Did you fix your car issues? Let us know in the comments below, and maybe you can help someone else with a bad crankshaft position sensor! Don't forget to like the video and subscribe to our channel! More CPS sensor information: mechanicbase.com/engine/crankshaft-position-sensor-symptoms/ Website: mechanicbase.com/
I need help please. I've tried 3 different sensors and even tried another dme on my 2007 e60. I can't get any voltage drop on sensor running magnet across it.
When the crankshaft sensor starts to go bad, it starts showing symptoms when it's cold. This is my own experience. You just can't find that information anywhere. You could easily think that there is a problem with the mixture ratio, although the crankshaft sensor may be the real culprit and may work well in warm weather, but at a certain degree of frost it starts to show symptoms.
@@buckhayes2104 And the freezing point where the symptoms start can be very sharp. It may be that the car works well, for example, at -13 c degrees and -14 c doesn't work anymore very well. In severe frosts, it sounded as if the ignition was completely out of place and the car would only idle at about 500rpm and engine may not be able to take more revs.. The car smoked a lot and the exhaust smelled strange.
@@buckhayes2104 Here's a link to a video where you can hear how the car's engine was doing before the fault was found. I myself had two faults. The crankshaft sensor and then the air mass meter. But the crank sensor was the main culprit. The faulty air mass meter made jerks only at higher revs while driving. But didn't affect the idle and didn't make it difficult.
Thank you so much for this very helpful and informative video! We have a 2013 Equus and it's giving us the exact problems you described in this video. By being your video, it's letting my husband know he's on the right track, and confirming his suspicion of what's going on with the car. Thank you so much for this helpful video!
GREAT VIDEO BRO. After winter my batterie in my S2000 died, I replaced it and the car started, but it didnt run smooth. The power was low, revs fell off and missfiring started and it cut out. I thought that was probably the Ignition coils. Replaced them and the car ran better but vibrations were getting higher the warmer the engine got. Then I got a tool to read the fault and it said Crankshaft position sensor. I erased it, it wont start anymore but now i definetly know why. It all makes sense after watching your video. I really appreciate your Content
Thank you 🙏. This is the best explained video, I have every seen anyone put on here..... You mentioned every detail that my car is doing and when it's doing..... (Thank You) Plz.. don't change we need a guy like you to help us all...
Brother man thank you so much out of all the videos you broke down how was supposed to be broken down, very informative and straight to the point in detail💯💯🙏🏾🙏🏾
My problem is a P060A On my 2008 civic ,I think it’s more of a computer internal memory , BUT you ARE very good at explaining that particular sensor . Sounds like an honest guy
Big thumbs up for mentioning some manufacturers put it on timing belt side. Unfortunately, my Civic is on timing belt side so it was big bucks to replace 😢
On very rare occasion my panel lights all come and the car will stall , it then starts up as normal ,sometimes it get a No Crank issue and sometimes Cut out after Starting up Car is CLK 220 CDI 2007 with 250000 miles on the Clock other wise all good Best Regards John
Thanks for sharing these great videos! I'm trying to find the location of the Crankshaft Position Sensor for the 2011 Benz B200 and wondering if you can help. Thank you!
Thank you for confirming the symptoms. Seems manufacturers can pump any random fault code out and they don't mean the same thing from car to car. Seems P1337 on Citroen DS3 does point to crankshaft position sensor. Getting to it though is somewhat of a challenge and I don't seem to be able to find anything that suggests correctly where it is.
@@louwscustomsza I'm having same problem. Mine just cranks. I've changed the vvt solenoid, solenoid filter, camshaft sensor, fuel pump, starter, battery, a couple sparks plug... It's still cranks but no start. I have no codes showing when I plug the OBD. I'm thinking it's the crankshaft sensor tho.
@chriskramp5174 My problem was the metal plate that came after the crank sprocket. Apparently, the letter on it is supposed to be faced outside(B)(F). The crank sensor gets its reading from it
I guess I'm going thru the same issue from what 3 mobile mechanics told me what else can It be preventing it to start I was in middle of grocery shopping dropped meat off at home went to finish shopping it haven't started in 6 months I need help bad
My 2017 Nissan patrol super safari starts rough making weird sound, fuel efficiency is lower than the norm, RPM plays around at idle, has no check engine light on (bought it used, suspect foul play). Used my scan tool and got a confirmed P0335 engine speed sensor which I assume is the same as crankshaft position sensor. Cleared it and and it still came back the same. Not sure where the crankshaft sensor is to inspect it, and the manual doesn't mention it. Its worth mentioning I also have a confirmed C1130 (ABS system code).
I just replaced all 3 on my nissan xterra a year ago, and I have a code p0335 pop up now, do I have to replace all 3 again or just the crankshaft sensor? Thanks
I have 1989 MK1 VW Golf GTI Convertible with a DX type of engine, can you assist by giving me instructions where to locate it. Please attach a picture of it. Thanks, Costas.
Good information about the starting symptoms that I haven't seen elsewhere. My 2007 Chrysler T&C had trouble starting hot two or three times. I assumed the starter was going. There were no codes. Then today it threw a P0017 and started running bad - almost stalling out every time I came to a stop and responding slowly to the accelerator pedal. Will check the sensor tomorrow, but it seems quite likely. So I'm guessing the starting hot issues can be an early warning.
Thanks, I have a ml350, 4mactic, 2011 , try to do , dc , inspection and my engine light is on and the 7:127:12 smog pump wasn’t bad so , intake camshaft cylinder the 2 on top will be replaced to see if this help my engine light to go off, the relay switch I’m going to change ! Hope you can give me some quick advice !
Hi there mechanic base,i have a vw passat b6,saloon ,1.9 Tdi ,2007 and since a week dont start. On the tester showed me the camshaft sensor.Can be this problem to no start? If yes where is the sensor located? Thanks and waiting for your reply
Hi can you please advise position of Crankshaft sensor in a 2005/6 Ford Fiesta Trend 1600 manual petrol 3 door As well as a Volvo C30 T5 R-Design automatic 2012 Will really appreciate
Can this information be applied to motorcycles as well? My kawasaki z900 - 2017 sometimes just wont start and I've gotten the code P0335 on it. Sometimes it just wont start for at least 6-7 tries but then it works just great. However, after riding it for some time , if I turn of the ignition it wont start which has left me stranded a couple of times (sorry for my english, I'm from Sweden) Great informative video btw!
Only thing I'm going to add here is that you can get no misfires and no codes and still have a bad crankshaft sensor! Mine has done it twice. No misfires no codes both times. But mine is a 99 and that may play a LARGE part of the missing codes. I cannot get OE sensors for mine and am forced to go with cheap ones that don't last. Only do OE if you have that option!
Thanks for the informative video! Vehicle: 2013 Hyundai, Azera. I am told this part needs to be replaced. There were numerous codes that presented w/ the main key fob. After I asked, should you check the communication w/ the other key fob (extra), they check and said that there was a "hidden code." The other key fob registered a code for this. It does not sound for sure that this is the fix, but they said it could clean many of the other codes. Do you think I should have to pay for a 2nd diagnostic hour when they should have initially asked if there were 2 key fobs? I've kept the car up and have never had any prior issues. Welcome your feedback.
I drive a chevrolet camaro v6 Lt 2010 I'm not sure where my crankshaft position sensor would be located?not sure what tools I would need to do the job myself simple rachet etc.
Greetings, I own a 1993 C3500 7.4 Truck & I cannot locate the crankshaft Position Sensor (CKG). I've seen references of between Harmonic Balancer & Timing Cover, in the Block above the oil pan, back of the block, or inside the Distributor. I've looked carefully, no loom wires, no port in timing cover, & I replaced the OEM Distributor with new OEM unit. Vehicle timing set to 4 degrees before TDC. Verified all spark plug & fuel inj. Vehicle starts, stalls, back fires.
My car has a tsi 2.0 petrol engine, basically a golf GTi engine. Drives great, but sometimes when it's warmed up, it will struggle to start, and it will the start when I let it cool down? Is it this sensor I need to change?
Sir, great video, but I need your help on where my Crankshaft position sensor on my 2017 toyota camry le gas, One mechanic said it was at my right hand side located front tire where the cover is. Can you please help. Larry Chicago
Porsche Cayenne GTS - Along with Crankshaft sensor my electrical devices are not working or affected could this also be cos of crankshaft? Or is it something else? The driver seat window is slow and the roof doesn't close completely - There is a small gap and the LCD system bought last year also failed or not working.
Hello, can a faulty Crank Position Sensor causes anti theft security light to remain blinking even after you have inserted the ignition key in car key hole???
Hi mr. Sam! I've a Opel Corsa C 1.4 16v the engine start good, any codes or ligths on the dashbord appers, but after 15 or 20 minutes after the start and when the engine get temperature 90°c the engine cut out, after that, I trying to restart it, but the half of the dashbord is off... no check engine light, no oil, no inmo, nothing light are ON... after that 1 hour and when the engine is cold or warm, the engine start again normally. Do you think that the sensor is damaged or the connector o wires? Thanks for your comments back. Regards!
My car is very difficult to start for the first time, after about 20 seconds it starts, especially when it is cold. and after that every start goes well, so only the 1st start. Battery ignition coil spark plug has been replaced, what do you think? I would like to help, can it be done by the sensor that only works the 1st time
so i did get the p0335 code and my car has been stalking or stopping on me and even check engine comes and go . so they say it’s the crankshaft sensor. u guess my question is how do you know if it’s the front or back crankshaft sensor . i have a 2014 hyundai sonata @mechanicbase
My car is 2007 Volvo xc70 gives me code ; P0503 (rpm signal low) and P2160. Is it still about crankshaft position sensor ? I wanna do it myself and I wanna buy the right part. (Btw I know that P2160 is about wheel speed sensor) thank you ❤
My car doesn’t throw a code. It'll run sometimes, then after even a short break, if I walk out or take a minute outside with the engine off, it does not turn back on. I'll have to probably wait 30 mins to get it back on. Any advice?
I need help with my e60. When I plug in sensor the 5 volts goes down to 2.5v. It's got good 12v power and good ground from dme. I tried to see any volt drop with a ociloscope. I tried 3 different sensors and 2 different dme.
Just found this. 1998 honda prelude no start. Replaced distributor, rebuild starter, replaced oem ngk spark plugs. Got no codes. Just did timing belt change with all related components about 6 months ago gates kit with japan parts.
my battery is getting low plus getting p0851 code and p0335 code in 2010 subaru forester. My mechanic said no need to change crank shaft sensor so he changed only neutral switch. But still issue remains. Thanks
Did you fix your car issues? Let us know in the comments below, and maybe you can help someone else with a bad crankshaft position sensor!
Don't forget to like the video and subscribe to our channel!
More CPS sensor information: mechanicbase.com/engine/crankshaft-position-sensor-symptoms/
Website: mechanicbase.com/
Can't find my crankshaft position sensor in my v70 2.5t volvo
I need help please. I've tried 3 different sensors and even tried another dme on my 2007 e60.
I can't get any voltage drop on sensor running magnet across it.
1:32
Hello name Joey I like to know where would my crank shaft position be at I have a 2007 buick lucerne cxl v6 engine
Is this a pcv vale
When the crankshaft sensor starts to go bad, it starts showing symptoms when it's cold. This is my own experience. You just can't find that information anywhere. You could easily think that there is a problem with the mixture ratio, although the crankshaft sensor may be the real culprit and may work well in warm weather, but at a certain degree of frost it starts to show symptoms.
Tell me more.
@@gottahavegoalsset ?
This explains my frustrations OMG!! This is very important information .
@@buckhayes2104 And the freezing point where the symptoms start can be very sharp. It may be that the car works well, for example, at -13 c degrees and -14 c doesn't work anymore very well. In severe frosts, it sounded as if the ignition was completely out of place and the car would only idle at about 500rpm and engine may not be able to take more revs.. The car smoked a lot and the exhaust smelled strange.
@@buckhayes2104 Here's a link to a video where you can hear how the car's engine was doing before the fault was found. I myself had two faults. The crankshaft sensor and then the air mass meter. But the crank sensor was the main culprit. The faulty air mass meter made jerks only at higher revs while driving. But didn't affect the idle and didn't make it difficult.
Thank you so much for this very helpful and informative video! We have a 2013 Equus and it's giving us the exact problems you described in this video. By being your video, it's letting my husband know he's on the right track, and confirming his suspicion of what's going on with the car. Thank you so much for this helpful video!
same happend to me, but never seen the camshaft sensor error, only random missfires errors.
Informative, no bs. It was nice knowing what tools I would need. Well done.
GREAT VIDEO BRO. After winter my batterie in my S2000 died, I replaced it and the car started, but it didnt run smooth. The power was low, revs fell off and missfiring started and it cut out. I thought that was probably the Ignition coils. Replaced them and the car ran better but vibrations were getting higher the warmer the engine got. Then I got a tool to read the fault and it said Crankshaft position sensor. I erased it, it wont start anymore but now i definetly know why. It all makes sense after watching your video. I really appreciate your Content
🫡🫡
Thank you 🙏. This is the best explained video, I have every seen anyone put on here..... You mentioned every detail that my car is doing and when it's doing..... (Thank You) Plz.. don't change we need a guy like you to help us all...
Brother man thank you so much out of all the videos you broke down how was supposed to be broken down, very informative and straight to the point in detail💯💯🙏🏾🙏🏾
Thanks for your clear explanation, i have an mercedes R350 and i have the same symptoms. I`ll look it.
My problem is a P060A
On my 2008 civic ,I think it’s more of a computer internal memory ,
BUT you ARE very good at explaining that particular sensor .
Sounds like an honest guy
I thank you for describing the symptoms so detailed, as I have exactly the named problems. Thank you!
Same!
Big thumbs up for mentioning some manufacturers put it on timing belt side. Unfortunately, my Civic is on timing belt side so it was big bucks to replace 😢
I almost replaced the ECM when it was just sludge and metal buildup on the CPS. Thanks you just saved me a couple hundred dollars.
Glad to hear that👍
If you had metal build up in your crank sensor you have other issues asswell
Was there no error code?
Hey mine was dirty do I clean the sensor with brake cleaner and the slot as well where the sensor goes ? Or just the sensor?? Please help
@@vladt6038hey how do I clean it ? Like do I clean the slot where the sensor goes as well with brake cleaner or JUST the sensor?
On very rare occasion my panel lights all come and the car will stall , it then starts up as normal ,sometimes it get a No Crank issue and sometimes Cut out after Starting up
Car is CLK 220 CDI 2007 with 250000 miles on the Clock other wise all good
Best Regards
John
Thank you great video! Very helpful! I got the same issue when the engine is warm.
Yes, that could be the crank sensor. Do you have any codes?
Thank you; this helped me to figure out that my sensor is bad
Thanks for sharing these great videos! I'm trying to find the location of the Crankshaft Position Sensor for the 2011 Benz B200 and wondering if you can help. Thank you!
Thank you for confirming the symptoms. Seems manufacturers can pump any random fault code out and they don't mean the same thing from car to car. Seems P1337 on Citroen DS3 does point to crankshaft position sensor. Getting to it though is somewhat of a challenge and I don't seem to be able to find anything that suggests correctly where it is.
I have a 2015 Nissan Altima where is my camshaft sensor or crank sensor located thank you so much for your helpful video.
2.5 engine? If yes, it should be near the transmission end, on the back of the engine (facing the firewall).
on my Toyota Corolla it's the VVT soliniod, but same symptoms , great explanation in the video
Did it cut off fuel and spark? My corolla won't start just cranks. It cut off fuel and spark
@@louwscustomsza I'm having same problem. Mine just cranks. I've changed the vvt solenoid, solenoid filter, camshaft sensor, fuel pump, starter, battery, a couple sparks plug... It's still cranks but no start. I have no codes showing when I plug the OBD. I'm thinking it's the crankshaft sensor tho.
@chriskramp5174 My problem was the metal plate that came after the crank sprocket. Apparently, the letter on it is supposed to be faced outside(B)(F). The crank sensor gets its reading from it
Thank you boss, ur symptoms are same as mine, I think the sensor is broken. Engine switches itself off once warmed up
I guess I'm going thru the same issue from what 3 mobile mechanics told me what else can It be preventing it to start I was in middle of grocery shopping dropped meat off at home went to finish shopping it haven't started in 6 months I need help bad
My 2017 Nissan patrol super safari starts rough making weird sound, fuel efficiency is lower than the norm, RPM plays around at idle, has no check engine light on (bought it used, suspect foul play). Used my scan tool and got a confirmed P0335 engine speed sensor which I assume is the same as crankshaft position sensor. Cleared it and and it still came back the same. Not sure where the crankshaft sensor is to inspect it, and the manual doesn't mention it.
Its worth mentioning I also have a confirmed C1130 (ABS system code).
All those symptoms correspond to a bad CKP sensor.
I just replaced all 3 on my nissan xterra a year ago, and I have a code p0335 pop up now, do I have to replace all 3 again or just the crankshaft sensor? Thanks
I have 1989 MK1 VW Golf GTI Convertible with a DX type of engine, can you assist by giving me instructions where to locate it. Please attach a picture of it. Thanks, Costas.
Good information about the starting symptoms that I haven't seen elsewhere. My 2007 Chrysler T&C had trouble starting hot two or three times. I assumed the starter was going. There were no codes. Then today it threw a P0017 and started running bad - almost stalling out every time I came to a stop and responding slowly to the accelerator pedal. Will check the sensor tomorrow, but it seems quite likely. So I'm guessing the starting hot issues can be an early warning.
Thanks, I have a ml350, 4mactic, 2011 , try to do , dc , inspection and my engine light is on and the 7:12 7:12 smog pump wasn’t bad so , intake camshaft cylinder the 2 on top will be replaced to see if this help my engine light to go off, the relay switch I’m going to change ! Hope you can give me some quick advice !
Perfect video.. I fixed it. Great work.
Thank you this is exactly what’s been going on
If the sensor is bad, will you have a problem with idle up high when your feet is barely on the gas. 2010 Cadillac srx
Hi there mechanic base,i have a vw passat b6,saloon ,1.9 Tdi ,2007 and since a week dont start. On the tester showed me the camshaft sensor.Can be this problem to no start? If yes where is the sensor located? Thanks and waiting for your reply
Where is the crankshaft position sensor located on a 2014 Audi Q5? Thank you, Marcus
Hi can you please advise position of Crankshaft sensor in a
2005/6 Ford Fiesta Trend 1600 manual petrol 3 door
As well as a
Volvo C30 T5 R-Design automatic 2012
Will really appreciate
Very informative video Sir. Thanks for the knowledge too.
I am looking for the crank position sensor for a 1996 Nissan quest GXE with the 3.0 V6
How to find the crankshaft position sensor in the Honda Civic 2012LX? Where is the location?
Can this information be applied to motorcycles as well? My kawasaki z900 - 2017 sometimes just wont start and I've gotten the code P0335 on it. Sometimes it just wont start for at least 6-7 tries but then it works just great. However, after riding it for some time , if I turn of the ignition it wont start which has left me stranded a couple of times (sorry for my english, I'm from Sweden) Great informative video btw!
Yes, it's quite likely. That sounds like a crank sensor.
Only thing I'm going to add here is that you can get no misfires and no codes and still have a bad crankshaft sensor! Mine has done it twice. No misfires no codes both times. But mine is a 99 and that may play a LARGE part of the missing codes. I cannot get OE sensors for mine and am forced to go with cheap ones that don't last. Only do OE if you have that option!
Thanks for the informative video!
Vehicle: 2013 Hyundai, Azera. I am told this part needs to be replaced. There were numerous codes that presented w/ the main key fob. After I asked, should you check the communication w/ the other key fob (extra), they check and said that there was a "hidden code." The other key fob registered a code for this. It does not sound for sure that this is the fix, but they said it could clean many of the other codes. Do you think I should have to pay for a 2nd diagnostic hour when they should have initially asked if there were 2 key fobs? I've kept the car up and have never had any prior issues. Welcome your feedback.
Looking for location of the crankshaft sensor in my 2005 Dodge Caravan. Do you know of a drawing online for the location?
I drive a chevrolet camaro v6 Lt 2010 I'm not sure where my crankshaft position sensor would be located?not sure what tools I would need to do the job myself simple rachet etc.
Greetings, I own a 1993 C3500 7.4 Truck & I cannot locate the crankshaft Position Sensor (CKG).
I've seen references of between Harmonic Balancer & Timing Cover, in the Block above the oil pan, back of the block, or inside the Distributor. I've looked carefully, no loom wires, no port in timing cover, & I replaced the OEM Distributor with new OEM unit.
Vehicle timing set to 4 degrees before TDC. Verified all spark plug & fuel inj.
Vehicle starts, stalls, back fires.
Is it best to change the crankshaft and camshaft position sensors at the same time?
Have a VW T4 Cavalry Van. Were is the crank shaft sensor positioned in the Engine. As what you explained in your Video, is my Van.
Hey, which engine do you have?
Can you tell
Me the cranckshaft position sensor lovation on volvo S90 2017 diesel saloon
I have a 1996 Ford explore and I can't find the crankshaft senor bank 1 tank's for your help
Hey so I'm having trouble finding the crankshaft sensor on my 2010 GMC terrain sle 3.0l AWD can you possibly help by chance ?
I have hyundai Veloster 2015 While driving stop .Already i change Fuel Pump ,Map Sensor , Oxgen Sensor , Still Same Issue facing While driving ...
My car has a tsi 2.0 petrol engine, basically a golf GTi engine. Drives great, but sometimes when it's warmed up, it will struggle to start, and it will the start when I let it cool down? Is it this sensor I need to change?
06 Chevy cobalt where is the cam shaft and crank shaft position Sensors located
I have a Opel Combo 1.7 di 2002 car, it only starts in the morning and during the day it doesn't start, could this sensor be the problem?
Sir, great video, but I need your help on where my Crankshaft position sensor on my 2017 toyota camry le gas, One mechanic said it was at my right hand side located front tire where the cover is. Can you please help. Larry Chicago
Porsche Cayenne GTS - Along with Crankshaft sensor my electrical devices are not working or affected could this also be cos of crankshaft? Or is it something else?
The driver seat window is slow and the roof doesn't close completely - There is a small gap and the LCD system bought last year also failed or not working.
Just want to know can you swap the magnetic crankshaft sensor to a hall affect sensor
Where is the crankshaft sensor located for a 2015 chevy equinox? Please and thank u
Dear friend,my vehicle is 2020 Mazda bt50. It suddenly hard starts right after the fuel filter was replaced
Trying to fix a 2013 hyundai genesis 3.8 need to locate the crankshaft sensor
where are these on a 2012 Land Rover LR4? I think they may be right on the front but totally unsure
Thank you. Sounds like every big part of the engine has a sensor!
Great video! I was looking for one on 05 Chrysler Pacifica I have not found yet can you help?
Hello, can a faulty Crank Position Sensor causes anti theft security light to remain blinking even after you have inserted the ignition key in car key hole???
Got a hilux 1kd engine. Put in a new engine,but it not starting can error codes be causing it from reading the new engine?
I have a 1996 Ford explorer V8 where would the crank sensor be located at
Hi mr. Sam!
I've a Opel Corsa C 1.4 16v
the engine start good, any codes or ligths on the dashbord appers, but after 15 or 20 minutes after the start and when the engine get temperature 90°c the engine cut out, after that, I trying to restart it, but the half of the dashbord is off... no check engine light, no oil, no inmo, nothing light are ON... after that 1 hour and when the engine is cold or warm, the engine start again normally. Do you think that the sensor is damaged or the connector o wires?
Thanks for your comments back.
Regards!
That could definitely be the crank sensor.
My car is very difficult to start for the first time, after about 20 seconds it starts, especially when it is cold. and after that every start goes well, so only the 1st start. Battery ignition coil spark plug has been replaced, what do you think? I would like to help, can it be done by the sensor that only works the 1st time
I want to know specifically for 2020 Mazda bt50 3.2 ltr turbo diesel engine
I have a 2008 Cadillac SRX 3.6 all wheel drive can you tell me where the Crankshaft sensor is located on my engine?
Can a faulty Crankshaft Postion Sensor cause a total non cranking ie the self starter not spinning?
In a MBENZ SLK 320 R170 465 2001 MODEL?
Where can I find the crankshaft sensor for my Nissan Sunny 2022?
so i did get the p0335 code and my car has been stalking or stopping on me and even check engine comes and go . so they say it’s the crankshaft sensor.
u guess my question is how do you know if it’s the front or back crankshaft sensor . i have a 2014 hyundai sonata @mechanicbase
I have a..1993 GMC Sierra 1500 crank will not start replace alternator and spark plugs...is there a sensor on this vehicle
I have a 2020 Chevy Malibu lt 1.5 crank and crank but no start and rpm gauge not moving while cranking
I have a 1997 ford F350 diesel 7.3 powerstroke where is the crankshaft sensor located
Hi, I am trying to find the location of the crankshaft sensor on a bmw f15 530d n57t thanks
My 06 colorado idled really rough and when it got 10° or below it would not start at all but would crank... It was a faulty crankshaft sensor
Where to find Crankshaft position sensor chevy captiva sport 2013 v4. Thank you. It feels low power? Great inf.
Hello. Where would this be located on a 2010 Suzuki Kizashi?
Which engine do you have?
Please, i want to know the position of crankshaft sensor in my Toyota highlander 2006 highbrid
06 cobalt where is the crankshaft and camshaft sensors located
Thanks.where is the crankshaft position sensor connector in a 2005 isuzu 4jh1 truck?
Golf Mk5 gt170 BMN is the sensor on belt or in oil filter housing ?
Hello, thanks for this. Can you please share where the position of the crankshaft is on Renault Kangoo 2003 Automatic transmission? Best
Hi. Which engine?
@@MechanicBase 1.6 16V (95 Hp) Automatic
My car is 2007 Volvo xc70 gives me code ; P0503 (rpm signal low) and P2160. Is it still about crankshaft position sensor ? I wanna do it myself and I wanna buy the right part. (Btw I know that P2160 is about wheel speed sensor) thank you ❤
Where can I find it on Hyundai Sonata 2013 ?
Thank you
Replacing mine with a duralast, I would say it depends on the manufacturer. The duralast is better than the oem original lol.
We can't find my crank position sensor on my 2002 Hyundai Sonata 4.2 liter Could you help please and thank you?
Where is the crank shaft located in a Chrysler 200 year 2013
Kan det bli trykk på motor med dårlig sensor?
Where on2007 Mitsubishi eclipse 2.4 manual engine is the crankshaft position sensor located
I have a2002 chevy avalanche 4×4 2500 8.1 ingene
Where located crankchaft position sensor
This video was very valuable & informative Thank You 👏
Where will I find it on my 2000 gmc sonoma 4.3 vortex
My car doesn’t throw a code. It'll run sometimes, then after even a short break, if I walk out or take a minute outside with the engine off, it does not turn back on. I'll have to probably wait 30 mins to get it back on. Any advice?
Cranks, but doesn't start? That sounds like a crankshaft sensor. Which car?
Not sure if I have one w124 230e not getting the vehicle started
I need help with my e60. When I plug in sensor the 5 volts goes down to 2.5v.
It's got good 12v power and good ground from dme.
I tried to see any volt drop with a ociloscope. I tried 3 different sensors and 2 different dme.
Just found this. 1998 honda prelude no start. Replaced distributor, rebuild starter, replaced oem ngk spark plugs. Got no codes. Just did timing belt change with all related components about 6 months ago gates kit with japan parts.
Toyota rav 4 2007 gas 4x4 2.0. Where do i find the crankshaftsensor?
I have oil in the connections at the female end and male end. What do I do?
my battery is getting low plus getting p0851 code and p0335 code in 2010 subaru forester. My mechanic said no need to change crank shaft sensor so he changed only neutral switch. But still issue remains. Thanks
Looking for my Crankshaft sensor in a 2017 Chevy Equinox V4 engine.
i have a 2007 ford expedition but I can't find the crank sensor?where is it located??
Very informative, thank you!