Thank you very much, this was very helpful. My integra gsr distributor wiring harness and the sensor on harness was shot. Replace wire and sensor, got a code 8. Which is a tdc sensor. Reason why cuz the magnet wasn't even close. Readjust magnet . Now everything is working great. No more code.
awesome vid bro thanks i was having a dizzy issue and i wanted to rebuilt another distributor and now i this vid just helped me save what lil money i have lol thanks guys 👍🔰🏎💨
Cool vid,I had trouble removing my old damaged icm from integra gsr obd2 distributor it seems stuck and I'm going to remove the dizzy tomorrow to make it easier.
damn it boii! I got a bit of a leak right where the distributor is. Is it possible to get away with it without disassembling the whole distributor? Could it be just the little O-ring that goes into the head?
Yes mate. This video shows the replacement of the internal seal, which will fix an oil leak into the inside of the dizzy. If the leak is external (originating from where the dizzy mates with the head), then replacing the o-ring on the end of the housing will sort this leak out. Mark your distributor position relative to the head, unplug everything, remove the 3 mounting bolts, and replace the o-ring.
Does anyone offer an oem rebuild service for those of us who have Hondata CPR conversion and no longer need the coil and igniter? I only need a rebuild for the remaining part of it. I currently had to replace it with a Duralast last one but my Billet cap doesn't fit with the aftermarket distributor. I know I know cosmetic only but it started getting to me over time.
I am putting a Obd2 H23a1 in a obd1 car and it won’t start... if I put the obd1 distributor internals in my Obd2 distributor... will that allow the engine to fire up...
+Dan Phillips No, Unless you replace all (( ALL )) Computer parts,,, which most do not work unless you go aftermarket,..,.,., While going after market there is no reason to do this.,.,.,.,, it will cost you more to do this,.,., than to get an engine swap to B-18 where more Options are Available.
It took me over a year to find that cluster. I think it was in a 97 B16 del sol. There's one in that red lines at 7200, one that red lines at 8000 and this one that red lines at 8200.
Thank you very much, this was very helpful. My integra gsr distributor wiring harness and the sensor on harness was shot. Replace wire and sensor, got a code 8. Which is a tdc sensor. Reason why cuz the magnet wasn't even close. Readjust magnet . Now everything is working great. No more code.
Thanks for the super informative content. Just got done rebuilding my dizzy.
Don't forget to set your ignition timing(if needed) when you put the distributor back on!
Very informative video, your editing style is very nice, keep it up!!!!!!
I wish you guys would upload more videos because the videos you do are great! Keep it up!
awesome vid bro thanks i was having a dizzy issue and i wanted to rebuilt another distributor and now i this vid just helped me save what lil money i have lol thanks guys 👍🔰🏎💨
facts ! This is my situation rn haha
Thank you, this helped me rebuild my leaky, impossible to find HX distributor.
Finally a decent video and full of details.
Cool vid,I had trouble removing my old damaged icm from integra gsr obd2 distributor it seems stuck and I'm going to remove the dizzy tomorrow to make it easier.
Where are these rebuild kits sold
Subbed yesterday, and you guys already uploaded a new video. Glad i subscribed, keep up the good work guys! :D
Welp, this video saved me from having to buy a brand new h23a jdm distributor, thanks 🙏
Do you guys use any dielectric grease on the contacts for the icm at all or no?
Very helpfull video,no tock is ok understand clearly.Tanks.
Where can I buy all of those parts
What if your rotor doesn't have a screw and the rotor is just pressed on? Will I be able to rebuild it?
Will really appreciate it.
Do they still sell shaft seals for oem dizzys?
how do you fix if you forget to mark it before removing the pin
Where did you buy the rebuild kit?
what kind of cleaners/ lubricants did you use?
Where can you order the seals/o rings to rebuild
more vids would be greatly appreciated good work
another great tech video, thanks!!!
where did u get those shaft seals??? PLZ let me know
Great videos. Needs some r18 videos in here.
So the "magnets" are the position sensors? Can I replace these with new units?
damn it boii! I got a bit of a leak right where the distributor is. Is it possible to get away with it without disassembling the whole distributor? Could it be just the little O-ring that goes into the head?
Yes mate. This video shows the replacement of the internal seal, which will fix an oil leak into the inside of the dizzy. If the leak is external (originating from where the dizzy mates with the head), then replacing the o-ring on the end of the housing will sort this leak out. Mark your distributor position relative to the head, unplug everything, remove the 3 mounting bolts, and replace the o-ring.
thanks for this, video really helped alot
Thanks. This video is very helpful
Can you.give me the colours of wire to join to the harness the plug burnt out. Thank you
Thanks guys great video
Had the distributor off by 180 degrees but how do you know it's off by that much before installation?
what were the symptoms? was it a crank no start afterwards? cause i think i just have that issue...
Does anyone offer an oem rebuild service for those of us who have Hondata CPR conversion and no longer need the coil and igniter? I only need a rebuild for the remaining part of it. I currently had to replace it with a Duralast last one but my Billet cap doesn't fit with the aftermarket distributor. I know I know cosmetic only but it started getting to me over time.
Hey man. Can you list what sensors are where?
I have a 1992 Honda Civic sedan and a 1995 Acura GSR engine on it the engine cranks and everything but have no spark what you think it is
Do you know where I can get the distributor key for my dizzy it’s for a 91 civic 1.5 d15b1 ?
Very good.......Brazil
whats the name of the song thats playing in the video? i like it..
can you install any ls vtec distributor in your car or you need to know the year of the head ?
I am putting a Obd2 H23a1 in a obd1 car and it won’t start... if I put the obd1 distributor internals in my Obd2 distributor... will that allow the engine to fire up...
god i fucking love cars & i hope we may never stop wrenching ! stop producing harder to work on cars ! *cough* chevy
+XSTAYUPX All Manufacturer Engineers are Paid to do this. Otherwise Auto shops Would not be in business,.., Although I do agree with this statement.
+bob dole Chevrolet is not ALONE on this
Do not misunderstand!
After replacing the coil, rotor/cap, S.Plugs, and spark plug wires, car through a code9 (obd1).
Artie the code 9 is a cyp sensor I have the same issue I was wondering exactly what part is the cyp sensor is it that magnet he refers to
Repair1995hondaodysseydesebertorcapeliveandslow
0:49 industrial themed adult entertainment music, lol
Nice❤
you forgot to replace the bearing
Hello, I am preparing a similar video for French-speaking CRX enthusiasts. 😀
why cant i remove the pin after i take off the key snap ring
more videos please!
Could I turn a Non VTEC H 23 A auto into a manual VTEC motor by changing the head and replacing the transmission and pedal assembly.
+Dan Phillips No, Unless you replace all (( ALL )) Computer parts,,, which most do not work unless you go aftermarket,..,.,., While going after market there is no reason to do this.,.,.,.,, it will cost you more to do this,.,., than to get an engine swap to B-18 where more Options are Available.
AND SET THE TIMING IN SERVICE MODE....AFFF
hey man , I was hoping to know where is the camshaft sensor located ! can u please tell where it is located inside the distributor?
lifenz1 yea it’s in tha distributor.
Nice production Mark. We need to catch up, I am working on a new project myself, 91 stealth tt awd. Hit me up buddy.
Do I really need the magnets? Why have magnets anyway.
Those aren't magnets - they are pickup coils for crank position, camshaft position and TDC position.
Help which one is for ckp p and which one is for cyk p?
Rising sun tat??
Is this for a z6 I need to know asap please
All d forusre and b series I'd imagine too
what cluster is that tho ??
It took me over a year to find that cluster. I think it was in a 97 B16 del sol. There's one in that red lines at 7200, one that red lines at 8000 and this one that red lines at 8200.
😊
shoulda showed how to replace bearing
what was the total cost?
Richard Sosa more than a new assembly
@@spankthemonkey3437 If this was a td42-u distributor, then good luck finding one new lol. Only OEM new one's I can find are $500+
You can buy a brand new dizzy for as much as coil will cost you.
uhh ... what about retiming it?
music start
Last step, GET THE TIMING DONE
how does one do that?
I want u teech me for upgrade vtech engine N/A
Pappu dass
I have a 1992 Honda Civic sedan and a 1995 Acura GSR engine on it the engine cranks and everything but have no spark what you think it is
More videos please!