The pilot screw washer did exactly what you said. It came shooting out when I removed a separate part. That is the reason I looked up your video. I had to figure out where it was supposed to go lol. Thank you!
See I wondering about that. I had two jets left over but didn’t see anything on the outside. Thank god I didn’t install them yet. Appreciate it man. Good video.
Great video, really appreciate it. I do have a question though. Up near the float there is that chrome hollow pin, where does it go? When I opened my float bowl it fell out like it was just loose in there.
Do you have a video removing this rear carb from the bike? I just inherited a 1998 vz 800, been sitting for years and my carb is also spitting gas out of the breather hose. I'm just not sure how to get it off the bike safely.
Hello , could you please help me? I just changed my handlebar and needed to order longer cables, what i did for my Marauder. Somehow even i bought a + 150 mm cable, this one seems to be very short to reach the carburator. Is there kind of relay under the tank ??? How does it work? Where to find very long cables that fit my bike? Thank you so much for help !
The single throttle cable runs down to a splitter that seems to be part of the throttle cable assembly. I quickly attempted to take it apart for a cleaning but quickly gave up as it wasn't causing problems so I left it alone. If I had to guess, it's likely an entire throttle assembly.
Trevor, this video was very helpful as I am learning about my bike as I go. Could you possibly post a link to the kits that you bought? I have looked on amazon and am not finding any with all of the right parts.
The pilot screw washer did exactly what you said. It came shooting out when I removed a separate part. That is the reason I looked up your video. I had to figure out where it was supposed to go lol. Thank you!
See I wondering about that. I had two jets left over but didn’t see anything on the outside. Thank god I didn’t install them yet. Appreciate it man. Good video.
Also for the pilot screw, is there any turn type of spec? Everything I’ve read says pre-set. Which to me sounds like snug it up but just curious.
Where's the link for the kit
So what Kit do I need to get for both the carbs?
Hi!
Can You tell me please.,how did you take out the pin of the float?
Thanks
Hi Trevor what size drill bit did you use before using the extractor on the idle jet
Thanks
Peter
Brilliant vid, thanks again for sharing. Cheers.!!
Hey Trevor, can you share the link to order this kit? Or what part number did you use to find the right kit? thanks.
I was actually going to ask the same thing. Did you happen to locate a good kit?
The pilot screw has the screw spring and o ring then washer
Trevor.. could you tell me where the little o rings, in the plastic bag go ????
O ring goes in pilot screw one does
Great video, really appreciate it. I do have a question though. Up near the float there is that chrome hollow pin, where does it go? When I opened my float bowl it fell out like it was just loose in there.
Man I sold that bike years ago but if I remember correctly, that chrome pin is what the float rotates on.
Was it a pain to sync the carbs together. With it being a push pull carb.
Do you have a video removing this rear carb from the bike? I just inherited a 1998 vz 800, been sitting for years and my carb is also spitting gas out of the breather hose. I'm just not sure how to get it off the bike safely.
Hello , could you please help me? I just changed my handlebar and needed to order longer cables, what i did for my Marauder. Somehow even i bought a + 150 mm cable, this one seems to be very short to reach the carburator. Is there kind of relay under the tank ??? How does it work? Where to find very long cables that fit my bike?
Thank you so much for help !
The single throttle cable runs down to a splitter that seems to be part of the throttle cable assembly. I quickly attempted to take it apart for a cleaning but quickly gave up as it wasn't causing problems so I left it alone. If I had to guess, it's likely an entire throttle assembly.
Trevor TheEngineer thanks for your answer, i'm gonna take the bike to a station.
Glad I was able to help! Hope it all works out for you.
Need the part number
Great Video Trevor. I am in the process of tearing mine down for the same issue as well. Where did you source the rebuild Kits?
Hey sorry for the late response but I got mine on amazon!
Trevor, this video was very helpful as I am learning about my bike as I go. Could you possibly post a link to the kits that you bought? I have looked on amazon and am not finding any with all of the right parts.
What's the link
What’s the link
Where's the link for the kit
Looks equivalent to the one I got off of parts giant. It doesn’t include new floats or diaphragms but everything else fits OE on them.