch nearest the letter so his may not have the T if u have a T use the mark at T
Hey guys I have a 125 Loncin pit bike and the rear caliper locked up on the disc and now it will only go backwards and then my dad thought it might need brake fluid but we put somem
you do not need to remove the stator cover or cam sprocket cover either. just remove both valve covers and spark plug. then kick over the engine until one valve opens then udjust the opposite valve.
jay7264 its very important that the bikes at tdc but u r right no need to take off cam sprocket cover just fly wheel needed also that bike must have been new and dry cause if the correct amount of oil was in it when he took off exhaust valve cover itd have pissed out
Blocked pilot jet? Clean carb out to start with. Check idle speed adjustment and air/fuel mixture screw. Turn it all way in till very lightly seats an then come back out 1.5 or 2 turns, the bike will now run to then be able to adjust precisely by listening to the engine.
my cam sprocket and flywheel don't line up together, if the flywheel is aligned with the engine marking then the cam isn't and vice versa. is this a problem, if so how do i fix it?
could really do with the same sticker set thats on this bike for my crf70 demon x d link 125 and i cant find them anywhere , could you point me in the right direction please, would be very much appreciated
I have a taotao 110 semi auto I know it's not the best bike but does anyone know anything about them and what brand parts I can buy or if its almost the same as all the rest
hello my pitbike has a problem with a oil leak on my spark plug tip inside it shuts down while riding and downshift a gear and I think it shouldn't be doing that it. would be great if u can help me with this I haven't ridden it for a long time
my bike has a lost of power the other day i was riding in 3 rd and she tried to lock up and theni shifted into 4th and she cut off im not sure why i changed the oil out but it was brand new and i refilled with newer oil and still had the same problem the bike smokes like a 2 stroke and its a 4 stroke it wont reach full not even half rpms and i changed the spark plug because it was black but im gonna take it apart maybe today to see whats up with it because she has never acted this way its an 4 month old bike and she just started acting like this yesterday
@@Morcego538 i own a kxd125 but i tuned the valves to .004 .006 like stated in this video but its doesnt sound right, but it ran fine no issues so i upgraded my carb from pz19 to the 26mm one and now it runs terrible so iv ordered another pz19 brand new carb
@@jameshalford4699 Maybe a 26 mm carb is to big for yours to much air intake, but I now that wen you install a bigger carb you need to change the jet screw to a bigger one, and install a bigger filter too, to let more air intake and more gas, mine is running on a mikuni 24 mm it’s the one that came from stock with her and an airfilter that looks like a UNI filter but I’m not sure if it is really a UNI, and it works really good alot of power, and makes a really good sound. There are carburetor kits that come with all this parts you need to change, the jet and all that.
@@Morcego538 i wasnt bothered about power mate im happy with it standard as i only use it for stunting in the car park i needed a new air filter so it was only like a extra £10 for a bigger carb so i thought id try it so i jusy ordered another pz19 which is the standard i beleive
That engine is different than a Honda cub engines cam timing is well different stomp use the z140cam higher lobes big valves he's going on the service manual from stomp if you check out the kayo website that is the manufacturer of stomp pit bike frames stomp get yx engine manufacturer to put a w racing brand cam in to it at the factory with stiffer springs and retainers basically the engines are race engines not standard by any means his engine is second generation yx engine you have 123 generation engines different years of production mate I checked with mine and mine has f,t on the flywheel t is spot on with the timing on the flywheel and cam but it is set at what he's talking about and mine is nearly brand new aswel
Hello! I watched a lot of videos on the subject. I do not speak English well. Your video can also be used without sound. The best! Thanks! Cheers!
Clean and quick maintence instructional, would love see more mate!
Your a star! Easy and well explained. Who’s disliking this video seriously!
Because he adjusted the valves on the fire mark rather then top dead centre
Because he adjusted the valves on the fire mark rather then top dead centre
Make more Of vidoes like this. Its Nice to have when you are a beginner in this 🤙🏻🤙🏻🤙🏻
Cheers lad helped me confidently adjust my valve clearances 👌
awesome video mate best one ive seen by far
Scott Madden I agree! thanks!
This backing track is SICK!!!
Best video on TH-cam thanks
good work on the vid and thanks for sharing for the rest of us mate.
thanks for the video. professional....definitely need those intake and exhaust valve clearances. Thanks!
Don’t adjust them to fire on the flywheel u want to set them at top dead centre
Thank you from UStralia brother
Thank you very much very helpful some idiot had totally set them well wrong before I got the bike.
Tryed this sound like a can of nails! inlet 0.02 exhaust 0.03/4 bikes perfect 👌🏽
What ccm
I went with 5thou outlet and 4thou inlet adjusted from cold 6thou for outlet makes them tap and sound like shit
Excellent video! Very well done and very helpful!
What are the tappet adjustment mm clearance on the z155 160cc
i have a question if i can her a little bit of tapping from my engine can i do this to stop it from make a straight noise like i think its the rod a little bit
Yo this video help a lot. Thanks !
damn thats a clean bike. well looked after
Mate that's a demo bike they sell everything you need to build your own bike from ground up 🇬🇧🇬🇧
Would you be able to do a top end rebuild on a yx 140. There are loads about but just to make sure we all do it the right way. Great video btw
Please do a video on how to set your carb up and adjust the airflow/idle screws. Can't find a decent video to explain it properly. More maintenance videos PLEASE
I have a stomp 140 and I was wondering if you are able to just turn the flywheel or do you use the kickstart?
If in gear I would imagine you can just rotate the rear wheel.
Very professional video with great advice, cheers mate!
Awesome video👍 keep it up mate
What are the torque specs on the engine covers?
عمل روعة جيد صديق كيف تركب تلك القطعة لتبريد الزيت وشكرا لك كثيرا انك مبدع
Hi guys I was just wondering if you could do a video on how to install a quarter twist throttle?
will those settings work on a YX110 mate?
He is wrong for the timing chain, need set at T line, not F line🤔
Mine is a yx140z2 my cam plate is different from his that's a old skool flywheel
That is a yx gen 2 engine the first generation yx 140 had two sprocket bolts😎🇬🇧
Mine is a first gen yx140
Super video thanks for sharing
Do I need to drain oil first?
What do u mean by the line closets to the lair I have a T mark and an F mark
Sounds like a dumb novice question but when you are lining up the marks on the flywheel and the casing, which mark on the flywheel do you line up as there are several including a "T" and an "F" along with a few other marks. I'm new to all this and just want to broaden my knowledge. Thanks 😁👍🏼
T
Ignore what he said line it up with the t
grate video thanks
Is it the same for a demonx 170 xlr2 thanks
عمل رائع جدا اخي لو سمحت ان تعمل فيديو كيف نعمل تلك مبرد الزيت وشكرا لك كثيرا
Perfect!
Looks like a very nice vid
I never have done this myself but i have seen it and its very similar to what i saw
Great vid bro🤘
Will these need to be set the same for a 125
Can be done with the gear lever still on just done it push it down out of the way
Hi do you know if its the same for yx160 motor? Great vid
My fly wheel marking doesn't match the marking on the cam sprocket. help?!
What is the song called?
i have a ssr110 would the work the same way you did yours
means its in gear if the bikes started and the back wheel is locked, the wheel will only move once the bikes running if thats what you mean?
Can i use the same measurements in the fillers you used im saying can i used the same 1s you used in this video
I have a 125cc pitbike engine
Which torque you’re using to close valve cover and flywheel cover?
180nm 😄
just tighten it until you cant lmfao
What does setting the timing mean does it have to do with the idleing ir the bike
Matching the rotation of the crank/movement of pistons to the valve movement. The tappet clearance is to allow for heat expansion.
is this a yx 140cc engine?
if you dont set them right can there be some popping ?
Will this be the same on 125 lit bike
Was that motor a piranha 140?
I respect the background music
Hey my car engine is running lil rough/Shaking n turning off and making a tapping noise do u think it could be my tappets that's making it run rough n turn off
@Dean Evs
Yes it does my oil out bike just stalled when I was riding in a field and just would not start what I did to get it working back to its full potential was remove all the petrol and all of the engine oil, remove the carb and clean it out with white spirit, put the carb back together after clean and add back on to the bike, I then removed the spark plug and cleaned that with petrol and cleaned inside the hole, I then followed this guide to adjusting the tappets as shown in the video I then fitted everything back together and the bike started and went better than ever :)
What if the cam is lined up but the flywheel is not?
Then your timing is out
So the letter F is the timing mark?
Why did you set it on the f mark?
I was told the t mark! T is tdc?
F is for when it the fly wheel tells the bike to fire?
I'm confused more? Am I as per usual over thinking it just my bike has the f and t?🙇🙇🙇
did you find out F or T?
@@airbornerat I use T on my flywheel I guess its a upgraded flywheel as he says the notch nearest the letter so his may not have the T if u have a T use the mark at T
would this stop a pitbike from starting?
Hey guys I have a 125 Loncin pit bike and the rear caliper locked up on the disc and now it will only go backwards and then my dad thought it might need brake fluid but we put somem
that is honda c 100 engine. legendary engine.
I have a ssr 125 by chance do you know the valve clearence
Can't seem to do it very hard to get to i got all mud droppigndown into it
does someone know where to found the AGB 29 user manual? I need to regulates the tappets but I don't have the necessary specifications...
Ruben Solano give me manual on my email
nabeelahme0786@gmail.com
i need a orion agb 37 crf1 manual mate
i have a stomp demon x 125cc this helped
what problems were you getting for you to adjust them mate, gonna do mine Saturday...... mines just overheating and being a bitch to start :L
the carb and tappets
hard to start
did it keep cuttig out after like 45min riding and donst start for like 3 hours its the offroad stomp i have thts doing it
This needs updating badly for your newer bikes!!!
you do not need to remove the stator cover or cam sprocket cover either. just remove both valve covers and spark plug. then kick over the engine until one valve opens then udjust the opposite valve.
jay7264 its very important that the bikes at tdc but u r right no need to take off cam sprocket cover just fly wheel needed also that bike must have been new and dry cause if the correct amount of oil was in it when he took off exhaust valve cover itd have pissed out
Hi can you tell me the tappet clearance for a demon x 160 please
Hi i have a 110cc semi auto pitbike have changed the piston and rings has got spark but won't run any ideas to try
Have you tested for spark by putting in against the engine?
Blocked pilot jet? Clean carb out to start with. Check idle speed adjustment and air/fuel mixture screw. Turn it all way in till very lightly seats an then come back out 1.5 or 2 turns, the bike will now run to then be able to adjust precisely by listening to the engine.
can I use 0.1 et 0.5 for dirt bike 125cc help pleazzzzzzzzz
my cam sprocket and flywheel don't line up together, if the flywheel is aligned with the engine marking then the cam isn't and vice versa. is this a problem, if so how do i fix it?
Did u solve it
could really do with the same sticker set thats on this bike for my crf70 demon x d link 125 and i cant find them anywhere , could you point me in the right direction please, would be very much appreciated
There is no crf70 dlink
I have 4 lines on my fly wheel I have 2 unmarked 1 with F and 1 with T in that order anyone know which one I line up with the fly wheel marker
Thankyou
What is the music
What do I set a 125cc pit pro tappets tk
welcome to pit bike . rekt
Cheers
I have a taotao 110 semi auto I know it's not the best bike but does anyone know anything about them and what brand parts I can buy or if its almost the same as all the rest
I just bought the same bike nd need help
+Dangerous Yvette what issues are you having with yours
When and how do you know if they need adjusted
My manual for my ycf sp2 150cc says 0.10 on both intake and exhaust??
Then do so if its in the manual just do it
hello my pitbike has a problem with a oil leak on my spark plug tip inside it shuts down while riding and downshift a gear and I think it shouldn't be doing that it. would be great if u can help me with this I haven't ridden it for a long time
george serrato timing bro
how does oil leak out your spark plug
when I start it. and while running it shuts off and I then remove the spark plug it's covered in oil
george serrato piston rings or valve stem seals
do I have to remove the top end?
.006 for both intake and exhaust
Barely need to remove anything and no shims. I wish all bikes where this simple to adjust
U know where I can get part for my pitbike. I have a 125cc apollo
Hi can you please help me with my demon 160x tappet clearance I need for it plz :)
ia ther any difrenc betven 140 and 125?
Theresa big differance on a 140cc to a 125 suprizingly miles more power
Anyone know how to set the cam mines popped out? Do I gave to adjust the tappets to install cam back in
I do this until i feel some resistance but it still makes a ticking noise from the head but all the vids I watch of the z40 140 make the noise.
No engine is silent
my bike has a lost of power the other day i was riding in 3 rd and she tried to lock up and theni shifted into 4th and she cut off im not sure why i changed the oil out but it was brand new and i refilled with newer oil and still had the same problem the bike smokes like a 2 stroke and its a 4 stroke it wont reach full not even half rpms and i changed the spark plug because it was black but im gonna take it apart maybe today to see whats up with it because she has never acted this way its an 4 month old bike and she just started acting like this yesterday
It might have too much oil in it or it needs new rings.
@@jimmywhitlow7174 it was the stupid timing chain ..
Gasket failure gaskets are cheap, could be piston ring , cheap fix 😊
How do I find top dead centre if I don't have a magneto?
undisputedattitude66 stick yer nob in exhaust
Haha
What kind of pit bike is that?
+Jr Martinez demon wpb
wht is the valve clerance for my pitboke terra-moto 125cc? does this measurements fit all pit bike cc??
Did u ever find out mate
No, I ended up not tuning the valves the bike is waiting for new parts, but wen I do I will come back and tell you. You own a terra-moto pit bike too?
@@Morcego538 i own a kxd125 but i tuned the valves to .004 .006 like stated in this video but its doesnt sound right, but it ran fine no issues so i upgraded my carb from pz19 to the 26mm one and now it runs terrible so iv ordered another pz19 brand new carb
@@jameshalford4699 Maybe a 26 mm carb is to big for yours to much air intake, but I now that wen you install a bigger carb you need to change the jet screw to a bigger one, and install a bigger filter too, to let more air intake and more gas, mine is running on a mikuni 24 mm it’s the one that came from stock with her and an airfilter that looks like a UNI filter but I’m not sure if it is really a UNI, and it works really good alot of power, and makes a really good sound. There are carburetor kits that come with all this parts you need to change, the jet and all that.
@@Morcego538 i wasnt bothered about power mate im happy with it standard as i only use it for stunting in the car park i needed a new air filter so it was only like a extra £10 for a bigger carb so i thought id try it so i jusy ordered another pz19 which is the standard i beleive
valve clearance in 0.10 ex 0.15 or maybe in 0.10 ex 0.10?
how did you make that stand?
i have a 150cc chinese bike and i have no idea what the clearences need to be!?!?
wat is this for
My vavles are too tight can not even put feeler underneath. Help !!!
Well you got to open them first so you can get the feelergauges in and then you tighten the adjustment,🤦♂️just use your common sense man
Your timing mark looks like an F for firing that can be confusing because you definitely do not want to get T for timing and F for firing confused🤔
Why didn't you do it at operating temperature?
Lachlan Horne Expands and contracts with heat. Doing it cold guarantees a proper measurement.
Very inaccurate. 0.04 and 0.06 will make your motor tick like a time bomb. Always go 0.02 or 0.03 like Honda did.
That engine is different than a Honda cub engines cam timing is well different stomp use the z140cam higher lobes big valves he's going on the service manual from stomp if you check out the kayo website that is the manufacturer of stomp pit bike frames stomp get yx engine manufacturer to put a w racing brand cam in to it at the factory with stiffer springs and retainers basically the engines are race engines not standard by any means his engine is second generation yx engine you have 123 generation engines different years of production mate I checked with mine and mine has f,t on the flywheel t is spot on with the timing on the flywheel and cam but it is set at what he's talking about and mine is nearly brand new aswel
@@gavinmcvey8177 So when I set the timing do I use the F mark or the T mark on the flywheel as mine also has both markings ? Thanks for your time . 👍🏻
Times have changed so it depends on the company and motor design
@@katluke T
i thought that