ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก

Replacing Commonly Worn & Knocking Solid Rear Axle Bushes On A 2010 Ford Fiesta

แชร์
ฝัง
  • เผยแพร่เมื่อ 15 มี.ค. 2024
  • Every Ford Fiesta will require these bushes to be replaced at least once during it’s lifetime. They can wear to a point where they will also fail an MOT due to excessive movement.
    In this video, i’ll show you typical symptoms of worn bushes, how to diagnose them and the process of how to replace them.
    You will undoubtedly require specialist tooling to successfully complete replacement and safety is paramount. Although I’ll show you the process it can present a dangerous situation when lifting the vehicle and axle independently. Please take your time, be careful and ensure you use safety equipment at all times.
    Thank you in advance for all your support and please don’t hesitate to like, comment and support the channel by subscribing.

ความคิดเห็น • 25

  • @peterrudy9207
    @peterrudy9207 4 หลายเดือนก่อน +5

    When I change my cars oil at every 5000 miles . Thankfully by use of a mechanics lift . I liberally spray 303 Protectant on all rubber parts . As this will help them resist drying out and cracking .

  • @lloydwiltshire8302
    @lloydwiltshire8302 5 หลายเดือนก่อน +9

    Removing the old bush is really easy. Obviously it doesn’t matter how destroyed they get as the are heading for the bin anyway. So get yourself a good electrician holesaw and arbour. It needs to be larger than the aluminium internal bolt holder but smaller than the hard plastic shell of the bush. Simply run the cutter through, then carefully with a recip saw if you have one or a reversed hack saw. Blade through the big hole then reattach to the saw. Carefully cut the hard plastic without damaging the metal. One good hit with a mechanic chisel or an old screwdriver and she’s out. To clean the inside, a cheap old flappy sand paper disk in a drill does a great job.

  • @andrewwmacfadyen6958
    @andrewwmacfadyen6958 4 หลายเดือนก่อน +6

    Worn rear bushes are a Ford tradition since the MK3 Cortina

  • @kevinpalmer7452
    @kevinpalmer7452 2 หลายเดือนก่อน +1

    I’ve struggled to get those bushes out before working in a busy garage done a lot of these all I do is gently hear the eye of the axle that contains the bush and a couple of swift blows with a hammer and they fly out works every time 👍

  • @mopedbanzi3275
    @mopedbanzi3275 หลายเดือนก่อน

    Great instructional video, personally i think the air hammer is abit of a rough way of doing this job but you did a great cleanup i go for the drilling and sabre blade reciprocating saw method myself

  • @davida871
    @davida871 5 หลายเดือนก่อน +2

    Very detailed video. Thank you.

  • @arthurmatthews9321
    @arthurmatthews9321 2 หลายเดือนก่อน

    These are easy to do . Just use a hole cutter on a drill to take the central part of the bush out. Then get a air saw and cut the metal bush carrier . Once it’s cut through it will break the tension and can be tapped out easy. Then use a bearing puller to pull the new bush in.

  • @fishygaming9192
    @fishygaming9192 3 หลายเดือนก่อน +1

    I find the easiest method to remove is to drill 1 or 2 holes with 6 mm drill bit between edge of bush splitting the plastic surround then couple hits with hammer and comes out. Great vid though.

  • @Wolfpack310
    @Wolfpack310 11 วันที่ผ่านมา

    Really this the easiest thing, I did this today

  • @Shavenuw129
    @Shavenuw129 2 หลายเดือนก่อน +1

    Mine were an advisory on the last MOT. The garage changed them as it was a bit beyond my limited DIY mechanic skills

    • @jayrx12
      @jayrx12 23 วันที่ผ่านมา +1

      That was the right move, took me 10 hours to do on my own lol.

  • @nosas66
    @nosas66 4 หลายเดือนก่อน +1

    Great stuff

  • @danielmansilla8361
    @danielmansilla8361 หลายเดือนก่อน

    Excelente video. Gracias a la traducción pude entender. Saludos

  • @websurfer1585
    @websurfer1585 4 หลายเดือนก่อน +2

    I can't understand why a simple round bush has to be positioned in a certain spot like this?

    • @mopedbanzi3275
      @mopedbanzi3275 หลายเดือนก่อน

      i've wondered that too if it's today with the cutouts in the rubber and how it flexs possibly ?

  • @petersomthing9508
    @petersomthing9508 5 หลายเดือนก่อน +1

    Good video make more 😀

  • @johnmordue7262
    @johnmordue7262 10 ชั่วโมงที่ผ่านมา

    They knock out with a long tubular socket (it's actually the input sleeve socket for transit gearboxes) and I'm only 5:6 and 11 stone... clowns with drills,saws and air hammers.... and I missed the part where the torque wrench came into play and the axle/bush bolt were renewed 😂😂

  • @dc6869
    @dc6869 3 หลายเดือนก่อน

    Just replace with poly bushes.easy peazy

    • @Kenny.1979
      @Kenny.1979 3 หลายเดือนก่อน

      How do you reposition the bracket to the exact position it was in before removing?

    • @tony78uk48
      @tony78uk48 3 หลายเดือนก่อน +1

      I did that on my golf when they went .🙂👍

    • @jayrx12
      @jayrx12 23 วันที่ผ่านมา

      polyurethane my beloved

    • @benjaminlocksmith8932
      @benjaminlocksmith8932 12 วันที่ผ่านมา

      Paint around the mounting surface so you can line it up exactly as it came out ​@@Kenny.1979

    • @johnmordue7262
      @johnmordue7262 10 ชั่วโมงที่ผ่านมา

      Try following the workshop manual thats if you can read😂😂​@Kenny.1979

  • @garyfutcher6741
    @garyfutcher6741 3 หลายเดือนก่อน +1

    Shouldn't have used air chisel as youve damage the axle cut with hacksaw. Wouldn't use your garage lols