Husqvarna 350 Chainsaw Not Oiling-Fixed!
ฝัง
- เผยแพร่เมื่อ 16 ก.ย. 2024
- Customer complaint is that the bar isn't getting any oil. I'll show you what to look for and how to repair a Husqvarna 350 chainsaw and we will also look at the clutch and potential problems #smallenginerepair
Nice. I'm sure the customer appreciates you being able to get it done for him in a timely manner.
Merry Christmas
Customers do appreciate that and it helps give the shop a good reputation. Merry Christmas!
Your videos are extremely helpful. I don't see why you don't have s ton more subs!
Thanks for watching!
@@TheGreasyShopRag Later!
Great video, thanks Scott
Merry Christmas!
Mery Christmas!
Thats a sweet 350! Ive got one its a good little saw but it doesn't look like that! Good fix, well done!
Ya that one hasn't seen any abuse. Thanks for watching!
Great job, man 👍🏼
Thanks for watching!
Nice work as always the mighty 350 ,I’ve seen one with the brake spring melted into the case,I pried it off with a crow bar. They were great little saws until… catastrophic meltdown! Merry Christmas enjoy your Family
Merry Christmas!
Nice repair bud.. 🎅 Have a good Christmas 🎄
Merry Christmas!
Bless If I lived in your neck of the woods, I'd buy Husqvarna. But around here, repairs are not good. Thanks 😊
Thanks for watching!
Merry Christmas to you and everyone else thank you for the videos
Thanks and Merry Christmas to you!
Merry Christmas
Merry Christmas!
I picked up a 545 Mk II a few months ago.....I liked it so much that I found it's baby brother online.....a mint 345 fresh from a visit to a service center. Much the same as the one you are working on......very strong saws for the size....gotta take care of your equipment though.
Both of those are nice light powerful saws. Thanks for watching!
Love it
Thanks for watching
I took my ms 250 to stihl dealer because she didnt oil and replace oem carburetor.That was in 2021 and now she oils and runs perfect
Good deal. Don't let that gas get old, you don't want to have to replace the carb again. Thanks for watching!
Merry Christmas! Oh and good vid😂
Merry Christmas!
Did you get the story from the customer? I’m surprised that the heat didn’t transfer to the seal. Hope you and your family have a great Christmas.
No story. Merry Christmas!
@@TheGreasyShopRagjust curious. It appears the old adage is correct. Take care of your tool and it will take care of you.
Hi Scott, I'm trying to find information on the 1 piece vs. 2 piece oil hose design that comes on the 346XP. I thought I had seen in one of your videos where you pulled put the two piece and used the 1 piece because it sealed better. Any thoughts or video to watch? The 346 leaks worse than any of the 365, 350, 450, etc that I have.
It wasn't me that you saw do that so I don't really have anything to offer.
Nice Repair My Guess Is He Ran it With The Chain Brake on After It Kicked Back On Him Cause Hr Didn’t Understand How It Works Surprised He Didn’t Also Smoke The Clutch Drum Bearing Too 😮😮💨💨💨😀
They only do it once. After paying the bill they will get schooled.
@@TheGreasyShopRag That’s What I Say The Higher The Bill The More Education They Needed and Eventually They Will Learn 😎
@@chrischiampo7647 Lol
@@TheGreasyShopRag Merry Christmas By The Way 👍🏼
Quick question if you don't mind echo 125b blower doing a pressure test every port sealed when I go to pump up the tester the gage moves and falls right back down I used a spray bottle of water to check for the massiair leak there was none what could be the problem
Dunk it in a 5 Gallon Bucket Of Water Look For Bubbles as You Pressure It Up Might be Too Big of a Leak Too See With Soapy Water
Or Your Gauge is Leaking
I've never tried the 5 gallon bucket method. I usually regulate shop air down to 5 psi and hook it to the saw. I can usually hear the air leak and then I'll spray soapy water on it. Care must be taken using this method so you don't create leaks that weren't there before the testing started 🙂