Jhemcu GHF411AIO Pro F4 aio FC/ESC 35amp. Brief overview/My thinkings.....
ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2024
- Updated aio FC/ESC from Jhemcu, now with added 35amp ESC and DJI air unit connectivity.
Could this be the aio FC/ESC your looking for.............
Purchase it here:
35amp
www.banggood.c...
25amp
www.banggood.c...
Thanks for watching
Rich-TeaFPV
The above links are affiliate links, no effect on you but it helps the channel.
suggestion: stick the fc on a piece of paper and write the pins instead of saying stuff in the air. It would be much more useful as a screenshot at the end would show all wiring needs.
Thanks for the tip. I might try that in the future, thanks for watching
Are you kidding me? How you can make this video for 10 minutes and not show the underside of the board is beyond me! Do they have one or two MOSfets per motor?
Sorry mate, I'll make sure I flip the boards I'm looking at in the future, thanks for the feedback it's always helpful. Looks like there's 6 fets per esc so 24 in total, hope this helps. Thanks for watching 😁👍👍
@@Rich-TeaFPV I was waiting for mine and it was killing me. In the meantime it arrived and I wired it all up. Thanks for the video and reply
No problem 😀 happy ripping
Sir, meaning that this board can fly a fpv without ESC right?
It's an all in one board. With flight controller and esc built in 👍
Damn, this board doesn't have the name of the port on the board. Is it indicated in the manual?
Hello sir! I need a suggestion. Can I use BN-180 gps with this FC in Tx2 and Rx2? I am using Tx1 and Rx1 for digital fpv system and using sbus receiver.
Sorry I don't think you would have enough uarts
Thank you, very well done sir.
Can i use iflight 1104 4200kv motor with 4s battery xt30 connector at this fc?
It should be able to handle those motors, I have the older 30amp version of this board on my cinewhoop which has 1407 4100kv motors on 4s and I've had no issues so far. Thanks for watching 😁 👍 👍
I have jhemcu ghf411 pro 35amp. Try to use buzzer( 2wire + -) iput in pin buzzer and gnd. But can not loud. Can u help me please
hello, i bought this controller at bangood, i installed the matek 411 firmware, which entered without problems and i flashed the esc with bheli sh30, and everything was fine until i put the battery in, the accelerometer becomes unstable and doesn't work correctly it becomes totally to one side the drone, I don't know what's wrong.
what problem can it be?
Has anyone managed to install LED to this FC?
Should I go for 2308 motor ? , Company say it's ful throttle 55A in 4s , and I never gO to more then max 40 amps because li-ion can't deliver 😁
Personally I wouldn't use motors bigger than 2004 with this fc/esc. It might work but your pushing it to the maximum. The t-motor velox and pacer esc's are a great alternative with a higher amp rating for a good price. Thanks for watching 😁
@@Rich-TeaFPV but in my case my frame doesn't support 3 layer , like fc + ESC + vtx to think about fc+ESC combo , what you think ?
Maybe consider a nano vtx 🤔👍
@@Rich-TeaFPV but I have 2 30-30 and 1 20-20 vtx so I can't buy newone , any other suggestions.
Thank you for your reply ☺️
Hi Richard.
What Fw pre installed?
I want to use this fc with EMUflight.
It's got betaflight installed (forget which version, but definitely 4. something) so flashing EMUflight should be OK 👍. Thanks for watching. Oh and check the product page for the right. hex files you need as it changed from the previous version of this board
@@Rich-TeaFPV Thank you your reply.
I'm sorry. Would you give me the target name for pro version?
@@mitsuhashihiromi1581 just click the link in the description and look at product details all the information is there, don't worry it's not an affiliate link. 👍
I just installed this board in a four inch 3S with 2203 3450KV motors and 4023 props. I was able to update to the newest Betaflight and flashed the esc's with the 16.73 Jazz Maverick hex file. She tested good in the backyard so we're going out to the park today. Cheers.
Cool, I've got a similar project idea that I'll be looking at in a future video. It'd be great if you could tell us how it held up (or not) thanks 👍 👍
After update to jazz its not crash resistant in my end. Before it was crash resistant esc. Maybe im having bad luck burning motor 3 esc? With 25a 470uf cap tho
Could you plz help me?) I just updated the latest betaflight_4.2.4_STM32F411.hex firmware and gyro stop working. Then I flashed matekf411 target and gyro start work but motors are not spinning. Even ESC not enabled in the configurator ((( then I flashed STM one more time - the same issue >> gyro and all other things - ok, motors - NOT((
@@hanquah
Use JESC firmware and it's crash resistant with air mode, and bi directional d-shot works flawlessly.
Is it reliable? for 3inch tp build
Should be ok for a 3 inch build. I've not had any issues with this board which is all I can say. Thanks for watching 😁
I use this on 3" 3s toothpicks with 1303 5000kv and it's flawless after 100 flights 👍 even flashed with Jesc ESC firmware 48khz bi directional d-shot telemetry.
Great! half the clip out of focus....
where can i buy esc. mine is broken
Just had 3 out of 3 die after light crashes running 3S and driving 1408 motors. Real light duty stuff.
Dumping this AIO garbage and going back to single ESCs.
If your ESC stopped working (all 4 motors at once) it means that there is no power for ESCs uCU. You can replace a diode close to rx1 tx1 - it should solve your problem
Does the 9V output work on 3s, or even 2s batteries?
on 3s yes but 2s no. Thanks for watching😀
Ok... This means in those cases when the 3s voltage drops very low (during punch outs, or towards the end of the battery), there is a risk that the 9V switching power supply will brown out, and the Vista will freeze?
@@LotharKrupka in that circumstance yes you might get issues so I would stick to 4s if you think it might happen
so can you use a 6s on this board?
can I use it for 6s
For smaller motors on 6s maybe, without testing I couldn't say for certain so it's up to you. You could look at the amp draw chart on the product page for the motor your thinking of buying. Anyway sorry I couldn't be more helpful and thanks for watching.
im using 1600kv would that be okay
What size?
@@Rich-TeaFPV 1600kv motors on my 2fiddy build
@@SeeFPv-qm6ie so I'm thinking 2004 size. A aio board is recommended for that build so it might be OK. On paper it should be fine but jhemcu are a budget brand so take what they say with a pinch of salt. Personally I'd stick a throttle limit on betaflight to stop high amp draw just incase. But otherwise happy flying. 👍👍
Did you use sbus
I wanna use sbus for dji but no luck
Originally I used a flysky reciever (ibus) on an rx pad. But I've since moved the board onto another build with an sbus reciever. Not setup yet so I'll see how it goes. Thanks for watching 👍
Are the mounting holes m2 or m3? Thanks.
M2 👍
Where the smartaudio pad?
Any free tx pad on an unused uart will do 😁👍👍
Thankyou richard. Greeting from Indonesia
@@Rich-TeaFPV any? There are only 2 Tx pad (2 UARTs). One UART is for serial_rx. If you use the other one for GPS, then... no smartaudio.
@@Tonynux yep but if you use immersionrc ghost and your vtx uses irc tramp for smartaudio, connect the smartaudio to the ghost receiver and you can change bands, channel and power with the module
Considering the 25 amp version for 3 " toothpicks on 1105s and 1204s on 3s. Is it a decent board so far ? Looks like you have 2 choices of where to solder with the motor pads down the side or the 3 on the top.
That is exactly what he says..........
I use the Jhemcu 25 amp for my 3s 3" toothpick with 1303 5000kv motors and can confirm it is rock solid after 100 flights.