Nice work, I had a tear on the inside. Sealed it up with super glue like you did, and then added a layer of waterproof gorilla tape on either side. It's held up for a year so far!
Going to give this a go today as we also have an LG washing machine with a similar leak. Despite the fact that the machine is in warranty LG are refusing to fix.
Superglue is the worse thing you can use, better to get some Polyurethane sealant, you can also get it in grey. The sealant is rubbery and stretchy. Just use baking paper with some painters tape.
@B0r0 it doesn't need to be rubbery and stretchy; it needs to connect very thin things that are rubbery and stretchy. Also, it worked great. Polyurethane (non-expanding) sealant would probably also work, just with more mess and slower drying time.
you are correct in the best way to repair this problem. Use Loctite PLS30 EPDM sealant to re-construct the washer boot. works perfectly and is a PERMANENT fix. It will outlast the appliance.
I tried this and made sure to buy the black roofing sealant (Loctite PL Roof & Flashing from HD), used waxed paper, and allowed it to cure for 4 days. Did this twice and both times, I barely touched the area to clean it up like in the video and the sealant fell right out as if it wasn’t actually adhering to the rubber gasket. I made sure it was 100% dry and everything before applying and followed the video step by step. I also tried smearing the sealant further to the sides to hopefully grasp onto the gasket more but to no avail. What could I be doing wrong? Thank you for any more advice!
@Fern Home & LifeStyling Failed! I had a big chunk missing from my seal. This is probably best for a tear or crack. I'd give it a shot if your damage looks anything like it looks in the video. It'll cost a lot less than getting a new unit if you are successful.
@@TheSnekkerShowWith the exterior electrical tape would the tape still curl after every wash cycle and need to be restuck. Or is that the exact reason you're using the exterior tape to limit that step.
@zg-shred I suspect, but haven't tested, that an exterior grade electrical tape would last much longer because the water wouldn't affect it as much. But again, this is only intended to be a temporary solution so the machine can still be used while a long-term repair is being figured out.
Why not just remove the gasket/seal with the comprised spot and relocate to the top where water is not in contact with the seal until the new one arrives? Nice fix I will have to say!
I have a slightly different problem. I installed a new gasket. Ran washer and it leaks from the front where the seal meets the door. it looks like because it was folded while in the box, the fold was right at the point where the bottom arrow is, so it indents there and lets water by. i don't know if it will eventually shape out to fit or if i should return now.
OH Man you r fok1ng Genius , thanks for share , for sure you help a lot of people with this video , Im going to fix mi washer machine this weekend , greetings from San Jose Ca
The door seal could also be leaking from the inside leading one to believe it's not the seal but perhaps a hose or maybe the pump. That's what happened to mine. After removing the lower cover I started a load, and found the leak in the seal on the inside. Hope this helps someone.
I have LG wm2277hw in my house, we found it when we moved in. It has been almost 9 years we have been using the machine. Lately we found pieces of plastic clogging up in the drain filters and it turned out to be the plastic drum that enclosed the stainless drum started to crack and chips off. My guess is, this machine about 19 years old, I guess yours might have the same fate. It is time for a new machine.
I can answer a little better now after confirming that the job would go pretty much as I expected. The whole thing took about six hours, frequently interrupted by dad responsibilities, and I also decided to clean, treat, and paint some rusted parts around the detergent tray, and also needed to unclog a drain line. Having done it once now, it would probably take 30-45 minutes the next time, assuming no additional maintenance.
@@TheSnekkerShow Whine about it...WHAT??? All, I asked is why you didn't change out the gasket, and all you want to be is a tuff guy. Would love to see you call me a whinner to my face.
Nice work, I had a tear on the inside. Sealed it up with super glue like you did, and then added a layer of waterproof gorilla tape on either side. It's held up for a year so far!
The gorilla tape do you just tape just where it tear ?? From inside out ?😊
Going to give this a go today as we also have an LG washing machine with a similar leak. Despite the fact that the machine is in warranty LG are refusing to fix.
Thank you for the tip. I was about to have too much time on Memorial Day weekend.
Omggg TY SOO MUCH I CANNOT AFFORD TO REPLACE OR A SERVICE TECH 🙏🏿
I used superglue an marine silicon seal and got it down from a constant trickle to just an occasional few drops.
This is probably in my future too. Great temp repair.
Superglue is the worse thing you can use, better to get some Polyurethane sealant, you can also get it in grey. The sealant is rubbery and stretchy. Just use baking paper with some painters tape.
@B0r0 it doesn't need to be rubbery and stretchy; it needs to connect very thin things that are rubbery and stretchy. Also, it worked great. Polyurethane (non-expanding) sealant would probably also work, just with more mess and slower drying time.
you are correct in the best way to repair this problem. Use Loctite PLS30 EPDM sealant to re-construct the washer boot. works perfectly and is a PERMANENT fix. It will outlast the appliance.
simple matter-of-fact presentation. Good
I tried this and made sure to buy the black roofing sealant (Loctite PL Roof & Flashing from HD), used waxed paper, and allowed it to cure for 4 days. Did this twice and both times, I barely touched the area to clean it up like in the video and the sealant fell right out as if it wasn’t actually adhering to the rubber gasket. I made sure it was 100% dry and everything before applying and followed the video step by step. I also tried smearing the sealant further to the sides to hopefully grasp onto the gasket more but to no avail. What could I be doing wrong? Thank you for any more advice!
You might have commented on the wrong video. None of those were things I showed in this one.
What about a tire patch? Covers hole with fresh rubber, adhered with appropriate glue.
Nice! Do you think the electrical tape will work if there is a chunk of the seal missing?
Not as well, but you might be able to reinforce the gap behind the tape with a flexible adhesive.
@The Snekker Show I'll give that a shot. Thanks for the quick response.
@@lumpvision5746 how did you get on with this. Debating on whether to try this or just get a new one
@Fern Home & LifeStyling Failed! I had a big chunk missing from my seal. This is probably best for a tear or crack. I'd give it a shot if your damage looks anything like it looks in the video. It'll cost a lot less than getting a new unit if you are successful.
@Fern Home & LifeStyling OH. So instead of getting a new unit, I got the seal replaced. Everything is good to go now.
Haha had the same problem a couple of years ago and it's still holding up.
I probably could have fixed it permanently with some exterior electrical tape.
@@TheSnekkerShowWith the exterior electrical tape would the tape still curl after every wash cycle and need to be restuck. Or is that the exact reason you're using the exterior tape to limit that step.
@zg-shred I suspect, but haven't tested, that an exterior grade electrical tape would last much longer because the water wouldn't affect it as much. But again, this is only intended to be a temporary solution so the machine can still be used while a long-term repair is being figured out.
Very clever fix!
Why not just remove the gasket/seal with the comprised spot and relocate to the top where water is not in contact with the seal until the new one arrives? Nice fix I will have to say!
These have to be installed a certain direction, and have connections for electrical and water. Changing it involves taking the machine halfway apart.
@@TheSnekkerShow ok it was keyed and I did not give that any though, 😁🛫
Tramel glue works great
I have a slightly different problem. I installed a new gasket. Ran washer and it leaks from the front where the seal meets the door. it looks like because it was folded while in the box, the fold was right at the point where the bottom arrow is, so it indents there and lets water by. i don't know if it will eventually shape out to fit or if i should return now.
@MichaelPSmith-mps Mine was a little creased when I got it, too. If it were mine, I'd give it a day or two to see if it corrects itself.
Plot twist: The door is superglued shut.
OH Man you r fok1ng Genius , thanks for share , for sure you help a lot of people with this video , Im going to fix mi washer machine this weekend , greetings from San Jose Ca
Thank you❤
Thanking you in advance, fingers crossed this works for our w/m! 🙏🙏💕
Good luck!
The door seal could also be leaking from the inside leading one to believe it's not the seal but perhaps a hose or maybe the pump.
That's what happened to mine. After removing the lower cover I started a load, and found the leak in the seal on the inside. Hope this helps someone.
Thank you for this!
😂 thank you for the wonderful tip!
Brilliant
Thank you
You're quite welcome.
Thank u
Umm... can't you just remove the seal reinstall it with the hole on the top, where the won't be much water to leak?
@@medawc519 It only fits one way.
I have LG wm2277hw in my house, we found it when we moved in. It has been almost 9 years we have been using the machine.
Lately we found pieces of plastic clogging up in the drain filters and it turned out to be the plastic drum that enclosed the stainless drum started to crack and chips off.
My guess is, this machine about 19 years old, I guess yours might have the same fate. It is time for a new machine.
If you bought a new gasket, why not just change out the gasket?
I can answer a little better now after confirming that the job would go pretty much as I expected. The whole thing took about six hours, frequently interrupted by dad responsibilities, and I also decided to clean, treat, and paint some rusted parts around the detergent tray, and also needed to unclog a drain line. Having done it once now, it would probably take 30-45 minutes the next time, assuming no additional maintenance.
@@TheSnekkerShow I asked "why you didn't change out the gasket"...Not how long it took or what else you did.
@@truth-ox3wz Well, you got bonus amplifying information. No need to whine about it.
@@TheSnekkerShow Whine about it...WHAT??? All, I asked is why you didn't change out the gasket, and all you want to be is a tuff guy. Would love to see you call me a whinner to my face.
Maybe he’s showing a temporary fix for people who don’t have a replacement seal yet but still want to do their laundry.